Junliang Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Junliang Li has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Zhongliang Zhan
CAS Key Laboratory of Materials for Energy Conversion, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050, China
3 shared publications C. Zhong
The Key Laboratory of Energy Conversion Materials, Shanghai Institute of Ceramics, Chinese Academy of Sciences, 1295 Dingxi Road, Shanghai 200050, P. R. China
1 shared publicationH. Nie
The Key Laboratory of Energy Conversion Materials, Shanghai Institute of Ceramics, Chinese Academy of Sciences, 1295 Dingxi Road, Shanghai 200050, P. R. China
1 shared publicationH. Wu
The Key Laboratory of Energy Conversion Materials, Shanghai Institute of Ceramics, Chinese Academy of Sciences, 1295 Dingxi Road, Shanghai 200050, P. R. China
1 shared publicationHuaiwen Nie
Chinese Academy of Sciences
1 shared publicationJian Shi
Chinese Academy of Sciences
1 shared publication
Latest Publications
- Open Access
Potentiometric NO2 Sensors Based on Thin Stabilized Zirconia Electrolytes and Asymmetric (La0.8Sr0.2)0.95MnO3 Electrodes
Here we report on a new architecture for potentiometric NO2 sensors that features thin 8YSZ electrolytes sandwiched between two porous (La0.8Sr0.2)0.95MnO3 (LSM95) layers—one thick and the other thin—fabricated by the tape casting and co-firing techniques. Measurements of their sensing characteristics show that reducing the porosity of the supporting LSM95 reference electrodes can increase the response voltages. In the meanwhile, thin LSM95 layers perform better than Pt as the sensing electrode since the former can provide higher response voltages and better linear relationship between the sensitivities and the NO2 concentrations over 40–1000 ppm. The best linear coefficient can be as high as 0.99 with a sensitivity value of 52 mV/decade as obtained at 500 °C. Analysis of the sensing mechanism suggests that the gas phase reactions within the porous LSM95 layers are critically important in determining the response voltages.
Open AccessPotentiometric NO2 Sensors Based on Thin Stabilized Zirconia Electrolytes and Asymmetric (La0.8Sr0.2)0.95MnO3 Electrodes
Here we report on a new architecture for potentiometric NO2 sensors that features thin 8YSZ electrolytes sandwiched between two porous (La0.8Sr0.2)0.95MnO3 (LSM95) layers—one thick and the other thin—fabricated by the tape casting and co-firing techniques. Measurements of their sensing characteristics show that reducing the porosity of the supporting LSM95 reference electrodes can increase the response voltages. In the meanwhile, thin LSM95 layers perform better than Pt as the sensing electrode since the former can provide higher response voltages and better linear relationship between the sensitivities and the NO2 concentrations over 40–1000 ppm. The best linear coefficient can be as high as 0.99 with a sensitivity value of 52 mV/decade as obtained at 500 °C. Analysis of the sensing mechanism suggests that the gas phase reactions within the porous LSM95 layers are critically important in determining the response voltages.
- 28 October 2014
- Published by Wiley in Fuel Cells
- Vol. 14 (6) , 1046-1049
Sr2Fe1.5Mo0.5O6–δ – Zr0.84Y0.16O2–δ Materials as Oxygen Electrodes for Solid Oxide Electrolysis Cells
The high‐temperature solid oxide electrolysis cell (SOEC) is one of the most promising devices for hydrogen mass production. To make SOEC suitable from an economical point of view, each component of the SOEC has to be optimized. At this level, the optimization of the oxygen electrode is of particular interest since it contributes to a large extent to the cell polarization resistance. The present paper is focused on an alternative oxygen electrode of Zr0.84Y0.16O2–δ‐Sr2Fe1.5Mo0.5O6–δ (YSZ‐SFM). YSZ‐SFM composite oxygen electrodes were fabricated by impregnating the YSZ matrix with SFM, and the ion‐impregnated YSZ‐SFM composite oxygen electrodes showed excellent performance. For a voltage of 1.2 V, the electrolysis current was 223 mA cm−2, 327 mA cm−2 and 310 mA cm−2 at 750 °C for the YSZ‐SFM10, YSZ‐SFM20, and YSZ‐SFM30 oxygen electrode, respectively. A hydrogen production rate as high as 11.46 NL h−1 has been achieved for the SOEC with the YSZ‐SFM20 electrode at 750 °C. The results demonstrate that YSZ‐SFM fabricated by impregnating the YSZ matrix with SFM is a promising composite electrode for the SOEC.
- 28 October 2014
- Published by Wiley in Fuel Cells
- Vol. 14 (6) , 1046-1049
Sr2Fe1.5Mo0.5O6–δ – Zr0.84Y0.16O2–δ Materials as Oxygen Electrodes for Solid Oxide Electrolysis Cells
The high‐temperature solid oxide electrolysis cell (SOEC) is one of the most promising devices for hydrogen mass production. To make SOEC suitable from an economical point of view, each component of the SOEC has to be optimized. At this level, the optimization of the oxygen electrode is of particular interest since it contributes to a large extent to the cell polarization resistance. The present paper is focused on an alternative oxygen electrode of Zr0.84Y0.16O2–δ‐Sr2Fe1.5Mo0.5O6–δ (YSZ‐SFM). YSZ‐SFM composite oxygen electrodes were fabricated by impregnating the YSZ matrix with SFM, and the ion‐impregnated YSZ‐SFM composite oxygen electrodes showed excellent performance. For a voltage of 1.2 V, the electrolysis current was 223 mA cm−2, 327 mA cm−2 and 310 mA cm−2 at 750 °C for the YSZ‐SFM10, YSZ‐SFM20, and YSZ‐SFM30 oxygen electrode, respectively. A hydrogen production rate as high as 11.46 NL h−1 has been achieved for the SOEC with the YSZ‐SFM20 electrode at 750 °C. The results demonstrate that YSZ‐SFM fabricated by impregnating the YSZ matrix with SFM is a promising composite electrode for the SOEC.
- 22 March 2014
- Published by Springer Nature in Journal of Electroceramics
- Vol. 32 (4) , 339-343
Improvement of a GDC-based composite cathode for intermediate-temperature solid oxide fuel cells
- 22 March 2014
- Published by Springer Nature in Journal of Electroceramics
- Vol. 32 (4) , 339-343
Improvement of a GDC-based composite cathode for intermediate-temperature solid oxide fuel cells