Beate Capraro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Beate Capraro has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Heike Bartsch
Technische Universitt Ilmenau (TU Ilmenau),Institute of Micro- and Nanotechnologies MacroNano, Electronics Technology Group,Ilmenau,Germany,98693
4 shared publications - Jörg Töpfer
Department of SciTec, Ernst-Abbe-Hochschule Jena, Jena, Germany
4 shared publications Jens Müller
IMN MacroNano Ilmenau University of Technology 98693 Ilmenau Germany
2 shared publicationsRomy Löhnert
2 shared publicationsStefan Barth
Fraunhofer Institute of Ceramic Technologies and Systems 07629 Hermsdorf Germany
2 shared publicationsAlexander Schulz
Electronics Technology Group, Technische Universität Ilmenau, Ilmenau, Germany
1 shared publication
Latest Publications
- Open Access
- 29 August 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (3) , 035423
Impact of sintering conditions on solderability and wire bondability of thick-film metallizations for Silicon-Ceramic composite substrates
An innovative Silicon-Ceramic (SiCer) composite system enables the combination of Micro-Electro-Mechanical-Systems (MEMS) and Low Temperature Cofired Ceramic (LTCC) technology through a sintering process. The sintering procedure and the sintering temperature are crucial for subsequent processes such as advanced packaging and assembly technologies. Various sintering profiles with different temperatures and heating rates are investigated. The bond interfaces of the manufactured SiCer substrates are evaluated by ultrasonic microscopy. Assembly technologies such as soldering and gold wire bonding are used to evaluate the influence of sintering temperatures on each metallization. Destructive testing methods are carried out to analyze the adhesion, soldered components are sheared off and the wire bonds are pulled. An influence of the sintering temperature on the quality of the bond interface has been proven through this study. The quantity and quality at the SiCer bond interface has been significantly improved and an optimized sintering profile has been established for different metallizations intended for soldering and wire bonding applications.
- 29 August 2025
- Published by IOP Publishing in Engineering Research Express
- Vol. 7 (3) , 035423
Open AccessImpact of sintering conditions on solderability and wire bondability of thick-film metallizations for Silicon-Ceramic composite substrates
An innovative Silicon-Ceramic (SiCer) composite system enables the combination of Micro-Electro-Mechanical-Systems (MEMS) and Low Temperature Cofired Ceramic (LTCC) technology through a sintering process. The sintering procedure and the sintering temperature are crucial for subsequent processes such as advanced packaging and assembly technologies. Various sintering profiles with different temperatures and heating rates are investigated. The bond interfaces of the manufactured SiCer substrates are evaluated by ultrasonic microscopy. Assembly technologies such as soldering and gold wire bonding are used to evaluate the influence of sintering temperatures on each metallization. Destructive testing methods are carried out to analyze the adhesion, soldered components are sheared off and the wire bonds are pulled. An influence of the sintering temperature on the quality of the bond interface has been proven through this study. The quantity and quality at the SiCer bond interface has been significantly improved and an optimized sintering profile has been established for different metallizations intended for soldering and wire bonding applications.
- Open Access
- 2 July 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (8)
Ontology‐Based Data Acquisition, Refinement, and Utilization in the Development of a Multilayer Ferrite Inductor
A key aspect in the development of multilayer inductors is the magnetic permeability of the ferrite layers. Herein, the effects of different processing steps on the permeability of a NiCuZn ferrite are investigated. Dry‐pressed, tape‐cast, and cofired multilayer samples are analyzed. An automated data pipeline is applied to structure the acquired experimental data according to a domain ontology based on Platform MaterialDigital core ontology. Example queries to the ontology show how the determined process–property correlations are accessible to nonexperts and thus how suitable data for component design can be identified. It is demonstrated how the inductance of cofired multilayer inductors is reliably predicted by simulations if the appropriate input data corresponding to the manufacturing process is used.
