Cuili Wang
Research Subjects
Cuili Wang has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Fenglai Yang
PetroChina Tarim Oilfield Company, Korla 841000, China
3 shared publications - Junjie Zhong
State Key Laboratory of Deep Oil and Gas, China University of Petroleum (East China), Qingdao 266580, China
2 shared publications - Kun Zhou
PetroChina Tarim Oilfield Company, Korla 841000, China
2 shared publications - Sa Xiao
PetroChina Tarim Oilfield Company, Korla 841000, China
2 shared publications - Xuehao Pei
Exploration and Development Research Institute, Tarim Oilfield Company, China National Petroleum Corporation, Korla 841000, China
2 shared publications B H Song
Research Institute of Exploration & Development, Tarim Oilfield Company, PetroChina, Korla 841000 China
1 shared publication
Latest Publications
- Open Access
- 21 October 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (20) , 1601
Gas–Water Two-Phase Flow Mechanisms in Deep Tight Gas Reservoirs: Insights from Nanofluidics
Understanding gas–water two-phase flow mechanisms in deep tight gas reservoirs is critical for improving production performance and mitigating water invasion. However, the effects of pore-throat-fracture multiscale structures on gas–water flow remain inadequately understood, particularly under high-temperature and high-pressure conditions (HT/HP). In this study, we developed visualizable multiscale throat-pore and throat-pore-fracture physical nanofluidic chip models (feature sizes 500 nm–100 μm) parameterized with Keshen block geological data in the Tarim Basin. We then established an HT/HP nanofluidic platform (rated to 240 °C, 120 MPa; operated at 100 °C, 100 MPa) and, using optical microscopy, directly visualized spontaneous water imbibition and gas–water displacement in the throat-pore and throat-pore-fracture nanofluidic chips and quantified fluid saturation, front velocity, and threshold pressure gradients. The results revealed that the spontaneous imbibition process follows a three-stage evolution controlled by capillarity, gas compression, and pore-scale heterogeneity. Nanoscale throats and microscale pores exhibit good connectivity, facilitating rapid imbibition without significant scale-induced resistance. In contrast, 100 μm fractures create preferential flow paths, leading to enhanced micro-scale water locking and faster gas–water equilibrium. The matrix gas displacement threshold gradient remains below 0.3 MPa/cm, with the cross-scale Jamin effect—rather than capillarity—dominating displacement resistance. At higher pressure gradients (~1 MPa/cm), water is efficiently expelled to low saturations via nanoscale throat networks. This work provides an experimental platform for visualizing gas–water flow in multiscale porous media under ultra-high temperature and pressure conditions and offers mechanistic insights to guide gas injection strategies and water management in deep tight gas reservoirs.
- 21 October 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (20) , 1601
Open AccessGas–Water Two-Phase Flow Mechanisms in Deep Tight Gas Reservoirs: Insights from Nanofluidics
Understanding gas–water two-phase flow mechanisms in deep tight gas reservoirs is critical for improving production performance and mitigating water invasion. However, the effects of pore-throat-fracture multiscale structures on gas–water flow remain inadequately understood, particularly under high-temperature and high-pressure conditions (HT/HP). In this study, we developed visualizable multiscale throat-pore and throat-pore-fracture physical nanofluidic chip models (feature sizes 500 nm–100 μm) parameterized with Keshen block geological data in the Tarim Basin. We then established an HT/HP nanofluidic platform (rated to 240 °C, 120 MPa; operated at 100 °C, 100 MPa) and, using optical microscopy, directly visualized spontaneous water imbibition and gas–water displacement in the throat-pore and throat-pore-fracture nanofluidic chips and quantified fluid saturation, front velocity, and threshold pressure gradients. The results revealed that the spontaneous imbibition process follows a three-stage evolution controlled by capillarity, gas compression, and pore-scale heterogeneity. Nanoscale throats and microscale pores exhibit good connectivity, facilitating rapid imbibition without significant scale-induced resistance. In contrast, 100 μm fractures create preferential flow paths, leading to enhanced micro-scale water locking and faster gas–water equilibrium. The matrix gas displacement threshold gradient remains below 0.3 MPa/cm, with the cross-scale Jamin effect—rather than capillarity—dominating displacement resistance. At higher pressure gradients (~1 MPa/cm), water is efficiently expelled to low saturations via nanoscale throat networks. This work provides an experimental platform for visualizing gas–water flow in multiscale porous media under ultra-high temperature and pressure conditions and offers mechanistic insights to guide gas injection strategies and water management in deep tight gas reservoirs.
