Junnan Qiao
Junnan Qiao has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Gaoqiang Chen
State Key Laboratory of Clean and Efficient Turbomachinery Power Equipment, Department of Mechanical Engineering, Tsinghua University, Beijing, China
3 shared publications Chengle Yang
2 shared publicationsQingyu Shi
2 shared publicationsYang Han
2 shared publications- Baoqi Zhu1 shared publication
Boyang Zhao
1 shared publication
Latest Publications
- Open Access
- 19 August 2026
- Published by Elsevier in Next Materials
- Vol. 13
Effect of magnetic flux concentrator on the thermal behavior during induction brazing of squirrel cage rotor: A numerical simulation and experimental study
- 19 August 2026
- Published by Elsevier in Next Materials
- Vol. 13
Open AccessEffect of magnetic flux concentrator on the thermal behavior during induction brazing of squirrel cage rotor: A numerical simulation and experimental study
- 6 May 2024
- Published by Elsevier in Materials Letters
- Vol. 367
Visualization of vertical transfer of material through high-velocity rotating flow zone during friction stir welding
- 6 May 2024
- Published by Elsevier in Materials Letters
- Vol. 367
Visualization of vertical transfer of material through high-velocity rotating flow zone during friction stir welding
- Top Cited Papers
- 8 March 2024
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 272
Material flow during dissimilar friction stir welding of Al/Mg alloys
- 8 March 2024
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 272
Top Cited PapersMaterial flow during dissimilar friction stir welding of Al/Mg alloys
- Open Access
- 1 December 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (12)
Elucidation of solid-state metal flow behaviors during friction stir welding: Numerical and experimental investigation
During the process of friction stir welding, the behavior of interfacial friction holds a pivotal role in shaping both the heat generation and material flow within the workpiece. However, a quantifiable comprehension of how the friction between the tool and the workpiece (T/W) precisely influences the interface contact state and the heat generation, and the material flow remains elusive. This paper strives to address this gap by introducing a mathematical model that couples interface friction and material flow through the utilization of a shear stress boundary condition at the T/W interface, which is able to present sliding and sticking condition, in our computational fluid dynamics simulation. Notably, the simulation underscore a non-uniform distribution characterizing the friction interface contact state. It is found that augmenting the coefficient of friction (CoF) induces a transition from sliding to sticking both locally and averagely at the T/W interface. When the friction interface becomes predominantly characterized by a sticking state, the CoF exerts a nominal influence over the overall heat generation, yet maintains a discernible impact on material flow patterns. This foundation enables the elucidation of the mechanism through which the friction interface contact state impacts material flow behavior. The simulated material flow trajectory also highlight that under a sliding-dominated friction interface, materials simply flow around the tool. The material flow trajectories on the advancing side (AS) and the retreating side (RS) are approximately symmetrical. The materials driven by the shoulder and the pin are converged at the center of the weld behind the tool. Simulation and experimental results demonstrate that under a sticking-dominated friction interface, materials tend to undertake multiple circulations around the tool and migrate downward to the AS. Other materials are observed to migrate upward to the RS. The entrance point for this circular behavior resides in the AS situated beneath the shoulder.
- 1 December 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (12)
Open AccessElucidation of solid-state metal flow behaviors during friction stir welding: Numerical and experimental investigation
During the process of friction stir welding, the behavior of interfacial friction holds a pivotal role in shaping both the heat generation and material flow within the workpiece. However, a quantifiable comprehension of how the friction between the tool and the workpiece (T/W) precisely influences the interface contact state and the heat generation, and the material flow remains elusive. This paper strives to address this gap by introducing a mathematical model that couples interface friction and material flow through the utilization of a shear stress boundary condition at the T/W interface, which is able to present sliding and sticking condition, in our computational fluid dynamics simulation. Notably, the simulation underscore a non-uniform distribution characterizing the friction interface contact state. It is found that augmenting the coefficient of friction (CoF) induces a transition from sliding to sticking both locally and averagely at the T/W interface. When the friction interface becomes predominantly characterized by a sticking state, the CoF exerts a nominal influence over the overall heat generation, yet maintains a discernible impact on material flow patterns. This foundation enables the elucidation of the mechanism through which the friction interface contact state impacts material flow behavior. The simulated material flow trajectory also highlight that under a sliding-dominated friction interface, materials simply flow around the tool. The material flow trajectories on the advancing side (AS) and the retreating side (RS) are approximately symmetrical. The materials driven by the shoulder and the pin are converged at the center of the weld behind the tool. Simulation and experimental results demonstrate that under a sticking-dominated friction interface, materials tend to undertake multiple circulations around the tool and migrate downward to the AS. Other materials are observed to migrate upward to the RS. The entrance point for this circular behavior resides in the AS situated beneath the shoulder.