Samuel Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Samuel Yang has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Zetian Mi
Department of Electrical Engineering and Computer Science University of Michigan Ann Arbor Michigan USA
13 shared publications - Jiangnan Liu
University of Michigan
9 shared publications - Shubham Mondal
Department of Electrical Engineering and Computer Science, University of Michigan 1 , Ann Arbor, Michigan 48109
8 shared publications - Danhao Wang
Department of Electrical Engineering and Computer Science, University of Michigan, Ann Arbor, USA
7 shared publications - Ding Wang
State Key Laboratory for Mesoscopic Physics and Frontiers Science Center for Nano-optoelectronics, School of Physics, Peking University 1 , Beijing 100871
7 shared publications - Mehedi Hasan Tanim
Department of Electrical Engineering and Computer Science, University of Michigan 1 , Ann Arbor, Michigan 48109
5 shared publications
Latest Publications
- 10 August 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (6)
Molecular beam epitaxy and characterization of wurtzite LaAlN
We report the molecular beam epitaxy and structural characterization of single-phase wurtzite LaxAl1−xN thin films, with a La composition as high as x=0.20. In situ reflection high-energy electron diffraction confirms epitaxial film formation, and atomic force microscopy reveals sub-nanometer surface roughness for all compositions investigated. High-resolution x-ray diffraction and scanning transmission electron microscopy further confirm c-axis orientation, high crystalline quality, and precise in-plane epitaxial alignment. Importantly, atomic-resolution structural analysis demonstrates a continuous decrease in the c/a lattice-parameter ratio with increasing La content. In addition, out-of-plane piezoresponse force microscopy measurements show an enhanced effective d33, increasing from 5.00 pm/V for AlN to 7.66 pm/V for La0.20Al0.80N. These results establish LaAlN as a promising new wurtzite nitride alloy platform for future wide bandgap electronics, optoelectronics, and quantum photonics.
- 10 August 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (6)
Molecular beam epitaxy and characterization of wurtzite LaAlN
We report the molecular beam epitaxy and structural characterization of single-phase wurtzite LaxAl1−xN thin films, with a La composition as high as x=0.20. In situ reflection high-energy electron diffraction confirms epitaxial film formation, and atomic force microscopy reveals sub-nanometer surface roughness for all compositions investigated. High-resolution x-ray diffraction and scanning transmission electron microscopy further confirm c-axis orientation, high crystalline quality, and precise in-plane epitaxial alignment. Importantly, atomic-resolution structural analysis demonstrates a continuous decrease in the c/a lattice-parameter ratio with increasing La content. In addition, out-of-plane piezoresponse force microscopy measurements show an enhanced effective d33, increasing from 5.00 pm/V for AlN to 7.66 pm/V for La0.20Al0.80N. These results establish LaAlN as a promising new wurtzite nitride alloy platform for future wide bandgap electronics, optoelectronics, and quantum photonics.
- 3 August 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (5)
Ferroelectric nitrogen-polar ScAlN heterostructures on 4H-SiC enabled by thin AlN buffer layers
The expansive functional landscape of ferroelectric nitrides has sharpened interest in host platforms that can preserve excellent structural quality while extending operation to high-temperature, harsh-environment regimes. 4H-SiC is especially compelling owing to its thermal robustness, high thermal conductivity, and close lattice correspondence with AlN. Here, we report robust ferroelectric ScAlN-on-4H-SiC heterostructures enabled by thin, exceptionally high-quality AlN templating, grown via plasma-assisted molecular beam epitaxy. A 40 nm nitrogen-polar AlN buffer layer on carbon-terminated 4H-SiC yields highly ordered and dense films, providing an abrupt, structurally coherent, true wurtzite interface for ScAlN heteroepitaxy. Across a broad Sc composition range, a single dominant epitaxial orientation and monocrystalline wurtzite character are maintained without detectable secondary phases. Electrical measurements reveal room-temperature ferroelectricity in as-grown films with coercive fields and remanent polarizations comparable to ScAlN films grown directly on conductive substrates. Taken altogether, these findings establish AlN templating on 4H-SiC as a practical route to structurally controllable and reproducible all-epitaxial ferroelectric nitride heterostructures for extreme-environment electronic, acoustic, and memory applications.