- Open Access
Reservoir Characteristics and Controlling Factors of Baxigai Formation in Bozi–Dabei Area, Kuqa Depression
The Lower Cretaceous Baxigai Formation is characterized by fan-delta front deposits and serves as a crucial target for ultradeep tight gas exploration in western China. Consequently, investigating its reservoir characteristics and controlling factors is critical. To characterize these reservoirs, we integrated well logs, core observation and analyses, thin-section petrography, high-pressure mercury injection, and scanning electron microscopy. This approach enabled comprehensive analysis of tight reservoir attributes and their genetic controls. Results show that the Baxigai Formation developed a fan-delta system, with premium reservoirs primarily concentrated in subaqueous distributary channels of fan-delta fronts. Reservoir lithology consists of medium- to fine-grained arkose and lithic arkose, exhibiting well-developed intergranular and intragranular dissolution pores alongside low mineralogical maturity. With average porosity of 2.76% and permeability of 0.24 × 10−3 μm2, these reservoirs are classified as low-porosity and medium–low-permeability systems. Depositional, diagenetic, and structural factors are the main controls on reservoir quality. Subaqueous distributary channels and mouth bars within the fan-delta system provide favorable conditions for reservoir development. Intergranular dissolution pores formed by feldspar dissolution and organic acid reactions play a key role in enhancing reservoir quality and supporting hydrocarbon generation. Structural fractures play a pivotal role in elevating permeability and establishing effective fracture–pore configurations.
Open AccessReservoir Characteristics and Controlling Factors of Baxigai Formation in Bozi–Dabei Area, Kuqa Depression
The Lower Cretaceous Baxigai Formation is characterized by fan-delta front deposits and serves as a crucial target for ultradeep tight gas exploration in western China. Consequently, investigating its reservoir characteristics and controlling factors is critical. To characterize these reservoirs, we integrated well logs, core observation and analyses, thin-section petrography, high-pressure mercury injection, and scanning electron microscopy. This approach enabled comprehensive analysis of tight reservoir attributes and their genetic controls. Results show that the Baxigai Formation developed a fan-delta system, with premium reservoirs primarily concentrated in subaqueous distributary channels of fan-delta fronts. Reservoir lithology consists of medium- to fine-grained arkose and lithic arkose, exhibiting well-developed intergranular and intragranular dissolution pores alongside low mineralogical maturity. With average porosity of 2.76% and permeability of 0.24 × 10−3 μm2, these reservoirs are classified as low-porosity and medium–low-permeability systems. Depositional, diagenetic, and structural factors are the main controls on reservoir quality. Subaqueous distributary channels and mouth bars within the fan-delta system provide favorable conditions for reservoir development. Intergranular dissolution pores formed by feldspar dissolution and organic acid reactions play a key role in enhancing reservoir quality and supporting hydrocarbon generation. Structural fractures play a pivotal role in elevating permeability and establishing effective fracture–pore configurations.
