Florival R. Carvalho
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Florival R. Carvalho has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Celmy Maria Bezerra Menezes Barbosa
Department of Chemical Engineering, Federal University of Pernambuco, Recife, PE, Brazil CEP
2 shared publications - Denisson De Oliveira Libório
Universidade Federal de Sergipe
2 shared publications - Jose Geraldo Andrade Pacheco
Federal University of Pernambuco
2 shared publications - Roger Frety
CNRS
2 shared publications - Santiago Arias
Universidade Federal de Pernambuco
2 shared publications - Aline Machado de Castro
Biotechnology Division, Research and Development Center, PETROBRAS, Rio de Janeiro, Brazil
1 shared publication
Latest Publications
- Open Access
Hydrogen-Free Deoxygenation of Oleic Acid and Industrial Vegetable Oil Waste on CuNiAl Catalysts for Biofuel Production
The pyrolysis of vegetable oil waste is an alternative way to convert biomass into high-quality second-generation biofuels, with social, economic and environmental sustainability. The present work deals with the pyrolysis of oleic acid as a model compound and an industrial vegetable oil residue on CuNiAl mixed oxide catalysts, derived from layered double hydroxides. Reactions of the oils pre-adsorbed on the catalysts (catalyst:oil mass ratio of 5:1) were performed at 550 °C on a micro-pyrolysis system and the analyses of volatile products were carried out online using GC/MS. Copper addition to NiAl catalysts increased the cracking of oleic acid. Increasing copper content also decreased the formation of aromatics and coke precursors, as well as oxygenated compounds. The CuNiAl catalyst with a Cu/Ni ratio of 0.4 showed strong catalytic activity in the conversion of an industrial vegetable oil residue with a high volume of free fatty acids produced. Compared to the non-catalytic reaction, the catalyst reduced the content of oxygenates and increased the content of hydrocarbons, particularly in the gasoline range (C5–C9). The CuNiAl oxide catalyst was able to convert vegetable oil residues into hydrocarbons in the range of gasoline, kerosene and diesel, and also linear alkylbenzenes as chemical precursors for surfactant production.
Open AccessHydrogen-Free Deoxygenation of Oleic Acid and Industrial Vegetable Oil Waste on CuNiAl Catalysts for Biofuel Production
The pyrolysis of vegetable oil waste is an alternative way to convert biomass into high-quality second-generation biofuels, with social, economic and environmental sustainability. The present work deals with the pyrolysis of oleic acid as a model compound and an industrial vegetable oil residue on CuNiAl mixed oxide catalysts, derived from layered double hydroxides. Reactions of the oils pre-adsorbed on the catalysts (catalyst:oil mass ratio of 5:1) were performed at 550 °C on a micro-pyrolysis system and the analyses of volatile products were carried out online using GC/MS. Copper addition to NiAl catalysts increased the cracking of oleic acid. Increasing copper content also decreased the formation of aromatics and coke precursors, as well as oxygenated compounds. The CuNiAl catalyst with a Cu/Ni ratio of 0.4 showed strong catalytic activity in the conversion of an industrial vegetable oil residue with a high volume of free fatty acids produced. Compared to the non-catalytic reaction, the catalyst reduced the content of oxygenates and increased the content of hydrocarbons, particularly in the gasoline range (C5–C9). The CuNiAl oxide catalyst was able to convert vegetable oil residues into hydrocarbons in the range of gasoline, kerosene and diesel, and also linear alkylbenzenes as chemical precursors for surfactant production.
- Open Access
Chemical Recycling of PET Using Catalysts from Layered Double Hydroxides: Effect of Synthesis Method and Mg-Fe Biocompatible Metals
The chemical recycling of poly(ethylene terephthalate) (PET) residues was performed via glycolysis with ethylene glycol (EG) over Mg-Fe and Mg-Al oxide catalysts derived from layered double hydroxides. Catalysts prepared using the high supersaturation method (h.s.c.) presented a higher surface area and larger particles, but this represented less PET conversion than those prepared by the low supersaturation method (l.s.c.). This difference was attributed to the smaller mass transfer limitations inside the (l.s.c.) catalysts. An artificial neural network model well fitted the PET conversion and bis(2-hydroxyethyl) terephthalate (BHET) yield. The influence of Fe in place of Al resulted in a higher PET conversion of the Mg-Fe-h.s.c. catalyst (~95.8%) than of Mg-Al-h.s.c. (~63%). Mg-Fe catalysts could be reused four to five times with final conversions of up to 97% with reaction conditions of EG: PET = 5:1 and catalyst: PET = 0.5%. These results confirm the Mg-Fe oxides as a biocompatible novel catalyst for the chemical recycling of PET residues to obtain non-toxic BHET for further polymerization, and use in food and beverage packaging.