- 2 July 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (8)
Open AccessOntology‐Based Data Acquisition, Refinement, and Utilization in the Development of a Multilayer Ferrite Inductor
A key aspect in the development of multilayer inductors is the magnetic permeability of the ferrite layers. Herein, the effects of different processing steps on the permeability of a NiCuZn ferrite are investigated. Dry‐pressed, tape‐cast, and cofired multilayer samples are analyzed. An automated data pipeline is applied to structure the acquired experimental data according to a domain ontology based on Platform MaterialDigital core ontology. Example queries to the ontology show how the determined process–property correlations are accessible to nonexperts and thus how suitable data for component design can be identified. It is demonstrated how the inductance of cofired multilayer inductors is reliably predicted by simulations if the appropriate input data corresponding to the manufacturing process is used.
- 15 December 2015
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 13 (3) , 540-548
Integration of High‐Frequency M‐Type Hexagonal Ferrite Inductors in LTCC Multilayer Modules
Monolithic hexagonal BaCo1,3Ti1,3Fe9,4O19 ferrite multilayers sintered at 900°C exhibit a fine‐grained microstructure with permeability of μ′ = 16 and a resonance frequency fr ≥ 1GHz. Co‐firing of hetero‐laminates of ferrite with CT700 glass–ceramic LTCC tapes and with polycrystalline zinc titanate (ZT) LTCC tapes was studied. Co‐firing at 900°C of ferrite/CT700 leads to multilayers with cracks caused by substantial thermal expansion mismatch. Co‐fired ferrite/ZT multilayer laminates exhibit a permeability of μ′ = 16 and do not show any defects. Hexagonal ferrite multilayer inductor elements were integrated into ZT‐based multilayer LTCC modules and co‐fired at 900°C with Ag metallization.
- 15 December 2015
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 13 (3) , 540-548
Integration of High‐Frequency M‐Type Hexagonal Ferrite Inductors in LTCC Multilayer Modules
Monolithic hexagonal BaCo1,3Ti1,3Fe9,4O19 ferrite multilayers sintered at 900°C exhibit a fine‐grained microstructure with permeability of μ′ = 16 and a resonance frequency fr ≥ 1GHz. Co‐firing of hetero‐laminates of ferrite with CT700 glass–ceramic LTCC tapes and with polycrystalline zinc titanate (ZT) LTCC tapes was studied. Co‐firing at 900°C of ferrite/CT700 leads to multilayers with cracks caused by substantial thermal expansion mismatch. Co‐fired ferrite/ZT multilayer laminates exhibit a permeability of μ′ = 16 and do not show any defects. Hexagonal ferrite multilayer inductor elements were integrated into ZT‐based multilayer LTCC modules and co‐fired at 900°C with Ag metallization.
- 1 October 2015
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 35 (11) , 3043-3049
Integration of CaCu3Ti4O12 capacitors into LTCC multilayer modules
- 1 October 2015
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 35 (11) , 3043-3049
Integration of CaCu3Ti4O12 capacitors into LTCC multilayer modules
- 30 September 2014
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 98 (1) , 141-147
Microstructure and Electric Properties of CaCu 3 Ti 4 O 12 Multilayer Capacitors
In a three‐step development process CaCu 3 Ti 4 O 12 ‐based bulk ceramic pellets, tape‐casted multilayer ceramic laminates, and multilayer ceramic capacitors with cofired electrodes were fabricated. The sintering behavior, microstructure, electrical resistivity, and dielectric properties were studied. At a firing temperature of 1050°C, an effective permittivity of about ε′ = 60 000 and 10 000 was observed for sintered pellets and multilayer laminates, respectively. The typical grain growth observed in pellets is suppressed in multilayer laminates. Impedance spectroscopy was employed to show that the bulk grain resistivity is similar in pellets and multilayer laminates, but the grain‐boundary resistivity is higher in pellets. Tapes were processed into multilayer capacitors with Ag / Pd electrodes and cofired at 1050°C. All three types of samples, pellets, laminates, and capacitors were also processed with a glass additive, in which case they can be cofired at a lower temperature of 900°C. In glass‐containing pellets, the temperature dependence of permittivity is weak and exhibits X7R characteristics for frequencies below ≈ 60 kHz. Our results demonstrate the high potential of CaCu 3 Ti 4 O 12 for application in monolithic as well as in integrated multilayer capacitors.