- 3 August 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (5)
Ferroelectric nitrogen-polar ScAlN heterostructures on 4H-SiC enabled by thin AlN buffer layers
The expansive functional landscape of ferroelectric nitrides has sharpened interest in host platforms that can preserve excellent structural quality while extending operation to high-temperature, harsh-environment regimes. 4H-SiC is especially compelling owing to its thermal robustness, high thermal conductivity, and close lattice correspondence with AlN. Here, we report robust ferroelectric ScAlN-on-4H-SiC heterostructures enabled by thin, exceptionally high-quality AlN templating, grown via plasma-assisted molecular beam epitaxy. A 40 nm nitrogen-polar AlN buffer layer on carbon-terminated 4H-SiC yields highly ordered and dense films, providing an abrupt, structurally coherent, true wurtzite interface for ScAlN heteroepitaxy. Across a broad Sc composition range, a single dominant epitaxial orientation and monocrystalline wurtzite character are maintained without detectable secondary phases. Electrical measurements reveal room-temperature ferroelectricity in as-grown films with coercive fields and remanent polarizations comparable to ScAlN films grown directly on conductive substrates. Taken altogether, these findings establish AlN templating on 4H-SiC as a practical route to structurally controllable and reproducible all-epitaxial ferroelectric nitride heterostructures for extreme-environment electronic, acoustic, and memory applications.
- 27 July 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (4)
Composition-dependent ferroelectricity in epitaxial AlYN
We report molecular beam epitaxy and ferroelectric properties of Al1-xYxN thin films with Y composition up to x = 41%. Structural characterization reveals that a wurtzite lattice structure is well preserved despite the large lattice distortions induced by increasing Y content. Both the coercive field and remanent polarization show a strong dependence on Y composition. The coercive field varies from 5.5 to 2.8 MV/cm with increasing Y compositions from 10% to 41%, whereas the remanent polarization is reduced from 140 to 70 μC/cm2. These properties are further compared with previously reported AlScN and GaScN. This study establishes AlYN as a tunable ferroelectric ultrawide-bandgap semiconductor for next-generation electronic, photonic, and electromechanical devices.
- 27 July 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (4)
Composition-dependent ferroelectricity in epitaxial AlYN
We report molecular beam epitaxy and ferroelectric properties of Al1-xYxN thin films with Y composition up to x = 41%. Structural characterization reveals that a wurtzite lattice structure is well preserved despite the large lattice distortions induced by increasing Y content. Both the coercive field and remanent polarization show a strong dependence on Y composition. The coercive field varies from 5.5 to 2.8 MV/cm with increasing Y compositions from 10% to 41%, whereas the remanent polarization is reduced from 140 to 70 μC/cm2. These properties are further compared with previously reported AlScN and GaScN. This study establishes AlYN as a tunable ferroelectric ultrawide-bandgap semiconductor for next-generation electronic, photonic, and electromechanical devices.
- 25 May 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (21)
600 °C operation of MBE-enabled ScAlN/AlN/GaN FinHEMTs
We report Sc0.15Al0.85N/AlN/GaN fin high-electron-mobility transistors (FinHEMTs) with stable operation up to 600 °C, enabled by a nearly lattice-matched Sc0.15Al0.85N barrier grown by molecular beam epitaxy. The fin sidewalls provide additional electrostatic control, strengthening gate modulation and thereby reducing off-state current (Ioff) and gate leakage (IG), improving subthreshold swing (SS), and shifting the threshold voltage (VT) positively relative to planar devices. At room temperature, the FinHEMTs with a fin width (Wch) of 0.4 μm achieve an on/off current (Ion/Ioff) ratio of ∼107, an SS of ∼105 mV/dec, and an on-state current (Ion) of ∼330 mA/mm. The devices also exhibit strong thermal robustness, maintaining Ion of 110 mA/mm at a gate–source voltage (VGS) of 0 V and an Ion/Ioff ratio of 890 at 600 °C. These results establish ScAlN/AlN/GaN FinHEMTs as a promising platform for extreme-temperature electronics.
