Zhen Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhen Sun has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Yun Yang
Nanyang Technological University
8 shared publications - Kaiyuan Wang
School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore
4 shared publications Fei Qiu
3 shared publicationsHuiping Li
3 shared publications- Yao Wang
Department of Electrical and Computer Engineering, Drexel University, Philadelphia, PA, USA
3 shared publications - Junming Zeng
School of Electrical and Electronic Engineering, Nanyang Technological University, Singapore
2 shared publications
Latest Publications
- 6 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (9) , 16658-16671
Optimized Stacked Passive Coil Array Design for High Efficiency and Misalignment Tolerance in PCB-Based Wireless Power Transfer Systems
This paper presents a stacked passive coil array (SPCA) integrated on the transmitter (Tx) side to enhance power transfer efficiency (PTE), power delivered to the load (PDL), and misalignment tolerance in printed circuit board (PCB)-based wireless power transfer (WPT) systems. Power losses in the PCB coils are analyzed, and a modified multi-objective genetic algorithm (GA) is employed to optimize key geometric parameters for simultaneous improvement in PTE and PDL. An equivalent circuit model is developed to quantify the influence of SPCA design factors, including the number of units and their resonant frequencies. A unified parameter design strategy for both the SPCA and compensation network is also proposed to achieve optimal system performance. Experimental validation using a 200 kHz, 160 W prototype demonstrates a 10.5% enhancement in DC–DC PTE at a 120 mm transfer distance, comparable to ferrite-based systems, while achieving a 6.55-fold increase in PDL. The performance surpasses that of both the planar passive coil array (PPCA) and the nanocrystalline ribbon core (NRC) based configurations under identical operating conditions. The SPCA-based system further exhibits superior robustness under lateral misalignment conditions.
- 6 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 41 (9) , 16658-16671
Optimized Stacked Passive Coil Array Design for High Efficiency and Misalignment Tolerance in PCB-Based Wireless Power Transfer Systems
This paper presents a stacked passive coil array (SPCA) integrated on the transmitter (Tx) side to enhance power transfer efficiency (PTE), power delivered to the load (PDL), and misalignment tolerance in printed circuit board (PCB)-based wireless power transfer (WPT) systems. Power losses in the PCB coils are analyzed, and a modified multi-objective genetic algorithm (GA) is employed to optimize key geometric parameters for simultaneous improvement in PTE and PDL. An equivalent circuit model is developed to quantify the influence of SPCA design factors, including the number of units and their resonant frequencies. A unified parameter design strategy for both the SPCA and compensation network is also proposed to achieve optimal system performance. Experimental validation using a 200 kHz, 160 W prototype demonstrates a 10.5% enhancement in DC–DC PTE at a 120 mm transfer distance, comparable to ferrite-based systems, while achieving a 6.55-fold increase in PDL. The performance surpasses that of both the planar passive coil array (PPCA) and the nanocrystalline ribbon core (NRC) based configurations under identical operating conditions. The SPCA-based system further exhibits superior robustness under lateral misalignment conditions.
- 9 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Implementation of a 4.8 kW 8-GaN-HEMT H-Bridge Inverter with ZVS for 6.78 MHz Wireless Power Transfer Systems
This paper presents a 6.78 MHz, 4.8 kW H-bridge inverter employing parallel 650 V gallium nitride (GaN) high-electron-mobility transistors (HEMTs) and an auxiliary inductor to achieve zero-voltage switching (ZVS) for next-generation wireless power transfer (WPT) systems with a wide load range. An energy-based analytical framework is developed to define the ZVS operating region as a function of the inverter output current and load-impedance phase angle. The auxiliary circuit compensates for the increased output capacitance caused by device paralleling, thereby preserving ZVS conditions and enabling high-efficiency operation. To validate the analysis, both 4-GaN-HEMT and 8-GaN-HEMT inverter prototypes are designed and experimentally compared. The proposed 8-GaN-HEMT inverter achieves a maximum output power of 4.8 kW at 500 V, outperforming the 4-GaN-HEMT inverter’s 2.8 kW limit at 400 V, and demonstrates a wider ZVS range. The results confirm that both inverters can effectively drive a typical series-series (SS)-compensated WPT system at 6.78 MHz, achieving power levels exceeding the state-of-the-art 2.5 kW.
