Ben Freemire
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ben Freemire has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Chunguang Jing
Euclid Beamlabs LLC
4 shared publications - Yelong Wei
National Synchrotron Radiation Laboratory, University of Science and Technology of China, Hefei, China
3 shared publications - Carsten Peter Welsch
The University of Liverpool
2 shared publications E. Wisniewski
2 shared publications- Hikmet Bursali
CERN, Geneva CH-1211, Switzerland
2 shared publications J. Power
2 shared publications
Latest Publications
- Open Access
- 6 July 2023
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 26 (7) , 071301
Development of -band single-cell dielectric disk accelerating structuresShort-pulse two-beam acceleration (TBA) is a promising advanced accelerator concept that may meet the luminosity and cost requirements of future large-scale linear colliders. Accelerating structures with high group velocity (on the order of 0.1c) are required in this scheme to reduce the filling time so as to efficiently accelerate the main beam with multiple bunches. In conventional accelerating structures such as metallic disk-loaded and dielectric-loaded, high group velocity usually implies low shunt impedance, which limits the rf-to-main-beam efficiency and causes a bottleneck in the overall wall-plug-to-main-beam efficiency. A dielectric disk accelerator (DDA) is a hybrid structure, which has geometry similar to metallic disk-loaded accelerators, but replaces the metal disks with dielectric disks to form the cells. Such a configuration could achieve simultaneous high group velocity and high shunt impedance, making a DDA a very attractive candidate for the short-pulse TBA approach by significantly improving power efficiency. In this manuscript, we present the start-to-end development of two -band single-cell DDA prototypes, including the rf and mechanical design, fabrication, cold test, high power beam test, and post-test inspection. Of the two, a clamped structure performed better, achieving accelerating gradient from 320-MW input power.- 6 July 2023
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 26 (7) , 071301
Open AccessDevelopment of -band single-cell dielectric disk accelerating structuresShort-pulse two-beam acceleration (TBA) is a promising advanced accelerator concept that may meet the luminosity and cost requirements of future large-scale linear colliders. Accelerating structures with high group velocity (on the order of 0.1c) are required in this scheme to reduce the filling time so as to efficiently accelerate the main beam with multiple bunches. In conventional accelerating structures such as metallic disk-loaded and dielectric-loaded, high group velocity usually implies low shunt impedance, which limits the rf-to-main-beam efficiency and causes a bottleneck in the overall wall-plug-to-main-beam efficiency. A dielectric disk accelerator (DDA) is a hybrid structure, which has geometry similar to metallic disk-loaded accelerators, but replaces the metal disks with dielectric disks to form the cells. Such a configuration could achieve simultaneous high group velocity and high shunt impedance, making a DDA a very attractive candidate for the short-pulse TBA approach by significantly improving power efficiency. In this manuscript, we present the start-to-end development of two -band single-cell DDA prototypes, including the rf and mechanical design, fabrication, cold test, high power beam test, and post-test inspection. Of the two, a clamped structure performed better, achieving accelerating gradient from 320-MW input power. - Open Access
- 11 April 2022
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 25 (4) , 041301
Design, fabrication, and low-power rf measurement of an -band dielectric-loaded accelerating structureThis paper presents the design, fabrication, and low-power rf measurement of an externally powered -band dielectric-loaded accelerating (DLA) structure with a dielectric constant and a loss tangent . A dielectric matching section for coupling the rf power from a circular waveguide to an -band DLA structure consists of a compact dielectric disk with a width of 2.035 mm and a tilt angle of 60°, resulting in a broadband coupling at a low rf field which has the potential to survive in the high-power environment. Based on simulation studies, a prototype of the DLA structure was fabricated. Results from low-power rf measurements and the comparison with simulated values are presented. A significant discrepancy was found between measurements and simulations. The detailed analysis on the fabrication errors which may cause the discrepancy is also discussed.- 11 April 2022
- Published by American Physical Society (APS) in Physical Review Accelerators and Beams
- Vol. 25 (4) , 041301
Open AccessDesign, fabrication, and low-power rf measurement of an -band dielectric-loaded accelerating structureThis paper presents the design, fabrication, and low-power rf measurement of an externally powered -band dielectric-loaded accelerating (DLA) structure with a dielectric constant and a loss tangent . A dielectric matching section for coupling the rf power from a circular waveguide to an -band DLA structure consists of a compact dielectric disk with a width of 2.035 mm and a tilt angle of 60°, resulting in a broadband coupling at a low rf field which has the potential to survive in the high-power environment. Based on simulation studies, a prototype of the DLA structure was fabricated. Results from low-power rf measurements and the comparison with simulated values are presented. A significant discrepancy was found between measurements and simulations. The detailed analysis on the fabrication errors which may cause the discrepancy is also discussed. - Open Access
- 11 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 69 (5) , 991-1001
A Compact, Low-Field, Broadband Matching Section for Externally Powered X-Band Dielectric-Loaded Accelerating Structures
It has been technically challenging to efficiently couple external radiofrequency (RF) power to cylindrical dielectric-loaded accelerating (DLA) structures, especially when the DLA structure has a high dielectric constant. This paper presents a novel design of matching section for coupling the RF power from a circular waveguide to an X-band DLA structure with a dielectric constant εr = 16.66 and a loss tangent tanδ = 3.43 × 10-5. It consists of a compact dielectric disk with a width of 2.035mm and a base angle of 60°, resulting in a broadband coupling at a low RF field which has the potential to survive in the high-power environment. To prevent a sharp dielectric corner break, a 45° chamfer is also added. A microscale vacuum gap, caused by metallic clamping between the thin coating and the outer thick copper jacket, is also studied in detail. Through optimization, most of RF power is coupled into the DLA structure, with no enhancement of peak electromagnetic fields above those of the structure itself. Tolerance studies on the geometrical parameters and mechanical design of the full-assembly structure are also carried out as a reference for fabrication.
- 11 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 69 (5) , 991-1001
Open AccessA Compact, Low-Field, Broadband Matching Section for Externally Powered X-Band Dielectric-Loaded Accelerating Structures
It has been technically challenging to efficiently couple external radiofrequency (RF) power to cylindrical dielectric-loaded accelerating (DLA) structures, especially when the DLA structure has a high dielectric constant. This paper presents a novel design of matching section for coupling the RF power from a circular waveguide to an X-band DLA structure with a dielectric constant εr = 16.66 and a loss tangent tanδ = 3.43 × 10-5. It consists of a compact dielectric disk with a width of 2.035mm and a base angle of 60°, resulting in a broadband coupling at a low RF field which has the potential to survive in the high-power environment. To prevent a sharp dielectric corner break, a 45° chamfer is also added. A microscale vacuum gap, caused by metallic clamping between the thin coating and the outer thick copper jacket, is also studied in detail. Through optimization, most of RF power is coupled into the DLA structure, with no enhancement of peak electromagnetic fields above those of the structure itself. Tolerance studies on the geometrical parameters and mechanical design of the full-assembly structure are also carried out as a reference for fabrication.
- Open Access
- p. 3917-3920
Plasma Chemistry in a High Pressure Gas Filled RF Test Cell for use in a Muon Cooling Channel
- p. 3917-3920
Open AccessPlasma Chemistry in a High Pressure Gas Filled RF Test Cell for use in a Muon Cooling Channel