ACAna Cecília de Carvalho

Ana Cecília de Carvalho

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Ana Cecília de Carvalho has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Wear and rolling contact fatigue performance of forged railway wheels: The influence of microstructure and hardness ratio

    by Ana Cecília de Carvalho, Mário José-Bueno, Denilson Santos Monteiro, Rodrigo da Silva Miranda, Andrei Bavaresco Rezende, Noé Cheung, Paulo Roberto Mei

  • Open Access

    Effect of Vanadium Addition on the Wear Resistance and Rolling Contact Fatigue of Cast Class D Railway Wheels

    by Samuel Carlos Winiarski, Mário José-Bueno, Ana Cecília de Carvalho, Rodrigo da Silva Miranda, Denilson Santos Monteiro, Andrei Bavaresco Rezende, Noé Cheung, Paulo Roberto Mei

    Rail transport is one of the main freight transportation modes in Brazil, responsible for transporting about 92% of all extracted ore to ports via railways. However, it incurs high maintenance costs, exceeding $1.5 billion annually, with most of this amount allocated to rolling stock maintenance. This study investigates the influence of vanadium (V) microalloying on the wear and rolling contact fatigue (RCF) performance of cast Class D railway wheels. Using a twin-disc tribometer simulating wheel-rail contact, a vanadium-microalloyed wheel (CD-V) was compared against a conventional wheel (CD). Key parameters evaluated included mass loss, plastically deformed layer thickness, and crack characteristics. While the CD-V wheel showed slightly lower mass loss, the difference compared to the CD wheel was not statistically significant. However, the slightly increased hardness of the CD-V wheel seems to led to greater wear on the rail counterbody, indicating a trade-off. In contrast, vanadium addition demonstrated significant benefits for RCF resistance. The CD-V wheel exhibited a thinner plastically deformed subsurface layer and superior crack morphology, characterized by shorter surface cracks, lower-angle and shallower subsurface cracks. These RCF improvements suggest that vanadium microalloying in cast wheels could offer advantages in operations where shelling resistance is a primary concern.


  • Open Access

    Analysis of Wear in the Contact Between the Wheel Tread and the Rail Head: Influence of the Manufacturing Process of Cast and Forged Railway Wheels

    by V.G. Germinari, R.S. Miranda, A.B. Rezende, A.C. Carvalho, D.S. Monteiro, M. Jose-Bueno, R.C. Rocha, A. Sinatora, P.R. Mei

    In countries with continental dimensions like Brazil, railways transport production from inland regions to ports and the international market. It is essential to note that researchers and engineers in the railway sector are constantly striving to reduce operational and maintenance costs associated with wheel-rail contact while maintaining high standards of quality, safety, and operational predictability. In this context, wheels are one of the most costly components in railway acquisition and maintenance, representing a significant factor in transport safety. Additionally, their manufacturing process can involve either forging or casting. Therefore, the manufacturing process can offer the best cost-benefit ratio to meet the diverse demands of the railway sector — longer wear/fatigue life with lower costs. This study aimed to analyze the effects of the manufacturing process of the cast and forged microalloyed railway wheels, with similar microstructure, hardness, and equivalent carbon content, on the metallurgical defects formation and tribological properties. To support material characterization, optical microscopy, scanning electron microscopy, hardness measurements, ASTM E45 standards for evaluating metallurgical defects, twin-disc wear tests, Raman spectroscopy, and statistical analyses were conducted to compare the defects and cracks developed in railway steels.


  • Open Access

    Evaluation of the Cycle Count in Determining the Wear Rate of a Cast Wheel in Two Service Lives Using the Twin Disc Test

    by A.C. Carvalho, R.S. Miranda, M. Jose-Bueno, D.S. Monteiro, A.B. Rezende, G.A. Santos, N. Cheung, P.R. Mei

    This study aims to evaluate the wear and rolling contact fatigue performance of two lives of the same railway wheel: one with a bainitic microstructure and the other with a pearlitic microstructure, both tested against the same commercial premium rail. Tests were conducted using a Twin Disc tribometer. The results demonstrated that bainite exhibits superior wear resistance, with a 34% lower mass loss compared to pearlite under identical conditions. Additionally, the bainitic microstructure showed greater resistance to rolling contact fatigue, as surface cracks were smaller in size compared to those observed in the pearlitic microstructure. The counterbody also performed better when tested against the bainitic specimen.


  • Effect of grease viscosity and thickener on the wear resistance of a class D railway wheel

    by Ana Cecilia de Carvalho, Andrei Bavaresco Rezende, Fernanda de Melo Fernandes, Rodrigo da Silva Miranda, Edilson Jun Kina, Tiago Cousseau, Paulo Roberto Mei


  • Electrochemical characterisation of dental alloys: its possibilities and limitations

    by Wolf-Dieter Mueller, C. Schoepf, M. L. Nascimento, A. C. Carvalho, M. Moisel, A. Schenk, F. Scholz, K. P. Lange

    Dental alloys are metallic biomaterials which have a broad variation of composition compared to technical alloys. It is therefore in the interest of patients and technicians to conduct a good assessment of the electrochemical behaviour of dental alloys in order to collect information about their corrosion resistance. The purpose of this work was to demonstrate possibilities and limitations of two electrochemical techniques: the voltammetry of immobilised microparticles (ViMP) onto lead, and cyclic voltammetry measurements with the help of the mini-cell system (MCS). Based on fingerprints obtained from ViMP it was possible to analyse and differentiate the dental alloys. The results obtained by MCS were comparable with ViMP, but give a better understanding of the corrosion behaviour of the materials.