D. Anjaiah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
D. Anjaiah has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
N. Yagnesh Sharma
Department of Mechanical and Manufacturing Engineering, Manipal Institute of Technology, Manipal University, Manipal 576104, India
2 shared publicationsB.R.N Murthy
Department of Mechanical and Manufacturing, Manipal University, India
1 shared publication- Deepak Doreswamy
Department of Mechatronics, Manipal Institute of Technology, Manipal Academy of Higher Education, Manipal, India
1 shared publication K. Vasudeva Karanth
Department of Mechanical and Manufacturing Engineering, Manipal Institute of Technology, Manipal University, Manipal 576104, India
1 shared publicationL.L. Raj Rodrigues
Department of Mechanical and Manufacturing, Manipal University, India
1 shared publication
Latest Publications
- Open Access
- 1 January 2012
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 4
CFD Simulation of Flow in an Abrasive Water Suspension Jet: The Effect of Inlet Operating Pressure and Volume Fraction on Skin Friction and Exit Kinetic Energy
Abrasive particles in the suspension mixture in an abrasive water suspension jet (AWSJ) machining causes acute skin friction effect thereby effectively changing the jet diameter due to wear, which in turn influences jet exit kinetic energy. This results in lowering the life of the jet for effective machining. In consideration of this aspect, the present work examines the effect of inlet pressure on skin friction coefficient and jet exit kinetic energy. It is inferred from the analysis that an increase in inlet pressure causes a significant increase in skin friction coefficient and also results in proportional increase in the exit kinetic energy of the jet. Further, it is revealed from the analysis that an increase volume fraction of abrasive (abrasive concentration) in water results in significant decrease in the skin friction coefficient and jet exit kinetic energy.
- 1 January 2012
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 4
Open AccessCFD Simulation of Flow in an Abrasive Water Suspension Jet: The Effect of Inlet Operating Pressure and Volume Fraction on Skin Friction and Exit Kinetic Energy
Abrasive particles in the suspension mixture in an abrasive water suspension jet (AWSJ) machining causes acute skin friction effect thereby effectively changing the jet diameter due to wear, which in turn influences jet exit kinetic energy. This results in lowering the life of the jet for effective machining. In consideration of this aspect, the present work examines the effect of inlet pressure on skin friction coefficient and jet exit kinetic energy. It is inferred from the analysis that an increase in inlet pressure causes a significant increase in skin friction coefficient and also results in proportional increase in the exit kinetic energy of the jet. Further, it is revealed from the analysis that an increase volume fraction of abrasive (abrasive concentration) in water results in significant decrease in the skin friction coefficient and jet exit kinetic energy.
- 1 September 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 87-90
Influence of process parameters on the quality of hole in drilling of GFRP composites - an experimental investigation using DOE
In recent days composites are finding wide application in all fields because of their specific properties. Drilling is the most common machining operation performed on composites and the quality of hole has an important bearing on its applications. The quality of the drilled hole is mainly defined by delamination, surface roughness, and cylindricity, and it depends upon process variables such as thrust and torque. This paper deals with the study of the influence of process parameters on the quality of hole in drilling of Glass Fiber Reinforced Polymer (GFRP) composites. The results have shown that the drill geometry has major influence on the quality of drilled hole in comparison to drill size, work-piece thickness, volume fraction, fiber orientation, speed and feed.
- 1 September 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 87-90
Influence of process parameters on the quality of hole in drilling of GFRP composites - an experimental investigation using DOE
In recent days composites are finding wide application in all fields because of their specific properties. Drilling is the most common machining operation performed on composites and the quality of hole has an important bearing on its applications. The quality of the drilled hole is mainly defined by delamination, surface roughness, and cylindricity, and it depends upon process variables such as thrust and torque. This paper deals with the study of the influence of process parameters on the quality of hole in drilling of Glass Fiber Reinforced Polymer (GFRP) composites. The results have shown that the drill geometry has major influence on the quality of drilled hole in comparison to drill size, work-piece thickness, volume fraction, fiber orientation, speed and feed.