- 25 May 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (21)
600 °C operation of MBE-enabled ScAlN/AlN/GaN FinHEMTs
We report Sc0.15Al0.85N/AlN/GaN fin high-electron-mobility transistors (FinHEMTs) with stable operation up to 600 °C, enabled by a nearly lattice-matched Sc0.15Al0.85N barrier grown by molecular beam epitaxy. The fin sidewalls provide additional electrostatic control, strengthening gate modulation and thereby reducing off-state current (Ioff) and gate leakage (IG), improving subthreshold swing (SS), and shifting the threshold voltage (VT) positively relative to planar devices. At room temperature, the FinHEMTs with a fin width (Wch) of 0.4 μm achieve an on/off current (Ion/Ioff) ratio of ∼107, an SS of ∼105 mV/dec, and an on-state current (Ion) of ∼330 mA/mm. The devices also exhibit strong thermal robustness, maintaining Ion of 110 mA/mm at a gate–source voltage (VGS) of 0 V and an Ion/Ioff ratio of 890 at 600 °C. These results establish ScAlN/AlN/GaN FinHEMTs as a promising platform for extreme-temperature electronics.
- 6 April 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (14)
Electrically pumped AlGaN edge-emitting UV-B laser diodes grown by molecular beam epitaxy
Mid and deep ultraviolet (UV) laser diodes remain among the least explored devices in semiconductor optoelectronics, despite their importance for spectroscopy, biochemical sensing, disinfection, and emerging quantum photonics. Here, we demonstrate an electrically pumped AlGaN-based laser diode operating in the UV-B band (280–315 nm). The device is grown by molecular beam epitaxy on a single-crystal AlN substrate and fabricated in a ridge-waveguide geometry. The laser diode operates at 298.5 nm and exhibits a relatively low threshold current density of 3.4 kA/cm2. Clear non-linear light–current characteristics and pronounced spectral narrowing with a full width at half maximum of 0.2 nm are measured above the threshold.
- 6 April 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (14)
Electrically pumped AlGaN edge-emitting UV-B laser diodes grown by molecular beam epitaxy
Mid and deep ultraviolet (UV) laser diodes remain among the least explored devices in semiconductor optoelectronics, despite their importance for spectroscopy, biochemical sensing, disinfection, and emerging quantum photonics. Here, we demonstrate an electrically pumped AlGaN-based laser diode operating in the UV-B band (280–315 nm). The device is grown by molecular beam epitaxy on a single-crystal AlN substrate and fabricated in a ridge-waveguide geometry. The laser diode operates at 298.5 nm and exhibits a relatively low threshold current density of 3.4 kA/cm2. Clear non-linear light–current characteristics and pronounced spectral narrowing with a full width at half maximum of 0.2 nm are measured above the threshold.
- 14 July 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (2)
Sc-rich monocrystalline ScGaN grown by MBE exhibits attractive ferroelectric properties
The rapid and continuous evolution of Sc-based ferroelectric nitrides in recent years has necessitated the exploration of monocrystalline thin films with ever-increasing Sc composition to yield greatly enhanced ferroelectric, piezoelectric, and optical properties. ScGaN presents as a natural choice due to the predicted solubility of ScN being greater in GaN than in AlN. Thus, we report the MBE growth of monocrystalline phase-pure ScGaN films on GaN, with Sc compositions of up to 48%. Detailed characterization reveals that, despite large lattice mismatch with GaN, high surface and crystal quality can be obtained. Coercive fields ranging from 3 to 1.2 MV cm−1, among the lowest reported for ferroelectric nitrides, are observed. Moreover, the fatiguing characteristics of Sc-rich ScGaN show non-zero polarization remaining after 109 bipolar cycles. These results highlight the potential of Sc-rich ferroelectric nitrides to harness outstanding ferroelectric, piezoelectric, and photonic properties all on a nitride platform.
- 14 July 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (2)
Sc-rich monocrystalline ScGaN grown by MBE exhibits attractive ferroelectric properties
The rapid and continuous evolution of Sc-based ferroelectric nitrides in recent years has necessitated the exploration of monocrystalline thin films with ever-increasing Sc composition to yield greatly enhanced ferroelectric, piezoelectric, and optical properties. ScGaN presents as a natural choice due to the predicted solubility of ScN being greater in GaN than in AlN. Thus, we report the MBE growth of monocrystalline phase-pure ScGaN films on GaN, with Sc compositions of up to 48%. Detailed characterization reveals that, despite large lattice mismatch with GaN, high surface and crystal quality can be obtained. Coercive fields ranging from 3 to 1.2 MV cm−1, among the lowest reported for ferroelectric nitrides, are observed. Moreover, the fatiguing characteristics of Sc-rich ScGaN show non-zero polarization remaining after 109 bipolar cycles. These results highlight the potential of Sc-rich ferroelectric nitrides to harness outstanding ferroelectric, piezoelectric, and photonic properties all on a nitride platform.