- Open Access
Molecular Simulation Study of Gas–Water Adsorption Behavior and Mobility Evaluation in Ultra-Deep, High-Pressure Fractured Tight Sandstone Reservoirs
Under high-temperature and high-pressure conditions, understanding the competitive adsorption and mobilization mechanisms of gas and water in fractured tight sandstone gas reservoirs is crucial for optimizing the recovery factor. This study employs molecular dynamics simulation to investigate the adsorption behavior and mobilization characteristics of H2O and CH4 in 10 nm quartz nanopores under the conditions of the Keshen fractured tight sandstone gas reservoir. The results indicate that H2O exhibits strong adsorption on the quartz surface, forming two high-density adsorption layers with a thickness of approximately 0.6 nm, whereas CH4 forms three adsorption layers with a thickness of about 1.1 nm. Under gas–water coexistence conditions, the competitive adsorption effect of the water phase significantly influences the distribution of CH4. Due to the hydrophilicity of the quartz wall, H2O molecules preferentially adsorb onto the wall surface, forming a stable water film that significantly inhibits CH4 adsorption. When the water saturation reaches 35%, water molecules form liquid bridges within the pores, segmenting the gas phase into different regions. As water saturation further increases, more stable liquid bridge structures develop, and microscopic water lock effects emerge, further restricting gas flow. During depletion development, H2O remains difficult to mobilize due to strong wall adsorption, with a recovery factor of only 7%. In contrast, CH4 exhibits high mobility, with a recovery factor of up to 75%. However, as water saturation increases from 30% to 70%, the recovery factor of CH4 decreases significantly from 75% to 29%, indicating that the water phase not only occupies pore space, but also exerts a blocking effect that significantly inhibits CH4 percolation and production. This study provides important theoretical support for the development strategies of ultra-deep fractured tight sandstone gas reservoirs and offers key insights for improving the ultimate recovery factor under gas–water coexistence conditions.
Open AccessMolecular Simulation Study of Gas–Water Adsorption Behavior and Mobility Evaluation in Ultra-Deep, High-Pressure Fractured Tight Sandstone Reservoirs
Under high-temperature and high-pressure conditions, understanding the competitive adsorption and mobilization mechanisms of gas and water in fractured tight sandstone gas reservoirs is crucial for optimizing the recovery factor. This study employs molecular dynamics simulation to investigate the adsorption behavior and mobilization characteristics of H2O and CH4 in 10 nm quartz nanopores under the conditions of the Keshen fractured tight sandstone gas reservoir. The results indicate that H2O exhibits strong adsorption on the quartz surface, forming two high-density adsorption layers with a thickness of approximately 0.6 nm, whereas CH4 forms three adsorption layers with a thickness of about 1.1 nm. Under gas–water coexistence conditions, the competitive adsorption effect of the water phase significantly influences the distribution of CH4. Due to the hydrophilicity of the quartz wall, H2O molecules preferentially adsorb onto the wall surface, forming a stable water film that significantly inhibits CH4 adsorption. When the water saturation reaches 35%, water molecules form liquid bridges within the pores, segmenting the gas phase into different regions. As water saturation further increases, more stable liquid bridge structures develop, and microscopic water lock effects emerge, further restricting gas flow. During depletion development, H2O remains difficult to mobilize due to strong wall adsorption, with a recovery factor of only 7%. In contrast, CH4 exhibits high mobility, with a recovery factor of up to 75%. However, as water saturation increases from 30% to 70%, the recovery factor of CH4 decreases significantly from 75% to 29%, indicating that the water phase not only occupies pore space, but also exerts a blocking effect that significantly inhibits CH4 percolation and production. This study provides important theoretical support for the development strategies of ultra-deep fractured tight sandstone gas reservoirs and offers key insights for improving the ultimate recovery factor under gas–water coexistence conditions.
- Open Access
- 11 July 2024
- Published by MDPI AG in Preprints.org
A New Test Method of “Nuclear Magnetic Resonance + High-Speed Centrifugation” for Gas-Water Relative Permeability Curve of Low-Permeability and Tight Sandstone
Gas-water relative permeability curve is the foundation of gas reservoir dynamic analysis and numerical simulation. It is generally obtained through gas displacing water experiment. Referring to the existing national standards, gas-water relative permeability test is carried out for low-permeability and tight sandstone. The flow is discontinuous and the curve smoothness is poor, which affects the application of gas-water relative permeability curve. Based on the comparative analysis of a large number of mercury injection and NMR experimental results of low-permeability and tight sandstone, a method to characterize the throat radius distribution of low-permeability tight sandstone based on NMR T2 spectrum is explored. Combined with high-speed centrifugal experiment, the calculation formulas of core water saturation, phase relative permeability of gas-water under different centrifugal force are established. A new method of "nuclear magnetic resonance + high-speed centrifugation" for gas-water relative permeability curve test of low-permeability and tight sandstone is formed, and the test is carried out on Sulige low-permeability tight sandstone core. The results show that: (1) The shape of cumulative distribution curve of throat radius by mercury injection method is basically consistent with that of T2 relaxation time by NMR, and there is a good corresponding relationship between them. (2) The centrifugation process is similar to the gas displacing water process. With the decrease of water saturation, water centrifugation in rock core becomes more and more difficult until it become irreducible. (3) The test process of the new method is unified and standard and up to 6 cores can be tested at the same time. The calculation results of water saturation and relative permeability curve are reliable and the integral curve is smooth, which greatly improves the test efficiency of gas-water relative permeability curve in low-permeability and tight sandstone. The new method can be widely used to study the gas-water two-phase seepage law in low-permeability and tight sandstone gas reservoir.
