VBViorel Branzoi

Viorel Branzoi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Viorel Branzoi has a total of 6 co-authors. Here are the top co-authors by number of shared publications:

  • Florina Branzoi

    Institute of Physical Chemistry-Ilie Murgulescu, 202 Splaiul Independenţei, 060021 Bucharest, Romania

    5 shared publications
  • Ancuta Musina

    Department of Applied Physical Chemistry and Electrochemistry University Politehnica of Bucharest 132 Calea Griviţei 010737 Bucharest Romania

    2 shared publications
  • Luisa Pilan

    Department of Inorganic Chemistry, Physical Chemistry and Electrochemistry, University Politehnica of Bucharest, Gh Polizu 1-7, 011061 Bucharest, Romania

    2 shared publications
  • Alina Pruna

    Institute of Materials Technology, Universitat Politècnica de València, 46022 Valencia, Spain

    1 shared publication
  • C. Licu

    University Politehnica of Bucharest; 132 Calea Griviţei Bucharest (Romania)

    1 shared publication
  • Florentina Golgovici

    Faculty of Industrial Chemistry, Department of Physical Chemistry and Electrochemistry , University “Politehnica” of Bucharest , Calea Griviţei, Bucharest, Romania

    1 shared publication

Latest Publications

  • Fabrication and characterisation of conducting composite films based on conducting polymers and functionalised carbon nanotubes

    by Florina Branzoi, Viorel Branzoi, Ancuta Musina

    Electropolymerisation and characterisation of polyaniline film doped with functionalised single‐wall carbon nanotubes and different dopants were studied. These nanoporous composite films were grown electrochemically from aqueous solutions such that constituents were deposited simultaneously onto substrate electrode. The synthetic, morphological and electrical properties of obtained nanocomposite films were compared. SEM revealed that the composite films consisted of nanoporous networks of single‐wall carbon nanotubes coated with polymeric film. Cyclic voltammetry and electrochemical impedance spectroscopy demonstrated that these composite films had similar electrochemical response rates to pure polymeric films but a lower resistance and much improved mechanical integrity. The negatively charged functionalised carbon nanotubes served as anionic dopant during the electropolymerisation to synthesize polymer/functionalised carbon nanotube composite films. The specific electrochemical capacitance of the composite films is a significantly greater value than that for pure polymer films prepared similarly. Using these composite films, the modified electrodes with improved properties were obtained. Copyright © 2012 John Wiley & Sons, Ltd.


  • Amperometric urea biosensor based on platinum electrode modified with a nanocomposite film

    by Florina Branzoi, Viorel Branzoi, Ancuta Musina

    A novel amperometric biosensor for the detection of urea was prepared by immobilizing urease on a modified electrode of nanocomposite film/platinum substrate. The nanocomposite film was obtained by electrochemical co‐polymerization of the corresponding monomers in the presence of functionalized carbon nanotubes and different additives. These nanocomposites were used as conducting films for amperometric urea sensing after covalent immobilization of urease onto nanocomposite‐coated electrodes. The electrochemical performance of the modified electrode was studied by cyclic voltammetry, chronoamperometry and scanning electron microscopy. The immobilized urease on the nanocomposite film surface exhibited an excellent electrocatalytic response toward the reduction of urea. Amperometric response was measured as a function of urea concentration at a fixed potential, in this case, the open circuit potential. The obtained sensor showed rapid response and good reversibility. The response time was less than 10 s, whereas the reversible time was approximately 5 to 15 s. The enzymatic nanostructured electrode exhibited high sensitivity, a wide linear range and low detection limit for the electrochemical detection of urea. Copyright © 2012 John Wiley & Sons, Ltd.


  • Electrosynthesized Doped Polypyrrole Films on Pure Zinc Electrode

    by V. Brânzoi, A. Prună, F. Brânzoi

    Polypyrrole films have been successfully synthesized on zinc surface in absence and presence of sodium bis(2-ethylhexyl) sulfosuccinate and sodium dodecylbenzosulphonate as dopants. The synthesis was achieved by galvanostatic method. The electrochemical behaviour of doped-polypyrrole films was investigated by electrochemical impedance spectroscopy and polarization studies. The films were characterized by scanning electron microscopy. Considering the surfactant anions entrapment inside the polymer matrix, the obtained results showed that the dopant concentration plays an important role in the response of the obtained coatings which proved to inhibit the corrosion of zinc substrate at anodic polarization in 0.1 M NaCl.


  • Electropolymerization Compounds Used for the Obtainment of Modified Electrodes and Electrochemical Biosensors

    by V. Brânzoi, Luisa Pilan

    Modified electrodes were obtained from pyrrole and aniline on different substrates like: platinum, titanium, zinc or aluminium substrates by electropolymerization or by co-electropolymerization from synthesis solutions containing different ratio of monomers. Cyclic voltammetry and electrochemical impedance spectroscopy were used to investigate the electrochemical properties of the resulting modified electrodes. Further, an amperometric biosensor for glucose was prepared by immobilization of glucose-oxidase into a poly(o-phenylenediamine) film by simple one-step electropolymerization on platinum substrate. The rejection of interference species may be additionally increased by placing additional layers of Prussian Blue that ensured electrode operation at low potential values or of polypyrrole, respectively.


  • Electrochemical Activity and Corrosion Protection Properties of Doped Polypyrrole Electrodeposited at Pure Aluminium Electrode

    by V. Brânzoi, Luisa Pilan, Florentina Golgovici, Florina Brânzoi

    Polypyrrole films were electrodeposited at pure aluminium from aqueous solution of sodium sulphate containing pyrrole and organic compounds as dopants. Substrate-adherent polypyrrole films were obtained by electrochemical oxidation of pyrrole using the potentiodynamic method and cycling the electrode potential from 50 up to 100 cycles on the potential range of 0 ÷ 800 mV. Since the conducting polymers, such as polypyrrole, are electrosynthesized easily at inert electrodes such as gold and platinum, but much more difficult at aluminium electrodes, the surface protective oxide, Al2O3, was removed, as it acts as a barrier inhibiting electron transfer and the polymerization process. The electrochemical properties of polypyrrole films electrosynthesized from aqueous solutions containing sodium dodecylsulphate (SDS) and sodium bis(2-ethylhexyl) sulfosuccinate (AOT) as doping electrolytes were studied by cyclic voltammetry and electrochemical impedance spectroscopy. The results indicate that the mechanism of the redox process is complex and may be governed by the diffusion of the electrolyte. The cyclic voltammograms of polypyrrole film synthesized in solutions having different concentrations of SDS and AOT indicate that the dopant concentration plays a very relevant role in the electrochemical response of the doped polypyrrole films like as: PPY/SDS/aluminium oxide and PPY/AOT/aluminium oxide. The results indicate that the SDS and AOT anions favor redox processes which are faster and more reversible than those associated to usual polypyrrole electrodes. However, the aluminium substrate had a considerable effect on the electrochemical activity of the polypyrrole films and that, because in the presence of pyrrole, anodization of these electrolytes resulted in formation of Al2O3 and PPY layers simultaneously. This is consistent with a galvanic interaction between the polymer and the aluminium substrate, giving rise to oxidation of the aluminium and reduction of the polymer. The corrosion performance of polypyrrole coated aluminium was evaluated by DC polarization and Electrochemical Impedance Spectroscopy. Our results show that the presence of polypyrrole coatings significantly increases the corrosion potential and drastically reduces the corrosion current and corrosion rate of pure aluminium. The corrosion resistance of polypyrrole coated aluminium was higher than of uncoated aluminium.