Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Alessandro Cardarelli has a total of 36 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Solvent Selection in Organosolv Fractionation of Cardoon Waste Biomass: Balancing Material Properties and Environmental Performance

    by Orawan Chailee, Giacomo Fabbrizi, Alessandro Cardarelli, Andrea Nicolini, Marco Barbanera, Ilaria Armentano

    Cardoon stalks were fractionated through three solvent-specific organosolv processes based on γ-valerolactone (GVL)/water, acetone/water and ethanol (EtOH)/water. The recovered cellulose-rich pulps and organosolv lignins were evaluated in terms of composition, morphology, functional groups and thermal behavior, and the environmental performance of the three processes was assessed through a prospective cradle-to-gate life cycle assessment. EtOH/water produced the pulp with the highest cellulose concentration (88.4%) and cellulose recovery (84.1%), whereas GVL/water achieved the highest lignin removal (89.4%) and recovered the largest amount of lignin. The pulps showed solvent-dependent surface morphologies and thermal stability, although their thermal degradation temperatures were similar. Environmental impacts were evaluated using two functional units: 1 kg of cellulose equivalent contained in the dry pulp and 1 kg of recovered dry lignin. Under the cellulose-oriented perspective, acetone/water showed the lowest global warming impact (3.73 kg CO₂ eq), followed by EtOH/water (4.19 kg CO₂ eq) and GVL/water (4.95 kg CO₂ eq). When recovered lignin was used as the reference product, GVL/water became the most favorable process for most energy- and resource-related indicators because of its higher lignin output. Sensitivity analysis confirmed that the comparative ranking was generally robust to variations in direct heat demand and substitution effectiveness, whereas reduced solvent recovery caused substantial multicategory burden shifting and altered the cellulose-oriented climate ranking. Overall, solvent selection involves trade-offs among fractionation efficiency, product properties, and environmental performance and should therefore be guided by the intended target product and the achievable solvent-recovery efficiency.

  • Open Access

    Preliminary Assessment of BNC Membranes as Solvent Delivery Systems for the Cleaning of Mural Paintings: Comparison with Traditional Gel Systems

    by Francesco Menconi, Ulderico Santamaria, Alessandro Cardarelli, Eleonora Imperio, Sara Iafrate

    Growing demand for greener and more sustainable materials in cultural heritage conservation has prompted the investigation of bio-based alternatives for cleaning applications. This study presents a preliminary evaluation of bacterial nanocellulose (BNC) membranes for the removal of acrylic resins from mural paintings, comparing commercial medical-grade and laboratory-produced BNC with conventional gel systems under simulated application conditions. Both BNC types were characterized in terms of composition, pH, electrical conductivity, Water Holding Capacity and Water Retention Rate. Acetone loading via solvent exchange was assessed by thermogravimetric analysis (TGA), while mechanical behavior before and after solvent loading was evaluated through tensile testing and optical density measurements of the immersion media. The performance of BNCs and reference delivery systems was comparatively assessed in terms of solvent retention, solvent penetration depth into the substrate and residue release. Cleaning performance was investigated through FTIR spectroscopy and semi-quantitative image analysis as indirect indicators of residual resin content, on both mock-up samples and in situ applications. Under the tested conditions, both BNC membranes were compatible with acetone loading and maintained mechanical integrity after solvent exposure. FTIR analysis showed a reduction in the acrylic carbonyl band after treatment with acetone-loaded BNC, which exhibited greater solvent diffusion depth; the underlying removal mechanism, including the possible contribution of solvent-driven redistribution phenomena, remains to be clarified. Differences in reproducibility were observed between medical-grade and laboratory-produced BNC. Overall, the study provides experimental data contributing to the assessment of BNC membranes as bio-based solvent delivery systems for conservation practice.

  • Open Access

    Chestnut Wood Residues, with and Without Tannins, as a Potential Feedstock for PHA Bioplastic Production

    by Jasmina Jusic, Alessandra Filieri, Silvia Crognale, Matteo Manni, Swati Tamantini, Vittorio Vinciguerra, Alessandro Cardarelli, Marco Barbanera, Dennis Jones, Dominik Matt, et al.

    The valorisation of lignocellulosic residues into bio-based feedstocks is a key strategy for advancing circular bioeconomy models. In this study, chestnut wood residues, including virgin wood (VW) and detannized wood (DT) from the tannin industry, were evaluated as substrates for polyhydroxyalkanoate (PHA) production using Cupriavidus necator. Biomass was subjected to thermo-acid hydrolysis followed by ion-exchange detoxification, yielding hydrolysates rich in organic acids (levulinic, acetic, and formic acids) and residual inhibitory compounds. Both substrates supported microbial growth and PHA accumulation, although clear differences in performance were observed. The maximum biomass concentration reached 1.26 ± 0.01 g L−1 in VW hydrolysate and 0.40 ± 0.03 g L−1 in DT hydrolysate. PHA production was higher in VW hydrolysate, reaching 68.51 mg L−1 with 5.44% (w/w) accumulation, while DT hydrolysate yielded 0.21 mg L−1 with 6.01% (w/w). The reduced biomass formation in DT hydrolysate was associated with the greater persistence of inhibitory compounds generated during thermo-acid treatment. Although the obtained PHA yields are lower than those reported for optimized lignocellulosic systems, this study demonstrates for the first time the feasibility of producing PHA from chestnut wood residues, including industrial detannized byproducts, without nutrient supplementation. These findings highlight the potential of tannin-industry waste streams as alternative feedstocks for biopolymer production, while indicating that optimization of hydrolysis conditions, detoxification efficiency, and fermentation strategy is required to improve process performance.


