Jihong Yang

In this study, the evolution process of a landslide model under continuous rainfall conditions with a rainfall intensity of 30 mm/h is studied in depth based on an outdoor rainfall model test of a colluvial slope as the research material. The response law of pore water pressure and settlement amount is also obtained, and the influence of bedrock inclination angle on the development and deformation failure of the colluvial landslide is discussed. When the dip angle of the bedrock is 40°, it is prone to sudden slip-type landslides, and the evolution process is as follows: tensile cracks appear at the trailing edge, and these cracks continue to increase, leading to overall sliding. When the bedrock dip angle is 30°, traction landslides are prone to occur, and the evolution process is as follows: there is sliding at the foot of the slope, tensile cracks appear in the middle, sliding occurs in the middle, and tensile cracks appear in the upper part, leading to overall sliding. Before the landslide starts, the pore water pressure rises significantly. In the process of landslide evolution, the fine particles move to the foot of the slope with the rainwater, and the larger the angle of the slope, the greater the number of fine particles that accumulate at the foot of the slope, and the higher the elevation and the larger the scale of the trailing edge of the sliding body during sliding.

Shaking table tests serve as an effective method to simulate landslides triggered by seismic activities. These laboratory experiments necessitate the use of materials that mimic those encountered in real-world scenarios. For this investigation, materials analogous to field conditions for the shaking table tests were formulated using quartz sand, barite powder, iron powder, gypsum, rosin, and alcohol. Within the model test compositions, iron powder, barite powder, and quartz sand acted as aggregates; gypsum functioned as an additive, and a solution of rosin and alcohol was employed as a binder. Employing the orthogonal design method, the physical and mechanical parameters of these analogous materials were ascertained through double-sided shear tests, as well as uniaxial compression and splitting tests. Subsequent analyses included extreme difference and regression assessments targeting the determinants influencing the physical and mechanical characteristics of these materials. The ultimate goal was to determine the optimal mixing ratios for the model test materials. The findings revealed that the physical and mechanical properties of analogous materials at varying ratios span a broad spectrum, fulfilling the criteria for distinct rock model experiments. A thorough examination of the factors impacting the physical and mechanical properties of these materials was undertaken, elucidating their respective influences. Based on the relative significance of each determinant on the mechanical attributes of the analogous materials, dominant factors were identified for a multiple regression analysis, from which the regression equations corresponding to the test ratios were derived.

The creep characteristics of sliding zones strongly influence slope deformation and long-term stability, as well as the occurrence of landslide catastrophes. In this paper, large-scale triaxial creep tests were performed on the strongly weathered argillaceous sandstone sliding zone of the Huaipa landslide in the Henan Province, China, to study its creep characteristics and long-term strength in natural and saturated states. Three-dimensional numerical simulations were conducted to analyze the deformation creep law and catastrophic evolution mechanism of the slope after excavation and rainfall. The results show that the sliding zone underwent appreciable creep deformation prior to failure, and that the progression of specimen damage with an increasing stress level followed decay creep → steady creep → accelerated creep. The stress level played a decisive role in the creep deformation, with higher stress levels resulting in higher instantaneous displacement, creep displacement, and longer times required to reach steady creep. The stress level also determined the specimen’s creep stage. When the stress level was low, the adjustment of the specimen’s internal structure was dominated by air space compression and particle movement, whereas particle fragmentation mostly occurred at high stress levels. The long-term rock strength was approximately 62–66% of the instantaneous strength, the internal friction angle decreased by approximately 8° relative to the instantaneous strength, and the cohesion decreased by approximately 30%. The slope foot unloaded and deformed owing to the excavation of a bauxite mine at its front edge, after which the slope deformed via creep. The landslide disaster occurred when the deformation was significantly accelerated and the slope started to slide as a whole once the sliding zone became water saturated owing to continuous rainfall. The simulation results indicate that the landslide can be divided into a front edge bulging zone, central sliding zone, and trailing edge tension zone, which provides valuable insight on the creep deformation evolution process and the disaster mechanism of the landslide under the action of front edge excavation and rainfall.