Yifan Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yifan Liu has a total of 68 co-authors. Here are the top co-authors by number of shared publications:
- Franklyn Quinlan
Time and Frequency Division, National Institute of Standards and Technology, Boulder, CO 80305, USA
12 shared publications - Charles A. McLemore
National Institute of Standards and Technology
7 shared publications - Takuma Nakamura
National Institute of Standards and Technology
7 shared publications Peter Rakich
Department of Applied Physics, Yale University 3 , New Haven, Connecticut 06520
6 shared publications- Scott A. Diddams
University of Colorado
6 shared publications - Dahyeon Lee
JILA
5 shared publications
Latest Publications
- 20 April 2026
- Published by Optica Publishing Group in Optics Letters
- Vol. 51 (9) , 2488-2491
Fiber link stabilization with a multicore fiber amplifier
We study the use of separate cores of a multicore erbium-doped fiber amplifier (MC-EDFA) in a noise-canceled link for ultrastable optical frequency transfer. We demonstrate fractional frequency instability of 5×10 −19 at 1000 s averaging time for the stabilized MC-EDFA alone and 1.4×10 −18 at 1000 s averaging time when integrated with a 40-km-long 7-core spooled fiber. This study further establishes multicore fiber (MCF) networks as a promising platform for ultrastable frequency transfer, serving as an important step toward incorporating precision time and frequency distribution into future MCF communication infrastructures.
- 20 April 2026
- Published by Optica Publishing Group in Optics Letters
- Vol. 51 (9) , 2488-2491
Fiber link stabilization with a multicore fiber amplifier
We study the use of separate cores of a multicore erbium-doped fiber amplifier (MC-EDFA) in a noise-canceled link for ultrastable optical frequency transfer. We demonstrate fractional frequency instability of 5×10 −19 at 1000 s averaging time for the stabilized MC-EDFA alone and 1.4×10 −18 at 1000 s averaging time when integrated with a 40-km-long 7-core spooled fiber. This study further establishes multicore fiber (MCF) networks as a promising platform for ultrastable frequency transfer, serving as an important step toward incorporating precision time and frequency distribution into future MCF communication infrastructures.
- Open Access
- 1 December 2025
- Published by AIP Publishing in APL Photonics
- Vol. 10 (12)
From ultra-noisy to ultra-stable: Optimization of the optoelectronic laser lock
We demonstrate the direct locking of a 820 kHz linewidth semiconductor distributed feedback laser to a high finesse, compact, and ultrastable reference cavity using the optoelectronic (OEO) laser locking method, resulting in cavity thermal noise-limited phase noise performance. We compare the OEO lock to the standard Pound–Drever–Hall method, demonstrating several new aspects and advantages of the OEO lock in attaining low phase noise from noisy lasers, including reducing the residual laser noise by more than 140 dB compared to its free-running level at a 10 Hz offset. In addition, we introduce a new RF feedforward noise-correction scheme that transfers the stability of the ultrastable reference cavity to an optical frequency comb even if the cavity-stabilized laser itself has high residual noise. We also reveal an OEO lock state that is capable of extremely high levels of laser noise rejection using feedforward, exceeding current theoretical models by ∼15 dB. By combining compact laser sources with sub-1 ml volume and ultrastable optical cavities, this work enables extremely compact and robust ultrastable laser systems with applications in low phase noise microwave generation, sensing, and satellite ranging.
- 1 December 2025
- Published by AIP Publishing in APL Photonics
- Vol. 10 (12)
Open AccessFrom ultra-noisy to ultra-stable: Optimization of the optoelectronic laser lock
We demonstrate the direct locking of a 820 kHz linewidth semiconductor distributed feedback laser to a high finesse, compact, and ultrastable reference cavity using the optoelectronic (OEO) laser locking method, resulting in cavity thermal noise-limited phase noise performance. We compare the OEO lock to the standard Pound–Drever–Hall method, demonstrating several new aspects and advantages of the OEO lock in attaining low phase noise from noisy lasers, including reducing the residual laser noise by more than 140 dB compared to its free-running level at a 10 Hz offset. In addition, we introduce a new RF feedforward noise-correction scheme that transfers the stability of the ultrastable reference cavity to an optical frequency comb even if the cavity-stabilized laser itself has high residual noise. We also reveal an OEO lock state that is capable of extremely high levels of laser noise rejection using feedforward, exceeding current theoretical models by ∼15 dB. By combining compact laser sources with sub-1 ml volume and ultrastable optical cavities, this work enables extremely compact and robust ultrastable laser systems with applications in low phase noise microwave generation, sensing, and satellite ranging.