- 9 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Implementation of a 4.8 kW 8-GaN-HEMT H-Bridge Inverter with ZVS for 6.78 MHz Wireless Power Transfer Systems
This paper presents a 6.78 MHz, 4.8 kW H-bridge inverter employing parallel 650 V gallium nitride (GaN) high-electron-mobility transistors (HEMTs) and an auxiliary inductor to achieve zero-voltage switching (ZVS) for next-generation wireless power transfer (WPT) systems with a wide load range. An energy-based analytical framework is developed to define the ZVS operating region as a function of the inverter output current and load-impedance phase angle. The auxiliary circuit compensates for the increased output capacitance caused by device paralleling, thereby preserving ZVS conditions and enabling high-efficiency operation. To validate the analysis, both 4-GaN-HEMT and 8-GaN-HEMT inverter prototypes are designed and experimentally compared. The proposed 8-GaN-HEMT inverter achieves a maximum output power of 4.8 kW at 500 V, outperforming the 4-GaN-HEMT inverter’s 2.8 kW limit at 400 V, and demonstrates a wider ZVS range. The results confirm that both inverters can effectively drive a typical series-series (SS)-compensated WPT system at 6.78 MHz, achieving power levels exceeding the state-of-the-art 2.5 kW.
- 21 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 62 (1) , 1564-1572
A Resonant-Frequency-Based Dynamic Front-End Monitoring Strategy for Series-Series-Compensated Inductive Power Transfer Systems Without Communication
Front-end monitoring of coupling and load conditions is vital for next-generation inductive power transfer (IPT) systems, especially with the shift to new control paradigms. Existing monitoring schemes often face challenges such as non-resonant frequency identification, low accuracy, extensive data measurement requirements, and limited operating conditions. To tackle these issues, this paper proposes a resonant-frequency-based dynamic front-end monitoring strategy for typical series-series (SS)-compensated IPT systems. This method is grounded in the small-signal model of the SS-compensated IPT system, allowing for the estimation of mutual inductance and load conditions based solely on the dynamic responses of the transmitter-side current, without requiring communication feedback from the receiver. A key advantage of this strategy is its ability to accurately and rapidly determine mutual inductance and load conditions at resonant frequency during the initial soft starting phase. Both simulation and experimental results demonstrate the superior performance of the proposed monitoring strategy compared to conventional non-resonant frequency-based steady-state methods.
- 21 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 62 (1) , 1564-1572
A Resonant-Frequency-Based Dynamic Front-End Monitoring Strategy for Series-Series-Compensated Inductive Power Transfer Systems Without Communication
Front-end monitoring of coupling and load conditions is vital for next-generation inductive power transfer (IPT) systems, especially with the shift to new control paradigms. Existing monitoring schemes often face challenges such as non-resonant frequency identification, low accuracy, extensive data measurement requirements, and limited operating conditions. To tackle these issues, this paper proposes a resonant-frequency-based dynamic front-end monitoring strategy for typical series-series (SS)-compensated IPT systems. This method is grounded in the small-signal model of the SS-compensated IPT system, allowing for the estimation of mutual inductance and load conditions based solely on the dynamic responses of the transmitter-side current, without requiring communication feedback from the receiver. A key advantage of this strategy is its ability to accurately and rapidly determine mutual inductance and load conditions at resonant frequency during the initial soft starting phase. Both simulation and experimental results demonstrate the superior performance of the proposed monitoring strategy compared to conventional non-resonant frequency-based steady-state methods.
- 20 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 14 (1) , 1244-1256
Communication-Free Rectification Control of SS Inductive EV Charging System for Power Regulatability, Misalignment Tolerance, and Bidirectionality
This paper introduces a communication-free series-series (SS) inductive power transfer (IPT) system designed for electric vehicle (EV) charging, featuring three key advantages: 1) exceptional power regulatability adapting to the charging profiles of EV battery, 2) high tolerance to misalignment, ensuring stable charging power under misaligned conditions, and 3) bidirectional power transfer capability. The phase angle Δθ between the AC output current and voltage is controlled by the proposed vehicle-side active rectifier. With 0≤Δθ<90°, the IPT system works in grid-to-vehicle (G2V) charging mode, and the output current/voltage/power can be monotonously regulated by adjusting Δθ, achieving constant-current (CC) and constant-voltage (CV) charging as well as high misalignment tolerance. With 90°<Δθ≤180°, the IPT system works in vehicle-to-grid (V2G) discharging mode, contributing to bidirectional power transfer. All the functions are achieved by the vehicle-side active rectifier without the involvement of grid-sided converters, consequently removing the dual-sided communication and the front/back-end converters. To validate the proposed design, a 3kW IPT prototype is implemented. Experimental results demonstrate a CC charging limit of 8.1A, a CV charging limit of 400V, and a ±100 mm misalignment tolerance in both x and y directions in G2V mode, and the maximum G2V efficiency achieves 96.9% with 3.02kW at a distance of 180mm (k=0.237). With Δθ=153°, 3kW V2G discharging is verified, and a maximum V2G efficiency of 96.59% with 2.01kW is achieved.