- 11 July 2024
- Published by MDPI AG in Preprints.org
Open AccessA New Test Method of “Nuclear Magnetic Resonance + High-Speed Centrifugation” for Gas-Water Relative Permeability Curve of Low-Permeability and Tight Sandstone
Gas-water relative permeability curve is the foundation of gas reservoir dynamic analysis and numerical simulation. It is generally obtained through gas displacing water experiment. Referring to the existing national standards, gas-water relative permeability test is carried out for low-permeability and tight sandstone. The flow is discontinuous and the curve smoothness is poor, which affects the application of gas-water relative permeability curve. Based on the comparative analysis of a large number of mercury injection and NMR experimental results of low-permeability and tight sandstone, a method to characterize the throat radius distribution of low-permeability tight sandstone based on NMR T2 spectrum is explored. Combined with high-speed centrifugal experiment, the calculation formulas of core water saturation, phase relative permeability of gas-water under different centrifugal force are established. A new method of "nuclear magnetic resonance + high-speed centrifugation" for gas-water relative permeability curve test of low-permeability and tight sandstone is formed, and the test is carried out on Sulige low-permeability tight sandstone core. The results show that: (1) The shape of cumulative distribution curve of throat radius by mercury injection method is basically consistent with that of T2 relaxation time by NMR, and there is a good corresponding relationship between them. (2) The centrifugation process is similar to the gas displacing water process. With the decrease of water saturation, water centrifugation in rock core becomes more and more difficult until it become irreducible. (3) The test process of the new method is unified and standard and up to 6 cores can be tested at the same time. The calculation results of water saturation and relative permeability curve are reliable and the integral curve is smooth, which greatly improves the test efficiency of gas-water relative permeability curve in low-permeability and tight sandstone. The new method can be widely used to study the gas-water two-phase seepage law in low-permeability and tight sandstone gas reservoir.
- Open Access
Characteristics and Effects of Laminae on a Cretaceous Reservoir in the Bozi–Dabei Area of the Tarim Basin, China
Reservoir heterogeneity is an important factor in oil and gas exploration and development. It has guiding significance for favourable target optimization because it helps clarify the formation and development characteristics of laminae: thin, alternating layers of sediment deposited in a repeating pattern in Cretaceous sandstone reservoirs. Reservoir heterogeneity is higher when laminae are densely distributed. For example, laminae have a significant influence on reservoir properties in the Kelasu structural belt in the Bozi–Dabei area, Tarim Basin, China, where oil and gas wells have very low productivity. Hence, this study attempts to develop a classification scheme based on laminae to identify how they influence reservoir properties. Based on an analysis of cores, thin section and logging imaging data, laminae in this area can be classified into three types: magnetite-enriched, iron-stained argillaceous-enriched, and grain-size change. Results show that magnetite-enriched and iron-stained argillaceous-enriched laminae are well-developed in the BZ1 and DB10 well areas in northern Bozi. They have much lower porosity compared to a non-laminae reservoir and their lateral permeability is greater than vertical permeability. Grain-size change laminae are well-developed in the southern Bozi region. For the laminated reservoirs, increasing the length of the perforation interval and the perforation density using sand or acid fracturing is an effective method for communicating with the vertical reservoir layers, improving permeability, and increasing single-well production.