- Open Access
- 1 September 2025
- Published by AIP Publishing in APL Photonics
- Vol. 10 (9)
Dual laser self-injection locking to a micro Fabry–Perot for low phase noise millimeter-wave generation
Low-noise and accessible millimeter-wave sources are critical for emergent telecommunications, radar, and sensing applications. Current limitations to realizing low-noise, deployable millimeter-wave systems include size, weight, and power requirements, along with complex operating principles. In this paper, we provide a compact photonic implementation for generating low phase noise millimeter-waves, which significantly simplifies the architecture and reduces the volume compared to alternative approaches. Two commercial diode lasers are self-injection-locked to a micro-Fabry–Perot cavity, and their heterodyne provides low phase noise millimeter-waves reaching −148 dBc/Hz at 1 MHz offset on a 111.45 GHz carrier. Phase noise characterization at such levels and frequencies poses unique challenges, and we further highlight the capabilities of optically based measurement techniques. Our approach to millimeter-wave generation can leverage advances in photonic integration for further miniaturization and packaging, thus providing a unique source of accessible, compact, and low-noise millimeter-waves.
- 1 September 2025
- Published by AIP Publishing in APL Photonics
- Vol. 10 (9)
Open AccessDual laser self-injection locking to a micro Fabry–Perot for low phase noise millimeter-wave generation
Low-noise and accessible millimeter-wave sources are critical for emergent telecommunications, radar, and sensing applications. Current limitations to realizing low-noise, deployable millimeter-wave systems include size, weight, and power requirements, along with complex operating principles. In this paper, we provide a compact photonic implementation for generating low phase noise millimeter-waves, which significantly simplifies the architecture and reduces the volume compared to alternative approaches. Two commercial diode lasers are self-injection-locked to a micro-Fabry–Perot cavity, and their heterodyne provides low phase noise millimeter-waves reaching −148 dBc/Hz at 1 MHz offset on a 111.45 GHz carrier. Phase noise characterization at such levels and frequencies poses unique challenges, and we further highlight the capabilities of optically based measurement techniques. Our approach to millimeter-wave generation can leverage advances in photonic integration for further miniaturization and packaging, thus providing a unique source of accessible, compact, and low-noise millimeter-waves.
- 19 June 2025
- Published by Optica Publishing Group in Optica
- Vol. 12 (6) , 894
Ultrastable optical frequency transfer and attosecond timing in deployed multicore fiber
The telecommunications industry’s deployment of billions of kilometers of optical fiber has created a vast global network that can be exploited for additional applications such as environmental sensing, quantum networking, and international clock comparisons. However, for reasons such as the unidirectionality of long-haul fiber links, telecom fiber networks cannot always be adapted for important applications beyond data transmission. Fortunately, new multicore optical fibers create the opportunity for application coexistence with data traffic, creating multifunctional networks. Toward that end, we propose and demonstrate the faithful transfer of ultrastable optical signals through deployed multicore fiber in a way that is compatible with the unidirectionality of long-haul fiber optic systems, demonstrating fractional frequency instability of 3×10−19 at 10,000 s. By supporting state-of-the-art optical atomic clocks, subsea multicore fibers can break the distance barrier for ultrastable optical frequency transfer, opening the door to intercontinental optical clock comparisons at the highest level, with applications in fundamental physics, relativistic geodesy, and the redefinition of the second.