- 6 January 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (1)
E-mode AlGaN/GaN HEMT with ScAlN/ScN charge trap-coupled ferroelectric gate stacks
A fully epitaxial ferroelectric ScAlN/AlGaN/GaN HEMT coupled with an ultrathin ScN charge trap layer for enhancement-mode operation is demonstrated. The ultrathin ScN acts as an electron reservoir to trap and store the electrons from the 2-dimensional electron gas channel region, transitioning the operation of the GaN high electron mobility transistor from the depletion-mode to the enhancement-mode, while the fully epitaxial nature enables low interface defect density and steep slope operation. The initialization process by applying a positive gate bias to inject carriers to the ScN layer is observed to shift the threshold voltage (Vth) from −1.2 to +1.3 V. The fabricated device also shows a steep subthreshold swing as low as 61 mV/dec and exhibits good stability, providing a promising pathway for power-efficient and multifunctional applications.
- 6 January 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (1)
E-mode AlGaN/GaN HEMT with ScAlN/ScN charge trap-coupled ferroelectric gate stacks
A fully epitaxial ferroelectric ScAlN/AlGaN/GaN HEMT coupled with an ultrathin ScN charge trap layer for enhancement-mode operation is demonstrated. The ultrathin ScN acts as an electron reservoir to trap and store the electrons from the 2-dimensional electron gas channel region, transitioning the operation of the GaN high electron mobility transistor from the depletion-mode to the enhancement-mode, while the fully epitaxial nature enables low interface defect density and steep slope operation. The initialization process by applying a positive gate bias to inject carriers to the ScN layer is observed to shift the threshold voltage (Vth) from −1.2 to +1.3 V. The fabricated device also shows a steep subthreshold swing as low as 61 mV/dec and exhibits good stability, providing a promising pathway for power-efficient and multifunctional applications.
- 18 November 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (21)
Effect of temperature on the performance of ScAlN/GaN high-electron mobility transistor
We have studied the operation of the ScAlN/GaN high-electron mobility transistor (HEMT) at high temperatures up to 700 K (423 °C). A maximum drain current density of ∼2 A/mm and an on-resistance of ∼1.5 Ω·mm was measured at room temperature (RT). The epi-structure exhibited a very high two-dimensional electron gas (2DEG) density of 6 × 1013 cm−2 at RT using Hall measurement. The Sc0.15Al0.85N barrier, nearly lattice matched to the GaN channel, showed a drain current reduction of ∼50% at 700 K. The decrease in 2DEG mobility, which leads to an increase in sheet resistance, is mostly responsible for this reduction in drain current. However, an excellent electrostatic control was achieved at 700 K with the drain current value exceeding 1 A/mm, which is 2 times higher compared to that of AlGaN/GaN HEMTs reported previously. These results indicate that ScAlN/GaN HEMTs are a promising candidate for high-temperature and high-power electronic applications.
- 18 November 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (21)
Effect of temperature on the performance of ScAlN/GaN high-electron mobility transistor
We have studied the operation of the ScAlN/GaN high-electron mobility transistor (HEMT) at high temperatures up to 700 K (423 °C). A maximum drain current density of ∼2 A/mm and an on-resistance of ∼1.5 Ω·mm was measured at room temperature (RT). The epi-structure exhibited a very high two-dimensional electron gas (2DEG) density of 6 × 1013 cm−2 at RT using Hall measurement. The Sc0.15Al0.85N barrier, nearly lattice matched to the GaN channel, showed a drain current reduction of ∼50% at 700 K. The decrease in 2DEG mobility, which leads to an increase in sheet resistance, is mostly responsible for this reduction in drain current. However, an excellent electrostatic control was achieved at 700 K with the drain current value exceeding 1 A/mm, which is 2 times higher compared to that of AlGaN/GaN HEMTs reported previously. These results indicate that ScAlN/GaN HEMTs are a promising candidate for high-temperature and high-power electronic applications.