- 20 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 14 (1) , 1244-1256
Communication-Free Rectification Control of SS Inductive EV Charging System for Power Regulatability, Misalignment Tolerance, and Bidirectionality
This paper introduces a communication-free series-series (SS) inductive power transfer (IPT) system designed for electric vehicle (EV) charging, featuring three key advantages: 1) exceptional power regulatability adapting to the charging profiles of EV battery, 2) high tolerance to misalignment, ensuring stable charging power under misaligned conditions, and 3) bidirectional power transfer capability. The phase angle Δθ between the AC output current and voltage is controlled by the proposed vehicle-side active rectifier. With 0≤Δθ<90°, the IPT system works in grid-to-vehicle (G2V) charging mode, and the output current/voltage/power can be monotonously regulated by adjusting Δθ, achieving constant-current (CC) and constant-voltage (CV) charging as well as high misalignment tolerance. With 90°<Δθ≤180°, the IPT system works in vehicle-to-grid (V2G) discharging mode, contributing to bidirectional power transfer. All the functions are achieved by the vehicle-side active rectifier without the involvement of grid-sided converters, consequently removing the dual-sided communication and the front/back-end converters. To validate the proposed design, a 3kW IPT prototype is implemented. Experimental results demonstrate a CC charging limit of 8.1A, a CV charging limit of 400V, and a ±100 mm misalignment tolerance in both x and y directions in G2V mode, and the maximum G2V efficiency achieves 96.9% with 3.02kW at a distance of 180mm (k=0.237). With Δθ=153°, 3kW V2G discharging is verified, and a maximum V2G efficiency of 96.59% with 2.01kW is achieved.
- 3 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (11) , 17469-17487
Challenges and Comparison in Achieving 6.78 MHz Multi-kW H-Bridge DC–AC Inverters Using High-Voltage SiC and GaN Switching Devices
This article investigates the challenges of designing 6.78 MHz multi-kilowatt H-bridge inverters with high-voltage silicon carbide (SiC) and gallium nitride (GaN) devices, while comparing their performance. First, a design methodology for MHz-switching H-bridge inverters is proposed, addressing critical aspects such as switch selection, gate driver supply design, parasitic inductance minimization, zero-voltage switching, and thermal management. Three 1st-generation inverters are then implemented using 650 V wide-bandgap devices: SiC MOSFET (C3M0060065K), GaN field-effect transistor (FET) (TP65H070G4PS), and GaN FET (GS66506T). In multi-MHz and multi-kW testing, the SiC-based inverter reaches a switching limit of 4 MHz at 3.874 kW but suffers from gate driver overpowering and thermal constraints. The TP65H070G4PS GaN inverter achieves the optimal frequency-power balance, delivering 2.026 kW at 6.78 MHz, though it exhibits significant oscillations at low dc voltages (<250 V). Meanwhile, the GS66506T GaN inverter demonstrates superior high-frequency performance but struggles with thermal dissipation, attaining 1.105 kW at 6.78 MHz. To enable reliable 6.78 MHz power conversion, a 2nd-generation design is developed using enhanced SiC (C3M0120100K) and GaN (GS66508T) switches and evaluated in a 6.78-MHz and 2.4-kW isolated dc–dc converter. These inverters achieve 2.448 kW with 93.63% dc–dc efficiency for the SiC inverter, while the GaN variant reaches 2.483 kW at 95.17% efficiency. This marks the first practical demonstration of a multi-kW SiC H-bridge inverter operating at 6.78 MHz and highlights the performance tradeoffs between SiC and GaN technologies.
