Ning Ding
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ning Ding has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Afriyanti Sumboja
Material Science and Engineering Research Group, Faculty of Mechanical and Aerospace Engineering, Institut Teknologi Bandung, Jl. Ganesa 10, Bandung, 40132, Indonesia
3 shared publications - Naufal Hanif Hawari
School of Materials Science and Engineering Nanyang Technological University Singapore Singapore
3 shared publications - Achmad Prayogi
Material Science and Engineering Research Group, Faculty of Mechanical and Aerospace, Institut Teknologi Bandung, Jl. Ganesha 10, Bandung 40132, Indonesia
1 shared publication - Aldan Hadziq Haidar
Material Science and Engineering Research Group, Faculty of Mechanical and Aerospace Engineering, Institut Teknologi Bandung, Jl. Ganesa 10, Bandung 40132, Indonesia
1 shared publication - Changyun Jiang
Institute of Materials Research and Engineering (IMRE), Agency for Science, Technology and Research (A*Star), Singapore, Republic of Singapore
1 shared publication - Coryl Jing Jun Lee
Institute of Materials Research and Engineering (IMRE), Agency for Science, Technology and Research (A*STAR), 2 Fusionopolis Way, Innovis #08-03, Singapore 138634, Singapore
1 shared publication
Latest Publications
- Open Access
- 29 October 2026
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 18 (41) , 22662-22669
A self-assembled monolayer regulates solid electrolyte interphase formation in anode-free lithium metal batteries
Directing anion decomposition via a molecular monolayer promotes an inorganic-rich interphase and dense lithium deposition, improving cycling stability of anode-free lithium metal batteries.
- 29 October 2026
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 18 (41) , 22662-22669
Open AccessA self-assembled monolayer regulates solid electrolyte interphase formation in anode-free lithium metal batteries
Directing anion decomposition via a molecular monolayer promotes an inorganic-rich interphase and dense lithium deposition, improving cycling stability of anode-free lithium metal batteries.
- 8 April 2026
- Published by Elsevier in Energy Storage Materials
- Vol. 88
Quantitative decoupling of concurrent ion-storage mechanisms in aqueous Zn-ion batteries
- 8 April 2026
- Published by Elsevier in Energy Storage Materials
- Vol. 88
Quantitative decoupling of concurrent ion-storage mechanisms in aqueous Zn-ion batteries
- 6 February 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (20) , 12449-12460
PVDF nanofiber separator with sustained LiNO 3 additive release for dendrite-suppressed anode-free lithium metal batteries
Sustained additive release from the PP/PVDF/LiNO 3 separator overcomes LiNO 3 insolubility, enabling dendrite-suppressed anode-free batteries.
- 6 February 2026
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 14 (20) , 12449-12460
PVDF nanofiber separator with sustained LiNO 3 additive release for dendrite-suppressed anode-free lithium metal batteries
Sustained additive release from the PP/PVDF/LiNO 3 separator overcomes LiNO 3 insolubility, enabling dendrite-suppressed anode-free batteries.
- 16 August 2024
- Published by Wiley in Advanced Energy Materials
- Vol. 14 (40)
Revealing Phase Transitions in Poly(Ethylene Oxide)‐Based Electrolyte for Room‐Temperature Solid‐State Batteries
Solid‐state electrolytes (SSEs) offer enhanced safety, extended cycle life, and increased energy density when replacing flammable liquid electrolytes in lithium‐ion batteries. Poly(ethylene oxide) (PEO)‐based SSE is the only candidate that has been commercially implemented in electric vehicles. However, the equipped battery needs to operate at temperatures above 50 °C, and its phase transitions at room temperature are still unclear. Herein, the solidification of the PEO‐lithium bis(trifluoromethanesulfonyl)imide (PEOn‐LiTFSI) system is revisited. Contrary to the prevailing view of forming PEO(6)‐LiTFSI spherulites, the presence of crystalline PEO(8)‐LiTFSI complexes is quantitatively confirmed. The nucleation and growth processes of crystalline PEO and PEO(8)‐LiTFSI spherulites are also visually elucidated, and phase transitions with the impedance change are correlated. In addition, it is demonstrated that the crystalline PEO shell surrounding the PEO(8)‐LiTFSI spherulites hinders the kinetics of crystal growth, thereby enabling the highest ionic conductivity at n = 10. Importantly, it is pointed out that instead of the poor ionic conductivity of the electrolyte layer, the heterogeneous nucleation of PEO(8)‐LiTFSI within the electrodes is the limiting factor in constructing room‐temperature all‐solid‐state batteries.