- 19 June 2025
- Published by Optica Publishing Group in Optica
- Vol. 12 (6) , 894
Ultrastable optical frequency transfer and attosecond timing in deployed multicore fiber
The telecommunications industry’s deployment of billions of kilometers of optical fiber has created a vast global network that can be exploited for additional applications such as environmental sensing, quantum networking, and international clock comparisons. However, for reasons such as the unidirectionality of long-haul fiber links, telecom fiber networks cannot always be adapted for important applications beyond data transmission. Fortunately, new multicore optical fibers create the opportunity for application coexistence with data traffic, creating multifunctional networks. Toward that end, we propose and demonstrate the faithful transfer of ultrastable optical signals through deployed multicore fiber in a way that is compatible with the unidirectionality of long-haul fiber optic systems, demonstrating fractional frequency instability of 3×10−19 at 10,000 s. By supporting state-of-the-art optical atomic clocks, subsea multicore fibers can break the distance barrier for ultrastable optical frequency transfer, opening the door to intercontinental optical clock comparisons at the highest level, with applications in fundamental physics, relativistic geodesy, and the redefinition of the second.
- Top Cited PapersOpen Access
- 6 June 2025
- Published by Springer Nature in Nature Photonics
- Vol. 19 (9) , 992-998
Harnessing micro-Fabry–Pérot reference cavities in photonic integrated circuits
- 6 June 2025
- Published by Springer Nature in Nature Photonics
- Vol. 19 (9) , 992-998
Top Cited PapersOpen AccessHarnessing micro-Fabry–Pérot reference cavities in photonic integrated circuits
- 1 January 2025
- Published by Optica Publishing Group
- p. W2A.27
Temperature Effect on the Correlation Between Cores in a 7-Core Fiber
We investigate the change in phase correlations between individual cores of a 40 km-long 7-core optical fiber under continuously varying temperatures, showing that relative path length changes among most cores are less than 10-8/°C.
- 1 January 2025
- Published by Optica Publishing Group
- p. W2A.27
Temperature Effect on the Correlation Between Cores in a 7-Core Fiber
We investigate the change in phase correlations between individual cores of a 40 km-long 7-core optical fiber under continuously varying temperatures, showing that relative path length changes among most cores are less than 10-8/°C.
- 14 November 2024
- Published by Optica Publishing Group in Optica
- Vol. 11 (11) , 1583-1587
Photonic millimeter-wave generation beyond the cavity thermal limit
Next-generation communications, radar, and navigation systems will extend and exploit the higher bandwidth of the millimeter-wave domain for increased communication data rates as well as radar with higher sensitivity and increased spatial resolution. However, realizing these advantages will require the generation of millimeter-wave signals with low phase noise in simple and compact form-factors. Photonic integration addresses this challenge and provides a path toward simplified and portable, low-noise mm-wave generation. We leverage these advances by heterodyning two silicon photonic chip lasers, phase-locked to different axial modes of a miniature Fabry–Perot (F-P) cavity to demonstrate a simple framework for generating low-noise millimeter-waves. By reducing technical noise, we achieve common-mode rejection of the thermally driven Brownian noise such that the millimeter-wave phase noise surpasses that of the thermal limit of a single laser locked to the F-P cavity. This leads to a 118.1 GHz millimeter-wave signal with phase noise of −118dBc/Hz at 10 kHz offset, decreasing to −120dBc/Hz at 30 kHz offset. We achieve this with technologies that can be integrated into a platform less than ≈10mL. Our work overcomes fundamental thermal-mechanical noise limits intrinsic to integrated photonics, while illustrating advantages of the same for providing low-size, -weight, and -power (SWaP) mm-waves that will be enabling for multiple applications in communications and sensing.
