Yan Yuan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yan Yuan has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Song Xu
Fuzhou Univ
5 shared publications Bin Xue
3 shared publicationsHongyu Chen
Department of Road and Bridge Engineering, College of Civil Engineering, Fuzhou University 1 , No. 2 Xueyuan Rd., Fuzhou, Fujian 350108
3 shared publicationsBaizhang Wu
2 shared publicationsChaoyang Sun
2 shared publicationsGuilian Zou
2 shared publications
Latest Publications
- Open Access
- 1 September 2026
- Published by Elsevier in SSRN Electronic Journal
Water Transport Governs the Volumetric Stability of Steel Slag: A Multiscale Mechanistic Comparison of Three Surface Modification Strategies
Steel slag has attracted increasing attention as a sustainable construction material; however, continuous hydration of free calcium oxide (f-CaO) causes undesirable volumetric expansion that compromises its engineering performance. In this study, three surface modification strategies—an epoxy silicone resin coating, a cement–silica fume system, and a silica fume treatment—were developed to construct hydrophobic-barrier, hydration-consolidation, and pore-refinement systems, respectively, regulating water transport and enhancing the volumetric stability of steel slag. The modification mechanisms were investigated using scanning electron microscopy (SEM), water contact angle measurement, Brunauer–Emmett–Teller (BET) pore analysis, X-ray computed tomography (XCT), X-ray diffraction (XRD), thermogravimetric analysis (TG–DTG), and immersion expansion tests. All strategies improved the surface characteristics of steel slag and reduced water transport, with the epoxy silicone resin performing best: it formed a continuous hydrophobic coating that reduced water absorption and immersion expansion by 43% and 56%, respectively. The cement-based modification enhanced interfacial stability via calcium silicate hydrate (C–S–H) gel formation, while the silica fume treatment optimized the pore structure through micro-filling and pozzolanic reactions. The results further show that volumetric stability is jointly governed by water transport and residual f-CaO content, and that when f-CaO cannot be fully eliminated, suppressing water transport through interfacial modification plays the more dominant role in mitigating expansion. Blocking water transport pathways therefore represents an effective strategy for improving the long-term stability and engineering performance of steel slag.
- 1 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessWater Transport Governs the Volumetric Stability of Steel Slag: A Multiscale Mechanistic Comparison of Three Surface Modification Strategies
Steel slag has attracted increasing attention as a sustainable construction material; however, continuous hydration of free calcium oxide (f-CaO) causes undesirable volumetric expansion that compromises its engineering performance. In this study, three surface modification strategies—an epoxy silicone resin coating, a cement–silica fume system, and a silica fume treatment—were developed to construct hydrophobic-barrier, hydration-consolidation, and pore-refinement systems, respectively, regulating water transport and enhancing the volumetric stability of steel slag. The modification mechanisms were investigated using scanning electron microscopy (SEM), water contact angle measurement, Brunauer–Emmett–Teller (BET) pore analysis, X-ray computed tomography (XCT), X-ray diffraction (XRD), thermogravimetric analysis (TG–DTG), and immersion expansion tests. All strategies improved the surface characteristics of steel slag and reduced water transport, with the epoxy silicone resin performing best: it formed a continuous hydrophobic coating that reduced water absorption and immersion expansion by 43% and 56%, respectively. The cement-based modification enhanced interfacial stability via calcium silicate hydrate (C–S–H) gel formation, while the silica fume treatment optimized the pore structure through micro-filling and pozzolanic reactions. The results further show that volumetric stability is jointly governed by water transport and residual f-CaO content, and that when f-CaO cannot be fully eliminated, suppressing water transport through interfacial modification plays the more dominant role in mitigating expansion. Blocking water transport pathways therefore represents an effective strategy for improving the long-term stability and engineering performance of steel slag.
- 20 January 2026
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 54 (4)
Performance and Micromechanism Analysis of a Terminal Blend Composite-Modified Asphalt
This article investigates the characteristics and micromodification mechanisms of terminal blend (TB) composite–modified asphalts. The physical properties, micromorphologies, chemical functional groups, and thermal stabilities of the TB composite–modified asphalts are elucidated using various analytical techniques (physical property indices, fluorescence microscopy, infrared spectroscopy, and thermogravimetric analysis). The asphalts prepared from two formulations TB_5 % styrene butadiene styrene (SBS) + 1 % aromatics + 0.1 % sulfur and TB_3 % SBS + 3 % ethylene vinyl acetate (EVA) + 1 % aromatics + 0.1 % sulfur—demonstrate superior high- and low-temperature performance, along with moderate viscosity. On the microscopic level, the TB-modified asphalt containing 5 % SBS (TB_5S) forms a distinct crosslinked mesh structure surrounding a core of evenly interwoven black rubber particles. This structure largely enhances the asphalt performance. TB_5S also exhibits the highest short-term aging resistance among the samples. Under expansion and contraction vibrations of the carbon base, the TB-modified asphalt containing 5 % EVA (TB_5E) shows the highest degree of aging, whereas TB_5S shows the lowest. Although the SBS or EVA modifier alone can augment the thermal stability of the asphalt, adding both modifiers interfere with the modifier-asphalt interaction. This phenomenon explains the lowered thermal stability of the TB-modified asphalt containing 3 % SBS and 3 % EVA (TB_3S3E).