- 30 September 2014
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 98 (1) , 141-147
Microstructure and Electric Properties of CaCu 3 Ti 4 O 12 Multilayer Capacitors
In a three‐step development process CaCu 3 Ti 4 O 12 ‐based bulk ceramic pellets, tape‐casted multilayer ceramic laminates, and multilayer ceramic capacitors with cofired electrodes were fabricated. The sintering behavior, microstructure, electrical resistivity, and dielectric properties were studied. At a firing temperature of 1050°C, an effective permittivity of about ε′ = 60 000 and 10 000 was observed for sintered pellets and multilayer laminates, respectively. The typical grain growth observed in pellets is suppressed in multilayer laminates. Impedance spectroscopy was employed to show that the bulk grain resistivity is similar in pellets and multilayer laminates, but the grain‐boundary resistivity is higher in pellets. Tapes were processed into multilayer capacitors with Ag / Pd electrodes and cofired at 1050°C. All three types of samples, pellets, laminates, and capacitors were also processed with a glass additive, in which case they can be cofired at a lower temperature of 900°C. In glass‐containing pellets, the temperature dependence of permittivity is weak and exhibits X7R characteristics for frequencies below ≈ 60 kHz. Our results demonstrate the high potential of CaCu 3 Ti 4 O 12 for application in monolithic as well as in integrated multilayer capacitors.
- Open Access
- 1 January 2014
- Published by Japan Society of Powder and Powder Metallurgy in Journal of the Japan Society of Powder and Powder Metallurgy
- Vol. 61 (S1) , S214-S217
Integration of Ni-Cu-Zn and Hexagonal Ferrites into LTCC Modules: Cofiring Strategies and Magnetic Properties
We have studied the integration of Ni-Cu-Zn ferrite spinels as well as substituted hexagonal Co2Y-and M-type ferrites into LTCC (Low Temperature Ceramic Co-firing) modules. The cofiring behavior and the magnetic properties of these materials were investigated and evaluated for multilayer applications. Ni-Cu-Zn ferrites exhibit permeabilities of μ=300–500 for operating frequencies in the MHz range. Cu-substituted Y-type ferrites Ba2Co2-x-yZnxCuyFe12O22 in combination with sintering additives display sufficient shrinkage and densification at 900°C. A permeability of μ=10 is observed; however, substituted Co2Y-type ferrites do not exhibit long-term stability at 900°C. Co/Ti-substituted M-type ferrites BaFe12-2yCoyTiyO19 (y=1.2) with planar magneto-crystalline anisotropy exhibit excellent soft magnetic behavior. Using sintering additives, complete densification is reached at 900°C and a permeability of μ=15 and a resonance frequency of larger than 1 GHz are observed. Integration of ferrite multilayer inductor components into LTCC modules using free and constrained cofiring technologies is demonstrated.
- 1 January 2014
- Published by Japan Society of Powder and Powder Metallurgy in Journal of the Japan Society of Powder and Powder Metallurgy
- Vol. 61 (S1) , S214-S217
Open AccessIntegration of Ni-Cu-Zn and Hexagonal Ferrites into LTCC Modules: Cofiring Strategies and Magnetic Properties
We have studied the integration of Ni-Cu-Zn ferrite spinels as well as substituted hexagonal Co2Y-and M-type ferrites into LTCC (Low Temperature Ceramic Co-firing) modules. The cofiring behavior and the magnetic properties of these materials were investigated and evaluated for multilayer applications. Ni-Cu-Zn ferrites exhibit permeabilities of μ=300–500 for operating frequencies in the MHz range. Cu-substituted Y-type ferrites Ba2Co2-x-yZnxCuyFe12O22 in combination with sintering additives display sufficient shrinkage and densification at 900°C. A permeability of μ=10 is observed; however, substituted Co2Y-type ferrites do not exhibit long-term stability at 900°C. Co/Ti-substituted M-type ferrites BaFe12-2yCoyTiyO19 (y=1.2) with planar magneto-crystalline anisotropy exhibit excellent soft magnetic behavior. Using sintering additives, complete densification is reached at 900°C and a permeability of μ=15 and a resonance frequency of larger than 1 GHz are observed. Integration of ferrite multilayer inductor components into LTCC modules using free and constrained cofiring technologies is demonstrated.