- 16 August 2024
- Published by Wiley in Advanced Energy Materials
- Vol. 14 (40)
Revealing Phase Transitions in Poly(Ethylene Oxide)‐Based Electrolyte for Room‐Temperature Solid‐State Batteries
Solid‐state electrolytes (SSEs) offer enhanced safety, extended cycle life, and increased energy density when replacing flammable liquid electrolytes in lithium‐ion batteries. Poly(ethylene oxide) (PEO)‐based SSE is the only candidate that has been commercially implemented in electric vehicles. However, the equipped battery needs to operate at temperatures above 50 °C, and its phase transitions at room temperature are still unclear. Herein, the solidification of the PEO‐lithium bis(trifluoromethanesulfonyl)imide (PEOn‐LiTFSI) system is revisited. Contrary to the prevailing view of forming PEO(6)‐LiTFSI spherulites, the presence of crystalline PEO(8)‐LiTFSI complexes is quantitatively confirmed. The nucleation and growth processes of crystalline PEO and PEO(8)‐LiTFSI spherulites are also visually elucidated, and phase transitions with the impedance change are correlated. In addition, it is demonstrated that the crystalline PEO shell surrounding the PEO(8)‐LiTFSI spherulites hinders the kinetics of crystal growth, thereby enabling the highest ionic conductivity at n = 10. Importantly, it is pointed out that instead of the poor ionic conductivity of the electrolyte layer, the heterogeneous nucleation of PEO(8)‐LiTFSI within the electrodes is the limiting factor in constructing room‐temperature all‐solid‐state batteries.
- Open Access
- 21 August 2023
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 13 (36) , 25673-25680
Understanding SEI evolution during the cycling test of anode-free lithium-metal batteries with LiDFOB salt
Anode-free lithium-metal batteries (AFLMBs) have the potential to double the energy density of Li-ion batteries, but face the challenges of mossy dendritic lithium plating and an unstable solid electrolyte interphase (SEI). Previous studies have shown that the AFLMBs with an electrolyte containing lithium difluoro(oxalato)borate (LiDFOB) salt outperform those with lithium hexafluorophosphate (LiPF6), but the mechanism behind this improvement is not fully understood. In this study, X-ray photoelectron spectroscopy (XPS) depth profile analysis and electrochemical impedance spectroscopy (EIS) were conducted to investigate the SEI on plated Li from the two conducting salts and their evolution in Cu‖NMC full cells during cycling. XPS results revealed that an inorganic-rich SEI layer is formed in the cell with LiDFOB-based electrolyte, with a low carbon/oxygen ratio of 0.56 compared to 1.42 in the LiPF6-based cell. With the inorganic-rich SEI, a dense electroplated Li with a shining surface on the Cu substrate can be retained after ten cycles. The inorganic-rich SEI enhances the reversibility of Li plating and stripping, with a high average CE of ∼98% and a stable charge/discharge voltage profile. The changes in SEI resistance and cathode electrolyte interphase resistance are more prominent compared to the changes in solution and charge transfer resistances, which further validate the role of the passivation films on Li deposits and NMC cathode surfaces in stabilizing AFLMB cycling performance.