Open AccessCharacteristics and Effects of Laminae on a Cretaceous Reservoir in the Bozi–Dabei Area of the Tarim Basin, China
Reservoir heterogeneity is an important factor in oil and gas exploration and development. It has guiding significance for favourable target optimization because it helps clarify the formation and development characteristics of laminae: thin, alternating layers of sediment deposited in a repeating pattern in Cretaceous sandstone reservoirs. Reservoir heterogeneity is higher when laminae are densely distributed. For example, laminae have a significant influence on reservoir properties in the Kelasu structural belt in the Bozi–Dabei area, Tarim Basin, China, where oil and gas wells have very low productivity. Hence, this study attempts to develop a classification scheme based on laminae to identify how they influence reservoir properties. Based on an analysis of cores, thin section and logging imaging data, laminae in this area can be classified into three types: magnetite-enriched, iron-stained argillaceous-enriched, and grain-size change. Results show that magnetite-enriched and iron-stained argillaceous-enriched laminae are well-developed in the BZ1 and DB10 well areas in northern Bozi. They have much lower porosity compared to a non-laminae reservoir and their lateral permeability is greater than vertical permeability. Grain-size change laminae are well-developed in the southern Bozi region. For the laminated reservoirs, increasing the length of the perforation interval and the perforation density using sand or acid fracturing is an effective method for communicating with the vertical reservoir layers, improving permeability, and increasing single-well production.
- Open Access
- 1 November 2020
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 600 (1) , 012029
Development characteristics and formation stages of tectonic fractures of Cretaceous Bashijiqike tight sandstone reservoir in Keshen gas field, Tarim Basin, China
The Cretaceous Bashijiqike formation in the Kuqa Depression of the Tarim Basin is ultra-low porosity and ultra-low permeability reservoir, where fractures have important influences on single well productivity and natural gas accumulation. According to the core CT scanning, casting thin section, laser copolymerization, imaging logging and other data, the basic development characteristics of fracture in this area are analyzed. Based on the analysis results of the core fracture cutting relationship, the carbon and oxygen isotope of the fractures filling, and the temperature measurement of the inclusions, the main stages of the regional fractures are determined. The results show that the fractures in the study area are mainly high angles, mostly filled with calcite and gypsum, and the fracture width is generally less than 0.2mm. There are three groups of structural fractures, which are EW/NE-SW and NW-SE, with the dominant orientations being NE-SW and NW-SE. The structural fracture were formed in three stages, which were the late Yanshan movement period-early Himalayan tectonic movement, the middle period of Himalayan, and the late period of Himalayan tectonic movement. The tectonic activity of the late Himalayan tectonic movement is the strongest, and the formation of fractures formed in this period were low degree of filling and effective.
- 1 November 2020
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 600 (1) , 012029
Open AccessDevelopment characteristics and formation stages of tectonic fractures of Cretaceous Bashijiqike tight sandstone reservoir in Keshen gas field, Tarim Basin, China
The Cretaceous Bashijiqike formation in the Kuqa Depression of the Tarim Basin is ultra-low porosity and ultra-low permeability reservoir, where fractures have important influences on single well productivity and natural gas accumulation. According to the core CT scanning, casting thin section, laser copolymerization, imaging logging and other data, the basic development characteristics of fracture in this area are analyzed. Based on the analysis results of the core fracture cutting relationship, the carbon and oxygen isotope of the fractures filling, and the temperature measurement of the inclusions, the main stages of the regional fractures are determined. The results show that the fractures in the study area are mainly high angles, mostly filled with calcite and gypsum, and the fracture width is generally less than 0.2mm. There are three groups of structural fractures, which are EW/NE-SW and NW-SE, with the dominant orientations being NE-SW and NW-SE. The structural fracture were formed in three stages, which were the late Yanshan movement period-early Himalayan tectonic movement, the middle period of Himalayan, and the late period of Himalayan tectonic movement. The tectonic activity of the late Himalayan tectonic movement is the strongest, and the formation of fractures formed in this period were low degree of filling and effective.