Habeeb Bello
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Habeeb Bello has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Aliyu Danjuma Usman
Ahmadu Bello University
2 shared publications - Kabir Ahmad Abubilal
Ahmadu Bello University
2 shared publications Abdoulie M.S. Tekanyi
1 shared publicationAbdulmalik Shehu Yaro
1 shared publication- Abdulmalik Shehu Yaro
Department of Informatics and Quantitative Methods, Faculty of Informatics and Management, University of Hradec Krlov, Hradec Kralove, Czech Republic
1 shared publication - Ahmed Tijani Salawudeen
Department of Electrical and Electronic Engineering, University of Jos, Jos 93000, Nigeria
1 shared publication
Latest Publications
- Open Access
- 1 August 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Informatics and Communication Technology (IJ-ICT)
- Vol. 12 (2) , 103-114
Design of a 175 GHZ SiGe-based voltage-controlled oscillator with greater than 7.6 dBm power
In this research, we present a low phase noise (PN) and wide tuning range 175 GHz inductors and capacitors (LC) voltage-controlled oscillator (VCO) based on a differential Colpitts oscillator that was designed using a 0.13 μm bipolar complementary metal oxide semiconductor (BiCMOS) and simulated. The square of the tank Q-factor and the square of the oscillation amplitude were both maximized to reduce PN. With an extensive examination of parasitic, mathematical analysis of load impedances, and implementation of differential design, the PN was reduced, and the output power was enhanced. Using a supply voltage of 1.6 V, the VCO consumes 41.9 mA, resulting in a total power usage of 67 mW to prevent undesirable PN deterioration, an inter-stage LC filter at the VCO-buffer interface increases the swing at the buffer input. To make a better output, a buffer is used to isolate the load from the VCO core. In addition, the VCO has a high linearity and the overall, the VCO presented in this study demonstrates excellent performance and has the potential to be used in a wide range of applications that require a high-performance, low-power VCO.
- 1 August 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Informatics and Communication Technology (IJ-ICT)
- Vol. 12 (2) , 103-114
Open AccessDesign of a 175 GHZ SiGe-based voltage-controlled oscillator with greater than 7.6 dBm power
In this research, we present a low phase noise (PN) and wide tuning range 175 GHz inductors and capacitors (LC) voltage-controlled oscillator (VCO) based on a differential Colpitts oscillator that was designed using a 0.13 μm bipolar complementary metal oxide semiconductor (BiCMOS) and simulated. The square of the tank Q-factor and the square of the oscillation amplitude were both maximized to reduce PN. With an extensive examination of parasitic, mathematical analysis of load impedances, and implementation of differential design, the PN was reduced, and the output power was enhanced. Using a supply voltage of 1.6 V, the VCO consumes 41.9 mA, resulting in a total power usage of 67 mW to prevent undesirable PN deterioration, an inter-stage LC filter at the VCO-buffer interface increases the swing at the buffer input. To make a better output, a buffer is used to isolate the load from the VCO core. In addition, the VCO has a high linearity and the overall, the VCO presented in this study demonstrates excellent performance and has the potential to be used in a wide range of applications that require a high-performance, low-power VCO.