  • Open Access

    Consequential life cycle assessment of activated hydrochar-enhanced cement plaster from municipal waste

    by Alessandro Cardarelli, Claudia Fabiani, Emanuele Fanelli, Lorena Foschi, Anna Laura Pisello, Marco Barbanera


  • Open Access

    Kinetic analysis and prediction modeling by advanced machine learning of pyrolysis of dairy cattle manure from conventional and organic systems

    by Alessandro Cardarelli, Michele Ciambella, Pietro Fornai, Marco Marconi, Diego Pennino, Luca Tortora, Marco Barbanera


  • Open Access

    Kinetic and thermodynamic behavior of co-pyrolysis of olive pomace and thermoplastic waste via thermogravimetric analysis

    by N. Sánchez-Ávila, Alessandro Cardarelli, Miguel Carmona-Cabello, M.P. Dorado, Sara Pinzi, Marco Barbanera


  • Open Access

    Investigation of Hydrothermal Carbonization of Exhausted Chestnut from Tannin Extraction: Impact of Process Water Recirculation for Sustainable Fuel Production

    by Alessandro Cardarelli, Cristian Cordelli, Manuela Romagnoli, Francesco Pizzo, Marco Barbanera

    This study explores the hydrothermal carbonization (HTC) process applied to the exhausted chestnut produced by the tannin extraction industry, utilizing process water recirculation to enhance the efficiency and sustainability of the conversion process. Tannin extraction from wood typically involves hot water treatment, leaving behind residual wood biomass known as exhausted wood. These by-products maintain their renewable properties because they have only been exposed to hot water under a high pressure, which is unlikely to cause major alterations in their structural components. Hydrothermal treatment was carried out at temperatures of 220 °C and 270 °C for 1 h, with process water being recirculated four times. This investigation focused on analyzing the effects of recirculation on the yield and fuel properties of hydrochar, as well as characterizing the combustion behavior of the obtained hydrochar. The results indicated that recirculation of process water led to improvements in both the mass and energy yields of hydrochar. The mass yield of the hydrochar samples increased by 5–6%, and the ERE of the hydrochar samples increased by 5–8% compared to the HTC reference sample. However, alterations in the combustion characteristics were observed, including decreases in ignition temperature and combustion reactivity. The results indicate that, with PW recirculations, the combustion index decreased by about 14% and 18% for 220 °C and 270 °C, respectively. Overall, this research demonstrates the potential of utilizing HTC on chestnut tannin residue with process water recirculation to produce stable solid fuel and provides insights into the combustion behavior of the resulting hydrochar.


  • Open Access

    Substitution of Fossil Coal with Hydrochar from Agricultural Waste in the Electric Arc Furnace Steel Industry: A Comprehensive Life Cycle Analysis

    by Alessandro Cardarelli, Marco Barbanera

    The iron and steel industry remains one of the most energy-intensive activities with high CO2 emissions. Generally, the use of fossil coal as chemical energy in an electric arc furnace (EAF) makes up 40–70% of the total direct emissions in this steelmaking process. Therefore, substituting conventional fossil fuels with alternatives is an attractive option for reducing CO2 emissions. In this study, the environmental impacts of EAF-produced steel were comprehensively assessed using pulverized hydrochar as the charged and injected material as a replacement for fossil coal. An environmental analysis was performed based on the LCA methodology according to the framework of ISO 14044. This study evaluated two different outlines: the use of fossil coal and its replacement with hydrochar from the winemaking industry as a carbon source in the EAF steelmaking process. The environmental impacts from the manufacturing of the hydrochar were calculated using different scenarios, including novel industrial ways to use vinasse as a moisture source for the co-hydrothermal carbonization of vine pruning and exhausted grape marc (EGM). The environmental impacts per unit of steel were reported as a function of the ratio between the fixed carbon of the injected material and the material amount itself. The results highlight the sustainability of the hydrothermal carbonization process and the use of the hydrochar in EAF steelmaking. Moreover, the electricity mix used for the EAF process has significant relevance. The main outline of the results might assist decision-makers to determine which technological route is most likely to be effective in reducing future CO2 emissions from the iron and steel industry.


  • Open Access

    Preliminary environmental and economic assessment of polyurethane foam produced by microwave-assisted liquefaction of riparian shrubs

    by Alessandro Cardarelli, Franco Cotana, Ilaria Baffo, Gianluca Cavalaglio, Marco Barbanera

    The study aims to develop a full-scale plant to produce biobased PU foam from microwave liquefaction of riparian shrubs and to evaluate its environmental burden using a cradle-to-gate, scaled-up LCA approach. Life Cycle Inventory was built on experimental data for polyol synthesis by using Response Surface Methodology (RSM) to maximize the liquefaction yield. Bio-based PU foam was also compared with the petrochemical counterpart. Life Cycle Assessment was carried out using SimaPro 9.0 software and impacts were evaluated with EPD 2007 method. The results indicate that the methylene diphenyl diisocyanate production and the energy consumption for the liquefaction step are the major sources of impacts. Overall, the environmental superiority of biobased polyurethane cannot always be claimed with respect to their fossil counterpart. Finally, a simplified economic assessment showed that for the bio-based PU foam an interesting profitability could be obtained for a market price of 4.5 €/kg.