Xianqing Yin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xianqing Yin has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Mengying Yang
College of Chemical and Environmental Engineering; Yangtze University; Jingzhou 434023 China
2 shared publications- Mijia Zhu
College of Chemistry and Environmental Engineering, Yangtze University, Jingzhou, China
2 shared publications Wenjuan Chen
State Key Laboratory of Offshore Oil Exploitation and CNOOC Research Institute; Beijing 100027 China
2 shared publicationsBo Jing
State Key Laboratory of Offshore Oil Exploitation and CNOOC Research Institute; Beijing 100027 China
1 shared publication- Bo Jing
State Key Laboratory of Offshore Oil Exploitation, Beijing 100027, China; CNOOC Research Institute, Beijing 100027, China
1 shared publication - Jun Yao
College of Water Resources and Environment, China University of Geosciences (Beijing), Beijing 100083, China
1 shared publication
Latest Publications
- 31 March 2020
- Published by HARD Publishing Company in Polish Journal of Environmental Studies
- Vol. 29 (3) , 2493-2502
Optimization and Modelling Using the Response Surface Methodology for Methylene Blue Removal by Electrocoagulation/Hazelnut Shell Adsorption Coupling in a Batch System
The present work examined the removal of methylene blue (MB) from aqueous solutions through an electrocoagulation/hazelnut shell (EC/HNS) adsorption coupling process. The process was evaluated using a Box–Behnken design (BBD) under the response surface methodology (RSM). According to the obtained results from BBD–RSM regression analysis, we found that the experimental data are best fitted to the second-order polynomial model with coefficient of determination (R2) value of 0.9534, adjust coefficient (Radj 2) value of 0.9926 and predicted correlation coefficient (RPred 2) value of 0.9973. The maximum MB removal efficiency was obtained under optimized conditions (HNS dosage, 6 g/L; reaction time, 17.75 min; and current density, 2.6 mA/cm2). Under the optimum conditions, the MB removal rate reached 99.45%, and the RSM predictive value was 98.71% with a small deviation. These results confirmed that the RSM model accurately and reliably analysed the process of removing MB from wastewater.
- 31 March 2020
- Published by HARD Publishing Company in Polish Journal of Environmental Studies
- Vol. 29 (3) , 2493-2502
Optimization and Modelling Using the Response Surface Methodology for Methylene Blue Removal by Electrocoagulation/Hazelnut Shell Adsorption Coupling in a Batch System
The present work examined the removal of methylene blue (MB) from aqueous solutions through an electrocoagulation/hazelnut shell (EC/HNS) adsorption coupling process. The process was evaluated using a Box–Behnken design (BBD) under the response surface methodology (RSM). According to the obtained results from BBD–RSM regression analysis, we found that the experimental data are best fitted to the second-order polynomial model with coefficient of determination (R2) value of 0.9534, adjust coefficient (Radj 2) value of 0.9926 and predicted correlation coefficient (RPred 2) value of 0.9973. The maximum MB removal efficiency was obtained under optimized conditions (HNS dosage, 6 g/L; reaction time, 17.75 min; and current density, 2.6 mA/cm2). Under the optimum conditions, the MB removal rate reached 99.45%, and the RSM predictive value was 98.71% with a small deviation. These results confirmed that the RSM model accurately and reliably analysed the process of removing MB from wastewater.
- 17 November 2016
- Published by Wiley in Journal of the Chinese Chemical Society
- Vol. 64 (1) , 73-79
Experimental Study on COD Composition and Electrochemical Degradation of Wastewater in Offshore Oilfields
- 17 November 2016
- Published by Wiley in Journal of the Chinese Chemical Society
- Vol. 64 (1) , 73-79
Experimental Study on COD Composition and Electrochemical Degradation of Wastewater in Offshore Oilfields
- Open Access
- 1 July 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (33) , 15314-15325
Using response surface methodology to evaluate electrocoagulation in the pretreatment of produced water from polymer-flooding well of Dagang Oilfield with bipolar aluminum electrodes
The wide use of polymers to enhance oil recovery can make pumping and rejecting oilfield produced water difficult because of the high viscosity of the treated water. To deal with this problem, this study proposed an electrocoagulation method that is time saving, highly efficient, and easy to apply. A Box–Behnken design coupled with the response surface methodology (RSM) was used to construct a model of the electrocoagulation process that considers three key variables: current density, inter-electrode gap, and operation time. The optimized operational conditions were obtained using second-order polynomial models; they were a current density of 45.6 mA/cm2, an inter-electrode of 3.2 cm, and an operation time of 22.8 min. The results under these conditions were a viscosity reduction of 90.9% and a chemical oxygen demand (COD) reduction of 74.9%. These data strongly correlated with the predicted values of the RSM models. Based on the single and interactive effect analysis, it showed that viscosity and COD reduction efficiency enhanced with increasing operation time. The efficiencies were increased when current density was raised from 20 to 40 mA/cm2 and subsequently decreased from 40 to 60 mA/cm2. They were also increased while inter-electrode gap was enlarged from 2.0 to 4.0 cm and then decreased from 4.0 to 6.0 cm. Furthermore, the practicability of the polymer-flooding produced water treatment under the optimized conditions was proved by UV–vis, zeta potential, and particle size measurement.
- 1 July 2016
- Published by Elsevier in Desalination and Water Treatment
- Vol. 57 (33) , 15314-15325
Open AccessUsing response surface methodology to evaluate electrocoagulation in the pretreatment of produced water from polymer-flooding well of Dagang Oilfield with bipolar aluminum electrodes
The wide use of polymers to enhance oil recovery can make pumping and rejecting oilfield produced water difficult because of the high viscosity of the treated water. To deal with this problem, this study proposed an electrocoagulation method that is time saving, highly efficient, and easy to apply. A Box–Behnken design coupled with the response surface methodology (RSM) was used to construct a model of the electrocoagulation process that considers three key variables: current density, inter-electrode gap, and operation time. The optimized operational conditions were obtained using second-order polynomial models; they were a current density of 45.6 mA/cm2, an inter-electrode of 3.2 cm, and an operation time of 22.8 min. The results under these conditions were a viscosity reduction of 90.9% and a chemical oxygen demand (COD) reduction of 74.9%. These data strongly correlated with the predicted values of the RSM models. Based on the single and interactive effect analysis, it showed that viscosity and COD reduction efficiency enhanced with increasing operation time. The efficiencies were increased when current density was raised from 20 to 40 mA/cm2 and subsequently decreased from 40 to 60 mA/cm2. They were also increased while inter-electrode gap was enlarged from 2.0 to 4.0 cm and then decreased from 4.0 to 6.0 cm. Furthermore, the practicability of the polymer-flooding produced water treatment under the optimized conditions was proved by UV–vis, zeta potential, and particle size measurement.
- Open Access
- 1 January 2016
- Published by Atlantis Press SARL
Experimental Study on COD Composition and Electrochemical Degradation of Wastewater in Offshore Oilfields
- 1 January 2016
- Published by Atlantis Press SARL
Open AccessExperimental Study on COD Composition and Electrochemical Degradation of Wastewater in Offshore Oilfields