- 14 November 2024
- Published by Optica Publishing Group in Optica
- Vol. 11 (11) , 1583-1587
Photonic millimeter-wave generation beyond the cavity thermal limit
Next-generation communications, radar, and navigation systems will extend and exploit the higher bandwidth of the millimeter-wave domain for increased communication data rates as well as radar with higher sensitivity and increased spatial resolution. However, realizing these advantages will require the generation of millimeter-wave signals with low phase noise in simple and compact form-factors. Photonic integration addresses this challenge and provides a path toward simplified and portable, low-noise mm-wave generation. We leverage these advances by heterodyning two silicon photonic chip lasers, phase-locked to different axial modes of a miniature Fabry–Perot (F-P) cavity to demonstrate a simple framework for generating low-noise millimeter-waves. By reducing technical noise, we achieve common-mode rejection of the thermally driven Brownian noise such that the millimeter-wave phase noise surpasses that of the thermal limit of a single laser locked to the F-P cavity. This leads to a 118.1 GHz millimeter-wave signal with phase noise of −118dBc/Hz at 10 kHz offset, decreasing to −120dBc/Hz at 30 kHz offset. We achieve this with technologies that can be integrated into a platform less than ≈10mL. Our work overcomes fundamental thermal-mechanical noise limits intrinsic to integrated photonics, while illustrating advantages of the same for providing low-size, -weight, and -power (SWaP) mm-waves that will be enabling for multiple applications in communications and sensing.
- 21 August 2024
- Published by Optica Publishing Group in Optica
- Vol. 11 (9) , 1205-1211
Ultrastable vacuum-gap Fabry–Perot cavities operated in air
We demonstrate a vacuum-gap ultrastable optical reference cavity that does not require a vacuum enclosure. Our simple method of optical contact bonding in a vacuum environment allows for cavity operation in air while maintaining vacuum between the cavity mirrors. Vacuum is maintained long term, with no observed degradation in cavity stability for over 1 year after bonding. For a 1550 nm laser stabilized to a 9.7 mL in-vacuum bonded cavity, the measured Allan deviation is 2.4×10−14 at 1 s, and its phase noise is thermal-noise-limited from 0.1 Hz to 10 kHz, reaching about −105dBc/Hz at 10 kHz offset frequency. This represents the highest stability of any oscillator operated without a vacuum enclosure, to our knowledge. Furthermore, we demonstrate a 0.5 mL in-vacuum bonded cavity created using microfabricated mirrors and cavity dicing, with phase noise reaching −95 dBc/Hz at 10 kHz offset frequency. By relieving the need for high-vacuum enclosures, we greatly enhance the portability and utility of low-noise, compact, cavity-stabilized lasers, with applications ranging from environmental sensing to mobile optical clocks to ultralow-noise microwave generation.
- 21 August 2024
- Published by Optica Publishing Group in Optica
- Vol. 11 (9) , 1205-1211
Ultrastable vacuum-gap Fabry–Perot cavities operated in air
We demonstrate a vacuum-gap ultrastable optical reference cavity that does not require a vacuum enclosure. Our simple method of optical contact bonding in a vacuum environment allows for cavity operation in air while maintaining vacuum between the cavity mirrors. Vacuum is maintained long term, with no observed degradation in cavity stability for over 1 year after bonding. For a 1550 nm laser stabilized to a 9.7 mL in-vacuum bonded cavity, the measured Allan deviation is 2.4×10−14 at 1 s, and its phase noise is thermal-noise-limited from 0.1 Hz to 10 kHz, reaching about −105dBc/Hz at 10 kHz offset frequency. This represents the highest stability of any oscillator operated without a vacuum enclosure, to our knowledge. Furthermore, we demonstrate a 0.5 mL in-vacuum bonded cavity created using microfabricated mirrors and cavity dicing, with phase noise reaching −95 dBc/Hz at 10 kHz offset frequency. By relieving the need for high-vacuum enclosures, we greatly enhance the portability and utility of low-noise, compact, cavity-stabilized lasers, with applications ranging from environmental sensing to mobile optical clocks to ultralow-noise microwave generation.
- Top Cited PapersOpen Access
- 6 March 2024
- Published by Springer Nature in Nature
- Vol. 627 (8004) , 534-539
Photonic chip-based low-noise microwave oscillator
Numerous modern technologies are reliant on the low-phase noise and exquisite timing stability of microwave signals. Substantial progress has been made in the field of microwave photonics, whereby low-noise microwave signals are generated by the down-conversion of ultrastable optical references using a frequency comb1–3. Such systems, however, are constructed with bulk or fibre optics and are difficult to further reduce in size and power consumption. In this work we address this challenge by leveraging advances in integrated photonics to demonstrate low-noise microwave generation via two-point optical frequency division4,5. Narrow-linewidth self-injection-locked integrated lasers6,7 are stabilized to a miniature Fabry–Pérot cavity8, and the frequency gap between the lasers is divided with an efficient dark soliton frequency comb9. The stabilized output of the microcomb is photodetected to produce a microwave signal at 20 GHz with phase noise of −96 dBc Hz−1 at 100 Hz offset frequency that decreases to −135 dBc Hz−1 at 10 kHz offset—values that are unprecedented for an integrated photonic system. All photonic components can be heterogeneously integrated on a single chip, providing a significant advance for the application of photonics to high-precision navigation, communication and timing systems.