- Open Access
- 1 August 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 13 (4) , 4194-4203
Drone’s node placement algorithm with routing protocols to enhance surveillance
Flying ad-hoc network (FANET) is characterized by key component features such as communication scheme, energy awareness, and task distribution. In this research, a surveillance space considering standard petroleum pipe was created with three drones viz: drone 1 (D1), master drone (DM), and drone 2 (D2) to survey as FANET. DM aggregate packets from D1, D2 and communicate with the static ground control station (SGCS). The starting point of the three drones and their trajectories during deployment were calculated and simulated. Selection of DM, D1, and D2 was done using battery level before take-off. Simulation results show take-off time difference which depends on the distance of each drone to the SGCS during deployment. D1 take-off first, while DM and D2 followed after 0.0704 and 0.1314 ms respectively. The position-oriented routing protocols results indicated variation of information flow within time notch due to variation in the density of the transmitted packets. Packets delivery periods are 0.00136×103 sec, 0.00110×103 sec, and 0.00246×103 sec for time notch 1, 2, and aggregating time notch respectively. From the results obtained, two algorithms were used successfully in deploying the drones
- 1 August 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 13 (4) , 4194-4203
Open AccessDrone’s node placement algorithm with routing protocols to enhance surveillance
Flying ad-hoc network (FANET) is characterized by key component features such as communication scheme, energy awareness, and task distribution. In this research, a surveillance space considering standard petroleum pipe was created with three drones viz: drone 1 (D1), master drone (DM), and drone 2 (D2) to survey as FANET. DM aggregate packets from D1, D2 and communicate with the static ground control station (SGCS). The starting point of the three drones and their trajectories during deployment were calculated and simulated. Selection of DM, D1, and D2 was done using battery level before take-off. Simulation results show take-off time difference which depends on the distance of each drone to the SGCS during deployment. D1 take-off first, while DM and D2 followed after 0.0704 and 0.1314 ms respectively. The position-oriented routing protocols results indicated variation of information flow within time notch due to variation in the density of the transmitted packets. Packets delivery periods are 0.00136×103 sec, 0.00110×103 sec, and 0.00246×103 sec for time notch 1, 2, and aggregating time notch respectively. From the results obtained, two algorithms were used successfully in deploying the drones
- Open Access
- 30 June 2023
- Published by GSC Online Press in Global Journal of Engineering and Technology Advances
- Vol. 15 (3) , 096-106
Investigation and design methods of a compact patch antennas using 3-D MMIC for various applications
This work focused on the design, characterization and investigation of GaAs based multi-layered compact 3D MMIC based antenna. Different patch antennas were designed and characterized along with its S-parameters. Two proposed models of multi-layered patch antenna using V-shaped feeder line and planar feeder line with a spiral transmission line in metal-2 were more compact in size and showed an improvement in performance based on bandwidth compared to the traditional planar feeder line configuration. This implies the proposed planar feed line with the spiral transmission is cost effective. The newly propose planar antenna with a spiral transmission feeder line is 49% more compact in area compared to using the normal planar feeder line. The new design also has wider bandwidth with a bandwidth of 2.99% as compared to the traditional planar with a bandwidth of 1.93%, better input return loss and a slightly lower resonance frequency. Similarly, another multilayer patch antenna was proposed using a V-shaped feeder line, This V-shaped feeder line antenna model showed a much lower resonance frequency (36.50 GHz) compared to normal planar (38.92GHz) and the planar with spiral transmission line model (38.52 GHz).
- 30 June 2023
- Published by GSC Online Press in Global Journal of Engineering and Technology Advances
- Vol. 15 (3) , 096-106
Open AccessInvestigation and design methods of a compact patch antennas using 3-D MMIC for various applications
This work focused on the design, characterization and investigation of GaAs based multi-layered compact 3D MMIC based antenna. Different patch antennas were designed and characterized along with its S-parameters. Two proposed models of multi-layered patch antenna using V-shaped feeder line and planar feeder line with a spiral transmission line in metal-2 were more compact in size and showed an improvement in performance based on bandwidth compared to the traditional planar feeder line configuration. This implies the proposed planar feed line with the spiral transmission is cost effective. The newly propose planar antenna with a spiral transmission feeder line is 49% more compact in area compared to using the normal planar feeder line. The new design also has wider bandwidth with a bandwidth of 2.99% as compared to the traditional planar with a bandwidth of 1.93%, better input return loss and a slightly lower resonance frequency. Similarly, another multilayer patch antenna was proposed using a V-shaped feeder line, This V-shaped feeder line antenna model showed a much lower resonance frequency (36.50 GHz) compared to normal planar (38.92GHz) and the planar with spiral transmission line model (38.52 GHz).