- 3 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (11) , 17469-17487
Challenges and Comparison in Achieving 6.78 MHz Multi-kW H-Bridge DC–AC Inverters Using High-Voltage SiC and GaN Switching Devices
This article investigates the challenges of designing 6.78 MHz multi-kilowatt H-bridge inverters with high-voltage silicon carbide (SiC) and gallium nitride (GaN) devices, while comparing their performance. First, a design methodology for MHz-switching H-bridge inverters is proposed, addressing critical aspects such as switch selection, gate driver supply design, parasitic inductance minimization, zero-voltage switching, and thermal management. Three 1st-generation inverters are then implemented using 650 V wide-bandgap devices: SiC MOSFET (C3M0060065K), GaN field-effect transistor (FET) (TP65H070G4PS), and GaN FET (GS66506T). In multi-MHz and multi-kW testing, the SiC-based inverter reaches a switching limit of 4 MHz at 3.874 kW but suffers from gate driver overpowering and thermal constraints. The TP65H070G4PS GaN inverter achieves the optimal frequency-power balance, delivering 2.026 kW at 6.78 MHz, though it exhibits significant oscillations at low dc voltages (<250 V). Meanwhile, the GS66506T GaN inverter demonstrates superior high-frequency performance but struggles with thermal dissipation, attaining 1.105 kW at 6.78 MHz. To enable reliable 6.78 MHz power conversion, a 2nd-generation design is developed using enhanced SiC (C3M0120100K) and GaN (GS66508T) switches and evaluated in a 6.78-MHz and 2.4-kW isolated dc–dc converter. These inverters achieve 2.448 kW with 93.63% dc–dc efficiency for the SiC inverter, while the GaN variant reaches 2.483 kW at 95.17% efficiency. This marks the first practical demonstration of a multi-kW SiC H-bridge inverter operating at 6.78 MHz and highlights the performance tradeoffs between SiC and GaN technologies.
- 20 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 62 (1) , 1433-1443
A Robust Artificial Intelligence-Empowered Adaptive Proportional-Integral Control for Wireless Power Transfer Systems
Coupling variations caused by misalignment between the transmitters and receivers threaten the stability, reliability, and efficiency of wireless power transfer (WPT) systems. By far, various hardware and software strategies have been proposed to address the misalignment issues. Compared to the hardware-based coil design schemes, software-based adaptive control schemes are more cost-effective since only algorithms in digital controllers are changed. However, conventional adaptive control, including the adaptive proportional-integral (PI) control, may suffer from overfitting to specific operating conditions. To this end, an Artificial Intelligence (AI)-empowered design (AI-D) approach, leveraging machine learning and meta-heuristic algorithms, is proposed in this paper to enhance the robustness of adaptive PI control against coupling variations of WPT systems. Optimal design cases tailoring for diverse dynamic performances are provided, which are validated with comprehensive scenario analysis.
- 20 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 62 (1) , 1433-1443
A Robust Artificial Intelligence-Empowered Adaptive Proportional-Integral Control for Wireless Power Transfer Systems
Coupling variations caused by misalignment between the transmitters and receivers threaten the stability, reliability, and efficiency of wireless power transfer (WPT) systems. By far, various hardware and software strategies have been proposed to address the misalignment issues. Compared to the hardware-based coil design schemes, software-based adaptive control schemes are more cost-effective since only algorithms in digital controllers are changed. However, conventional adaptive control, including the adaptive proportional-integral (PI) control, may suffer from overfitting to specific operating conditions. To this end, an Artificial Intelligence (AI)-empowered design (AI-D) approach, leveraging machine learning and meta-heuristic algorithms, is proposed in this paper to enhance the robustness of adaptive PI control against coupling variations of WPT systems. Optimal design cases tailoring for diverse dynamic performances are provided, which are validated with comprehensive scenario analysis.
- 3 September 2023
- Published by Elsevier in Applied Thermal Engineering
- Vol. 236
Design of a novel Low-Temperature Polymer electrolyte Membrane fuel Cell: 3D modelling and experimental verification
- 3 September 2023
- Published by Elsevier in Applied Thermal Engineering
- Vol. 236
Design of a novel Low-Temperature Polymer electrolyte Membrane fuel Cell: 3D modelling and experimental verification