- 6 March 2024
- Published by Springer Nature in Nature
- Vol. 627 (8004) , 534-539
Top Cited PapersOpen AccessPhotonic chip-based low-noise microwave oscillator
Numerous modern technologies are reliant on the low-phase noise and exquisite timing stability of microwave signals. Substantial progress has been made in the field of microwave photonics, whereby low-noise microwave signals are generated by the down-conversion of ultrastable optical references using a frequency comb1–3. Such systems, however, are constructed with bulk or fibre optics and are difficult to further reduce in size and power consumption. In this work we address this challenge by leveraging advances in integrated photonics to demonstrate low-noise microwave generation via two-point optical frequency division4,5. Narrow-linewidth self-injection-locked integrated lasers6,7 are stabilized to a miniature Fabry–Pérot cavity8, and the frequency gap between the lasers is divided with an efficient dark soliton frequency comb9. The stabilized output of the microcomb is photodetected to produce a microwave signal at 20 GHz with phase noise of −96 dBc Hz−1 at 100 Hz offset frequency that decreases to −135 dBc Hz−1 at 10 kHz offset—values that are unprecedented for an integrated photonic system. All photonic components can be heterogeneously integrated on a single chip, providing a significant advance for the application of photonics to high-precision navigation, communication and timing systems.
- Open Access
- 1 January 2024
- Published by AIP Publishing in APL Photonics
- Vol. 9 (1)
Low-noise microwave generation with an air-gap optical reference cavity
We demonstrate a high finesse, microfabricated mirror-based, air-gap cavity with volume less than 1 ml, constructed in an array, that can support low-noise microwave generation through optical frequency division. We use the air-gap cavity in conjunction with a 10 nm bandwidth mode-locked laser to generate low phase noise 10 GHz microwaves, exhibiting a phase noise of −95 and −142 dBc/Hz at 100 Hz and 10 kHz offset frequencies, respectively. This is accomplished using the 2-point lock optical frequency division method, where we exploit 40 dB common-mode rejection of two lasers separated by 1.29 THz and locked to the same air-gap cavity. If used with an octave spanning comb, the air-gap cavity is capable of supporting 10 GHz phase noise below −160 dBc/Hz at 10 kHz offset, a level significantly lower than electronic synthesizers. These results show how extremely small optical reference cavities, operated without the benefit of vacuum enclosures or thermal insulation, can, nonetheless, support state-of-the-art microwave phase noise in compact and portable systems.
- 1 January 2024
- Published by AIP Publishing in APL Photonics
- Vol. 9 (1)
Open AccessLow-noise microwave generation with an air-gap optical reference cavity
We demonstrate a high finesse, microfabricated mirror-based, air-gap cavity with volume less than 1 ml, constructed in an array, that can support low-noise microwave generation through optical frequency division. We use the air-gap cavity in conjunction with a 10 nm bandwidth mode-locked laser to generate low phase noise 10 GHz microwaves, exhibiting a phase noise of −95 and −142 dBc/Hz at 100 Hz and 10 kHz offset frequencies, respectively. This is accomplished using the 2-point lock optical frequency division method, where we exploit 40 dB common-mode rejection of two lasers separated by 1.29 THz and locked to the same air-gap cavity. If used with an octave spanning comb, the air-gap cavity is capable of supporting 10 GHz phase noise below −160 dBc/Hz at 10 kHz offset, a level significantly lower than electronic synthesizers. These results show how extremely small optical reference cavities, operated without the benefit of vacuum enclosures or thermal insulation, can, nonetheless, support state-of-the-art microwave phase noise in compact and portable systems.