- 21 August 2023
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 13 (36) , 25673-25680
Open AccessUnderstanding SEI evolution during the cycling test of anode-free lithium-metal batteries with LiDFOB salt
Anode-free lithium-metal batteries (AFLMBs) have the potential to double the energy density of Li-ion batteries, but face the challenges of mossy dendritic lithium plating and an unstable solid electrolyte interphase (SEI). Previous studies have shown that the AFLMBs with an electrolyte containing lithium difluoro(oxalato)borate (LiDFOB) salt outperform those with lithium hexafluorophosphate (LiPF6), but the mechanism behind this improvement is not fully understood. In this study, X-ray photoelectron spectroscopy (XPS) depth profile analysis and electrochemical impedance spectroscopy (EIS) were conducted to investigate the SEI on plated Li from the two conducting salts and their evolution in Cu‖NMC full cells during cycling. XPS results revealed that an inorganic-rich SEI layer is formed in the cell with LiDFOB-based electrolyte, with a low carbon/oxygen ratio of 0.56 compared to 1.42 in the LiPF6-based cell. With the inorganic-rich SEI, a dense electroplated Li with a shining surface on the Cu substrate can be retained after ten cycles. The inorganic-rich SEI enhances the reversibility of Li plating and stripping, with a high average CE of ∼98% and a stable charge/discharge voltage profile. The changes in SEI resistance and cathode electrolyte interphase resistance are more prominent compared to the changes in solution and charge transfer resistances, which further validate the role of the passivation films on Li deposits and NMC cathode surfaces in stabilizing AFLMB cycling performance.
- 26 February 2018
- Published by Wiley in Chemnanomat
- Vol. 4 (4) , 394-400
Fabrication of Mesoporous Titania Nanoparticles with Controlled Porosity and Connectivity for Studying the Photovoltaic Properties in Perovskite Solar Cells
Mesoporous titania (TiO2) nanoparticles (NPs) were synthesized by treating prehydrolyzed titanium precursors with polyethylene glycol (PEG). By varying the amount of PEG, their different physical properties were tuned appropriately in terms of surface area, pore size/volume, and electrical conductivity. By increasing the amount of PEG in TiO2, the surface area and pore volume of mesoporous TiO2 increased, and no direct correlation with the photovoltaic performance of perovskite solar cells was observed. In comparison, the pore size of mesoporous TiO2 first increased greatly before quickly decreasing, and a similar trend was also observed for electrical conductivity. These implied that the interparticle interaction became much stronger with an optimum amount of PEG added to form mesoporous TiO2 NPs. With an optimum molar ratio of PEG/Ti precursor at 0.75, greatly improved conductivity of mesoporous TiO2 NPs with interconnection as compared to that prepared in the absence of PEG, which was used as an electron transport layer, improved the power conversion efficiency of perovskite solar cells by ≈36%. Their greatly reduced photoluminescence after incorporating the perovskite also revealed a difference in the electron‐injection properties from the perovskite into mesoporous TiO2. This strategy highlights a versatile tool to tune mesoporous structures to achieve a cooperative effect for studying photovoltaic properties in perovskite solar cells.
- 26 February 2018
- Published by Wiley in Chemnanomat
- Vol. 4 (4) , 394-400
Fabrication of Mesoporous Titania Nanoparticles with Controlled Porosity and Connectivity for Studying the Photovoltaic Properties in Perovskite Solar Cells
Mesoporous titania (TiO2) nanoparticles (NPs) were synthesized by treating prehydrolyzed titanium precursors with polyethylene glycol (PEG). By varying the amount of PEG, their different physical properties were tuned appropriately in terms of surface area, pore size/volume, and electrical conductivity. By increasing the amount of PEG in TiO2, the surface area and pore volume of mesoporous TiO2 increased, and no direct correlation with the photovoltaic performance of perovskite solar cells was observed. In comparison, the pore size of mesoporous TiO2 first increased greatly before quickly decreasing, and a similar trend was also observed for electrical conductivity. These implied that the interparticle interaction became much stronger with an optimum amount of PEG added to form mesoporous TiO2 NPs. With an optimum molar ratio of PEG/Ti precursor at 0.75, greatly improved conductivity of mesoporous TiO2 NPs with interconnection as compared to that prepared in the absence of PEG, which was used as an electron transport layer, improved the power conversion efficiency of perovskite solar cells by ≈36%. Their greatly reduced photoluminescence after incorporating the perovskite also revealed a difference in the electron‐injection properties from the perovskite into mesoporous TiO2. This strategy highlights a versatile tool to tune mesoporous structures to achieve a cooperative effect for studying photovoltaic properties in perovskite solar cells.