- 20 January 2026
- Published by ASTM International in Journal of Testing and Evaluation
- Vol. 54 (4)
Performance and Micromechanism Analysis of a Terminal Blend Composite-Modified Asphalt
This article investigates the characteristics and micromodification mechanisms of terminal blend (TB) composite–modified asphalts. The physical properties, micromorphologies, chemical functional groups, and thermal stabilities of the TB composite–modified asphalts are elucidated using various analytical techniques (physical property indices, fluorescence microscopy, infrared spectroscopy, and thermogravimetric analysis). The asphalts prepared from two formulations TB_5 % styrene butadiene styrene (SBS) + 1 % aromatics + 0.1 % sulfur and TB_3 % SBS + 3 % ethylene vinyl acetate (EVA) + 1 % aromatics + 0.1 % sulfur—demonstrate superior high- and low-temperature performance, along with moderate viscosity. On the microscopic level, the TB-modified asphalt containing 5 % SBS (TB_5S) forms a distinct crosslinked mesh structure surrounding a core of evenly interwoven black rubber particles. This structure largely enhances the asphalt performance. TB_5S also exhibits the highest short-term aging resistance among the samples. Under expansion and contraction vibrations of the carbon base, the TB-modified asphalt containing 5 % EVA (TB_5E) shows the highest degree of aging, whereas TB_5S shows the lowest. Although the SBS or EVA modifier alone can augment the thermal stability of the asphalt, adding both modifiers interfere with the modifier-asphalt interaction. This phenomenon explains the lowered thermal stability of the TB-modified asphalt containing 3 % SBS and 3 % EVA (TB_3S3E).
- Open Access
- 7 December 2025
- Published by MDPI AG in Infrastructures
- Vol. 10 (12) , 336
Effect of Bonding Characteristics on Rutting Resistance and Moisture Susceptibility of Rubberized Reclaimed Asphalt Pavement
Asphalt pavements incorporating recycled and sustainable materials have become a widely adopted strategy in road construction, particularly with the use of reclaimed asphalt pavement (RAP) and crumb rubber (CR) derived from waste tires. However, the adhesion and cohesion characteristics of rubberized RAP mixtures remain insufficiently understood. This study investigates how interfacial bonding affects the rutting resistance and moisture susceptibility of rubberized RAP asphalt mixtures. Two RAP sources with different aging levels and two CR particle sizes (250 μm and 380 μm) were evaluated. Binder bond strength (BBS) tests showed that pull-off strength increased with the use of smaller CR particles and more highly aged RAP, while rotational viscosity and penetration tests confirmed the corresponding increase in binder stiffness. Hamburg wheel track (HWT) tests with high-temperature viscoplastic deformation analysis demonstrated improved rutting resistance in the tested mixtures. Furthermore, boiling tests supported by image analysis revealed reductions in stripping ratios, indicating enhanced moisture resistance. ANOVA results (p < 0.05) confirmed that CR content had a significant effect on bonding characteristics, whereas RAP aging and CR particle size jointly influenced rutting performance. Overall, mixtures incorporating 10% CR and 25% RAP achieved the best balance between adhesion, cohesion, and durability. These findings provide a quantitative understanding of how interfacial bonding governs the mechanical performance and moisture resistance of rubberized RAP mixtures.
- 7 December 2025
- Published by MDPI AG in Infrastructures
- Vol. 10 (12) , 336
Open AccessEffect of Bonding Characteristics on Rutting Resistance and Moisture Susceptibility of Rubberized Reclaimed Asphalt Pavement
Asphalt pavements incorporating recycled and sustainable materials have become a widely adopted strategy in road construction, particularly with the use of reclaimed asphalt pavement (RAP) and crumb rubber (CR) derived from waste tires. However, the adhesion and cohesion characteristics of rubberized RAP mixtures remain insufficiently understood. This study investigates how interfacial bonding affects the rutting resistance and moisture susceptibility of rubberized RAP asphalt mixtures. Two RAP sources with different aging levels and two CR particle sizes (250 μm and 380 μm) were evaluated. Binder bond strength (BBS) tests showed that pull-off strength increased with the use of smaller CR particles and more highly aged RAP, while rotational viscosity and penetration tests confirmed the corresponding increase in binder stiffness. Hamburg wheel track (HWT) tests with high-temperature viscoplastic deformation analysis demonstrated improved rutting resistance in the tested mixtures. Furthermore, boiling tests supported by image analysis revealed reductions in stripping ratios, indicating enhanced moisture resistance. ANOVA results (p < 0.05) confirmed that CR content had a significant effect on bonding characteristics, whereas RAP aging and CR particle size jointly influenced rutting performance. Overall, mixtures incorporating 10% CR and 25% RAP achieved the best balance between adhesion, cohesion, and durability. These findings provide a quantitative understanding of how interfacial bonding governs the mechanical performance and moisture resistance of rubberized RAP mixtures.
