Cheng-Huan Chen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Cheng-Huan Chen has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Po-Hung Yao
Tsinghua University
2 shared publicationsChi-Jui Chung
Department of Power Mechanical Engineering, National TsingHua University, HsinChu, 30013 Taiwan
1 shared publicationChi-Lin Wu
National Chiao Tung University
1 shared publicationChien-Li Wu
Department of Power Mechanical Engineering, National TsingHua University, HsinChu, 30013 Taiwan
1 shared publicationChiu-Ting Hsieh
National Tsing Hua University
1 shared publicationChung-Feng Chen
Department of Electronic Engineering, National Taiwan University of Science and Technology, Taipei, Taiwan
1 shared publication
Latest Publications
- 6 July 2012
- Published by Optica Publishing Group in Optics Express
- Vol. 20 (15) , 16552-16566
Low speckle laser illuminated projection system with a vibrating diffractive beam shaper
Optics InfoBase is the Optical Society's online library for flagship journals, partnered and copublished journals, and recent proceedings from OSA conferences.
- 6 July 2012
- Published by Optica Publishing Group in Optics Express
- Vol. 20 (15) , 16552-16566
Low speckle laser illuminated projection system with a vibrating diffractive beam shaper
Optics InfoBase is the Optical Society's online library for flagship journals, partnered and copublished journals, and recent proceedings from OSA conferences.
- Open Access
- 13 February 2012
- Published by Optica Publishing Group in Optics Express
- Vol. 20 (5) , 4819-4829
Polarized backlight with constrained angular divergence for enhancement of light extraction efficiency from wire grid polarizer.
Efficiency of liquid crystal displays highly depends on the amount of polarized light emerging from the backlight module. In this paper, a backlight architecture using a nanoimprint wire grid polarizer for polarization recycling is proposed and studied, in which the extraction efficiency of polarized light is the major concern. The backlight module is composed of the stack of a wire grid polarizer, a lenticular array and a light guide plate. The light guide plate features interleaving v-groove and trapezoidal ridge coated with aluminum on the top surface, and scattering dot array on the bottom. The angular divergence of emerging light from the light guide plate can be well constrained so as to exploit the angular range with the best transmission of polarized light for the wire grid polarizer. The prototype of a 2.5-inch module has demonstrated an angular divergence of 48°. The overall extraction efficiency of polarized light enhanced by 21% and uniformity of 76% have been achieved.
- 13 February 2012
- Published by Optica Publishing Group in Optics Express
- Vol. 20 (5) , 4819-4829
Open AccessPolarized backlight with constrained angular divergence for enhancement of light extraction efficiency from wire grid polarizer.
Efficiency of liquid crystal displays highly depends on the amount of polarized light emerging from the backlight module. In this paper, a backlight architecture using a nanoimprint wire grid polarizer for polarization recycling is proposed and studied, in which the extraction efficiency of polarized light is the major concern. The backlight module is composed of the stack of a wire grid polarizer, a lenticular array and a light guide plate. The light guide plate features interleaving v-groove and trapezoidal ridge coated with aluminum on the top surface, and scattering dot array on the bottom. The angular divergence of emerging light from the light guide plate can be well constrained so as to exploit the angular range with the best transmission of polarized light for the wire grid polarizer. The prototype of a 2.5-inch module has demonstrated an angular divergence of 48°. The overall extraction efficiency of polarized light enhanced by 21% and uniformity of 76% have been achieved.
- 11 June 2009
- Published by Optica Publishing Group in Applied Optics
- Vol. 48 (18) , 3446-3454
Liquid crystal panel for high efficiency barrier type autostereoscopic three-dimensional displays.
An autostereoscopic display with parallax barrier attached onto a liquid crystal panel suffers from the trade-off between brightness and crosstalk. One approach for making improvement by modifying the layout of light blocking components, such as thin film transistor, storage capacitor, and protrusion, in the liquid crystal pixel has been proposed. Ray tracing simulation shows that the aperture of the slanted barrier can be significantly increased, hence increasing efficiency, while keeping the same crosstalk level if those light blocking components can be shifted to the corner of the pixel. A six-view 2.83 in. (7.19 cm) prototype has shown improvement on both brightness and crosstalk compared to its counterpart using a traditional liquid crystal panel, which demonstrates an effective approach for a high-efficiency barrier-type autostereoscopic 3D display with a liquid crystal panel.
- 11 June 2009
- Published by Optica Publishing Group in Applied Optics
- Vol. 48 (18) , 3446-3454
Liquid crystal panel for high efficiency barrier type autostereoscopic three-dimensional displays.
An autostereoscopic display with parallax barrier attached onto a liquid crystal panel suffers from the trade-off between brightness and crosstalk. One approach for making improvement by modifying the layout of light blocking components, such as thin film transistor, storage capacitor, and protrusion, in the liquid crystal pixel has been proposed. Ray tracing simulation shows that the aperture of the slanted barrier can be significantly increased, hence increasing efficiency, while keeping the same crosstalk level if those light blocking components can be shifted to the corner of the pixel. A six-view 2.83 in. (7.19 cm) prototype has shown improvement on both brightness and crosstalk compared to its counterpart using a traditional liquid crystal panel, which demonstrates an effective approach for a high-efficiency barrier-type autostereoscopic 3D display with a liquid crystal panel.
- 20 February 2008
- Published by Optica Publishing Group in Applied Optics
- Vol. 47 (6) , 784-791
High throughput reflective light guide for planar illuminator
A light guide fully composed of reflective plate has been proposed for a planar illuminator with the light source located at the side edge. Using mirror reflection as the light guiding mechanism increases the light acceptance angle of the light guide, and the hollow structure allows increasing the source coupling area without inducing further weight. Accompanying with the optical films, for example, a diffuser, a prismatic film, and a reflective polarizer to spread light distribution, the uniformity of the prototype has shown the feasibility for a planar illuminator.
- 20 February 2008
- Published by Optica Publishing Group in Applied Optics
- Vol. 47 (6) , 784-791
High throughput reflective light guide for planar illuminator
A light guide fully composed of reflective plate has been proposed for a planar illuminator with the light source located at the side edge. Using mirror reflection as the light guiding mechanism increases the light acceptance angle of the light guide, and the hollow structure allows increasing the source coupling area without inducing further weight. Accompanying with the optical films, for example, a diffuser, a prismatic film, and a reflective polarizer to spread light distribution, the uniformity of the prototype has shown the feasibility for a planar illuminator.