Cal J. Rising
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Cal J. Rising has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Kareem Ahmed
Department of Mechanical and Aerospace Engineering, Center for Advanced Turbomachinery and Energy Research, University of Central Florida, Orlando, USA
5 shared publications Jonathan Sosa
2 shared publicationsMason Thornton
2 shared publications- Rachel Hytovick
Department of Mechanical and Aerospace Engineering, University of Central Florida 1 , Orlando, Florida 32828, USA
2 shared publications - Ryan Frederick Johnson
U.S. Naval Research Laboratory
2 shared publications Andrew La Sorsa
1 shared publication
Latest Publications
- 17 September 2026
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 42
Dynamic interactions of the compressible reacting flow with a morphing wall in a supersonic combustor
- 17 September 2026
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 42
Dynamic interactions of the compressible reacting flow with a morphing wall in a supersonic combustor
- 16 January 2026
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 11 (1)
Simulation of non-premixed, supersonic combustion using the discontinuous Galerkin method on fully unstructured grids
- 16 January 2026
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 11 (1)
Simulation of non-premixed, supersonic combustion using the discontinuous Galerkin method on fully unstructured grids
- 28 July 2023
- Published by Elsevier in Aerospace Science and Technology
- Vol. 141
Mean pressure gradient effects on the performance of ramjet cavity stabilized flames
- 28 July 2023
- Published by Elsevier in Aerospace Science and Technology
- Vol. 141
Mean pressure gradient effects on the performance of ramjet cavity stabilized flames
- 16 November 2022
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 39 (3) , 2817-2824
The effects of flame generated turbulence for turbulent-induced deflagration to detonation transition
- 16 November 2022
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 39 (3) , 2817-2824
The effects of flame generated turbulence for turbulent-induced deflagration to detonation transition
- 12 August 2022
- Published by Elsevier in Aerospace Science and Technology
- Vol. 129, 107805
Numerical investigation of turbulent flame-vortex interaction in premixed cavity stabilized flames
- 12 August 2022
- Published by Elsevier in Aerospace Science and Technology
- Vol. 129, 107805
Numerical investigation of turbulent flame-vortex interaction in premixed cavity stabilized flames
- Open Access
- 30 July 2021
- Published by ASME International in Journal of Fluids Engineering
- Vol. 144 (1)
Characteristics of a Single Sensor Fiber-Coupled Three-Dimensional Particle Image Velocimetry for Reacting Flow-Fields
Tomographic particle image velocimetry (Tomo-PIV) has become a standard tool for capturing a three-dimensional (3D) velocity fields in nonreacting flows. However, the diagnostic approach can become costly and challenging to implement when extended to applications which require high-speed cameras. This limitation has led to the use of fiber wound bundles to allow for multiple views to be captured on a single camera sensor. Additionally, employing this diagnostic approach on reacting flow-fields becomes more complex as the introduction of the flame causes additional luminosity and optical distortion which impacts the particle field reconstruction. This work seeks to validate and determine the limitations when utilizing a single sensor fiber-coupled approach for capturing Tomo-PIV data on a reacting flow-field. A premixed propane (C3H8) and air Bunsen burner flame is utilized to examine if the single sensor approach can meet the parameters for acceptable reconstruction based on previous research. The resulting velocity fields are then compared to a traditional PIV measurement to assess the deviation of the single sensor approach from a standard velocimetry measurement approach. It is demonstrated that there is strong agreement between the velocity and vorticity for the average flow-fields; however, when comparing the Reynolds shear stresses, a significant deviation is revealed. The deviation is attributed to strong velocity fluctuations occurring within the instantaneous Tomo-PIV data, which creates a significant divergence between the measurement techniques on an instantaneous basis. This demonstrates that while the approach can obtain reliable velocity and vorticity statistics, there are significant limitations in calculating second-order turbulence statistics. Thus, revealing that there is a tradeoff between the ability to extract the full velocity gradient tensor and the extent of the turbulence-related analysis which can be reliably performed.
- 30 July 2021
- Published by ASME International in Journal of Fluids Engineering
- Vol. 144 (1)
Open AccessCharacteristics of a Single Sensor Fiber-Coupled Three-Dimensional Particle Image Velocimetry for Reacting Flow-Fields
Tomographic particle image velocimetry (Tomo-PIV) has become a standard tool for capturing a three-dimensional (3D) velocity fields in nonreacting flows. However, the diagnostic approach can become costly and challenging to implement when extended to applications which require high-speed cameras. This limitation has led to the use of fiber wound bundles to allow for multiple views to be captured on a single camera sensor. Additionally, employing this diagnostic approach on reacting flow-fields becomes more complex as the introduction of the flame causes additional luminosity and optical distortion which impacts the particle field reconstruction. This work seeks to validate and determine the limitations when utilizing a single sensor fiber-coupled approach for capturing Tomo-PIV data on a reacting flow-field. A premixed propane (C3H8) and air Bunsen burner flame is utilized to examine if the single sensor approach can meet the parameters for acceptable reconstruction based on previous research. The resulting velocity fields are then compared to a traditional PIV measurement to assess the deviation of the single sensor approach from a standard velocimetry measurement approach. It is demonstrated that there is strong agreement between the velocity and vorticity for the average flow-fields; however, when comparing the Reynolds shear stresses, a significant deviation is revealed. The deviation is attributed to strong velocity fluctuations occurring within the instantaneous Tomo-PIV data, which creates a significant divergence between the measurement techniques on an instantaneous basis. This demonstrates that while the approach can obtain reliable velocity and vorticity statistics, there are significant limitations in calculating second-order turbulence statistics. Thus, revealing that there is a tradeoff between the ability to extract the full velocity gradient tensor and the extent of the turbulence-related analysis which can be reliably performed.