- 24 June 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (26)
Rethinking polarization in wurtzite semiconductors
Polarization arising from non-centrosymmetric wurtzite lattice underpins the physics and functionality of gallium nitride (GaN)—the most produced semiconductor materials second only to silicon. However, recent direct experimental measurements unveiled remanent polarization of unexpectedly large magnitudes and opposite orientations to traditionally anticipated. This significant discrepancy not only poses a formidable challenge to our existing theoretical paradigms but also accentuates the need for a critical rethinking and methodological refinement to integrate these emerging observations with established knowledge, mitigating potential misunderstandings and misconceptions in this rapidly evolving field.
- 24 June 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (26)
Rethinking polarization in wurtzite semiconductors
Polarization arising from non-centrosymmetric wurtzite lattice underpins the physics and functionality of gallium nitride (GaN)—the most produced semiconductor materials second only to silicon. However, recent direct experimental measurements unveiled remanent polarization of unexpectedly large magnitudes and opposite orientations to traditionally anticipated. This significant discrepancy not only poses a formidable challenge to our existing theoretical paradigms but also accentuates the need for a critical rethinking and methodological refinement to integrate these emerging observations with established knowledge, mitigating potential misunderstandings and misconceptions in this rapidly evolving field.
- 6 May 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (19)
Molecular beam epitaxy and characterization of ferroelectric quaternary alloy Sc0.2Al0.45Ga0.35N
In this study, we demonstrate ferroelectricity in high-quality monocrystalline quaternary alloy ScAlGaN. Sc0.2Al0.45Ga0.35N films are grown by plasma-assisted molecular beam epitaxy and exhibit a surface roughness of 0.5 nm, limited by the roughness of the underlying molybdenum template. Polarization-electric field and positive-up-negative-down measurements reveal unambiguous ferroelectric switching with a coercive field of ∼5.5 MV cm−1 at 10 kHz and high remanent polarization of ∼150 μC cm−2. Time-dependent measurements suggest that the polarization reversal behavior adheres to the Kolmogorov–Avrami–Ishibashi model and follows a scheme of domain nucleation and growth. Detailed piezoresponse force microscopy studies further elucidate the evolution of polarity reversal domains in wurtzite nitride ferroelectrics and support the notion that the growth of inversion domains occurs via an in-plane motion of the domain walls. The realization of functional ferroelectric quaternary alloys in the wurtzite nitride family extends beyond being a technical demonstration. The additional degree of bandgap, band alignment, lattice parameter, and piezoelectric constant tunability achievable through quaternary alloys unveils a vast dimension through which wurtzite nitride ferroelectrics can be optimally engineered for a broad variety of high-performance electronic, optoelectronic, and acoustic devices and systems.
- 6 May 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (19)
Molecular beam epitaxy and characterization of ferroelectric quaternary alloy Sc0.2Al0.45Ga0.35N
In this study, we demonstrate ferroelectricity in high-quality monocrystalline quaternary alloy ScAlGaN. Sc0.2Al0.45Ga0.35N films are grown by plasma-assisted molecular beam epitaxy and exhibit a surface roughness of 0.5 nm, limited by the roughness of the underlying molybdenum template. Polarization-electric field and positive-up-negative-down measurements reveal unambiguous ferroelectric switching with a coercive field of ∼5.5 MV cm−1 at 10 kHz and high remanent polarization of ∼150 μC cm−2. Time-dependent measurements suggest that the polarization reversal behavior adheres to the Kolmogorov–Avrami–Ishibashi model and follows a scheme of domain nucleation and growth. Detailed piezoresponse force microscopy studies further elucidate the evolution of polarity reversal domains in wurtzite nitride ferroelectrics and support the notion that the growth of inversion domains occurs via an in-plane motion of the domain walls. The realization of functional ferroelectric quaternary alloys in the wurtzite nitride family extends beyond being a technical demonstration. The additional degree of bandgap, band alignment, lattice parameter, and piezoelectric constant tunability achievable through quaternary alloys unveils a vast dimension through which wurtzite nitride ferroelectrics can be optimally engineered for a broad variety of high-performance electronic, optoelectronic, and acoustic devices and systems.