- 29 October 2025
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 40 (5) , 1372-1378
Self-healing Mechanism of Asphalt: Molecular Modeling and Shear-healing Test
- 29 October 2025
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 40 (5) , 1372-1378
Self-healing Mechanism of Asphalt: Molecular Modeling and Shear-healing Test
- Open Access
Comparative Analysis of Strength Improvement Techniques in Perforated Glass Fiber Reinforced Polymer Plates: Adhesive Filling, Bolt Reinforcement, and Elliptical Perforation Design
Due to their high strength-to-weight ratio and corrosion resistance, glass fiber reinforced polymer (GFRP) composites have been used in various civil structures. However, the GFRP profiles may be perforated to allow bolting, wiring, and pipelining, causing stress concentration and safety concerns in load-carrying scenarios. A fundamental understanding of the stress concentration mechanisms and the efficacy of mitigation techniques in such anisotropic materials remains limited, particularly for the complex stress states introduced by perforations and mechanical fasteners. This study investigates the effectiveness of three techniques, adhesive filling, bolt reinforcement, and elliptical perforation design, in mitigating stress concentration and enhancing the strength of perforated GFRP plates. The effects of perforation geometry, filler modulus, bolt types, and applied preloads on the stress concentration and bearing capacity are investigated through experimental and finite element analysis. The results reveal that steel bolt reinforcement significantly improves load-bearing capacity, achieving a 13.9% increase in the pultrusion direction and restoring nearly full strength in the transverse direction (4.91 kN vs. unperforated 4.89 kN). Adhesive filling shows limited effectiveness, with minimal load improvement, while elliptical perforations exhibit the lowest performance, reducing strength by 38% compared to circular holes. Stress concentration factors (SCF) vary with hole diameter, peaking at 5.13 for 8 mm holes in the pultrusion direction, and demonstrate distinct sensitivity to filler modulus, with optimal SCF reduction observed at 30–40 GPa. The findings highlight the anisotropic nature of GFRP, emphasizing the importance of reinforcement selection based on loading direction and structural requirements. This study provides critical insights for optimizing perforated GFRP components in modular construction and other civil engineering applications.
Open AccessComparative Analysis of Strength Improvement Techniques in Perforated Glass Fiber Reinforced Polymer Plates: Adhesive Filling, Bolt Reinforcement, and Elliptical Perforation Design
Due to their high strength-to-weight ratio and corrosion resistance, glass fiber reinforced polymer (GFRP) composites have been used in various civil structures. However, the GFRP profiles may be perforated to allow bolting, wiring, and pipelining, causing stress concentration and safety concerns in load-carrying scenarios. A fundamental understanding of the stress concentration mechanisms and the efficacy of mitigation techniques in such anisotropic materials remains limited, particularly for the complex stress states introduced by perforations and mechanical fasteners. This study investigates the effectiveness of three techniques, adhesive filling, bolt reinforcement, and elliptical perforation design, in mitigating stress concentration and enhancing the strength of perforated GFRP plates. The effects of perforation geometry, filler modulus, bolt types, and applied preloads on the stress concentration and bearing capacity are investigated through experimental and finite element analysis. The results reveal that steel bolt reinforcement significantly improves load-bearing capacity, achieving a 13.9% increase in the pultrusion direction and restoring nearly full strength in the transverse direction (4.91 kN vs. unperforated 4.89 kN). Adhesive filling shows limited effectiveness, with minimal load improvement, while elliptical perforations exhibit the lowest performance, reducing strength by 38% compared to circular holes. Stress concentration factors (SCF) vary with hole diameter, peaking at 5.13 for 8 mm holes in the pultrusion direction, and demonstrate distinct sensitivity to filler modulus, with optimal SCF reduction observed at 30–40 GPa. The findings highlight the anisotropic nature of GFRP, emphasizing the importance of reinforcement selection based on loading direction and structural requirements. This study provides critical insights for optimizing perforated GFRP components in modular construction and other civil engineering applications.
- 5 February 2024
- Published by Springer Nature in International Journal of Pavement Research and Technology
- Vol. 18 (5) , 1239-1251
A Novel Approach Based on Munsell Value for the Evaluation of Asphalt Aging Degree
- 5 February 2024
- Published by Springer Nature in International Journal of Pavement Research and Technology
- Vol. 18 (5) , 1239-1251
A Novel Approach Based on Munsell Value for the Evaluation of Asphalt Aging Degree
- 1 October 2023
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 38 (5) , 1096-1104
The Research for Surface Properties of Steel Slag Powder and High-Temperature Rheological Properties of Asphalt Mortar
- 1 October 2023
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 38 (5) , 1096-1104
The Research for Surface Properties of Steel Slag Powder and High-Temperature Rheological Properties of Asphalt Mortar
- 10 August 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 400
How calcium and magnesium ions affect the stability of asphalt with anionic emulsifiers: A molecular dynamics study
- 10 August 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 400
How calcium and magnesium ions affect the stability of asphalt with anionic emulsifiers: A molecular dynamics study