Open AccessChemical Recycling of PET Using Catalysts from Layered Double Hydroxides: Effect of Synthesis Method and Mg-Fe Biocompatible Metals
The chemical recycling of poly(ethylene terephthalate) (PET) residues was performed via glycolysis with ethylene glycol (EG) over Mg-Fe and Mg-Al oxide catalysts derived from layered double hydroxides. Catalysts prepared using the high supersaturation method (h.s.c.) presented a higher surface area and larger particles, but this represented less PET conversion than those prepared by the low supersaturation method (l.s.c.). This difference was attributed to the smaller mass transfer limitations inside the (l.s.c.) catalysts. An artificial neural network model well fitted the PET conversion and bis(2-hydroxyethyl) terephthalate (BHET) yield. The influence of Fe in place of Al resulted in a higher PET conversion of the Mg-Fe-h.s.c. catalyst (~95.8%) than of Mg-Al-h.s.c. (~63%). Mg-Fe catalysts could be reused four to five times with final conversions of up to 97% with reaction conditions of EG: PET = 5:1 and catalyst: PET = 0.5%. These results confirm the Mg-Fe oxides as a biocompatible novel catalyst for the chemical recycling of PET residues to obtain non-toxic BHET for further polymerization, and use in food and beverage packaging.
- Open Access
- 1 January 2023
- Published by Editora Cientifica Digital
- Vol. 1, 288-291
HIDROTRATAMENTO DE ÓLEO DE SOJA PARA PRODUÇÃO DE DIESEL VERDE
O diesel renovável, ou diesel verde, é o biocombustível de uso que mais cresce no mundo e o uso em substituição ao diesel fóssil é importante para reduzir o impacto das emissões de carbono. O diesel verde é formado por uma mistura de hidrocarbonetos com composição química semelhante à do combustível fóssil, tornando-o um biocombustível drop-in. O presente trabalho propõe um modelo de hidrotratamento de óleo de soja para a produção de diesel verde. O processo foi simulado em Aspen Plus® v10 e as reações de descarboxilação, descarbonilação e hidrodesoxigenação foram inseridas em um reator estequiométrico na presença do catalisador NiMo/Al2O3. Também foram consideradas reações de craqueamento e fracionamento, e foram produzidos biocombustível de aviação e gases leves, além do diesel verde. O óleo de soja brasileiro foi utilizado como matéria-prima para a produção do diesel verde. A razão hidrogênio/óleo de soja foi de 0,031 e a energia utilizada no processo foi de 1181 kW/h. Mais de 80% do óleo de soja foi convertido em combustíveis renováveis, sendo aproximadamente 65% em diesel verde. Além disso, foi feita uma previsão das propriedades físico-químicas simuladas e comparadas com a legislação brasileira vigente para diesel verde obtendo valores dentro das especificações estabelecidas.
- 1 January 2023
- Published by Editora Cientifica Digital
- Vol. 1, 288-291
Open AccessHIDROTRATAMENTO DE ÓLEO DE SOJA PARA PRODUÇÃO DE DIESEL VERDE
O diesel renovável, ou diesel verde, é o biocombustível de uso que mais cresce no mundo e o uso em substituição ao diesel fóssil é importante para reduzir o impacto das emissões de carbono. O diesel verde é formado por uma mistura de hidrocarbonetos com composição química semelhante à do combustível fóssil, tornando-o um biocombustível drop-in. O presente trabalho propõe um modelo de hidrotratamento de óleo de soja para a produção de diesel verde. O processo foi simulado em Aspen Plus® v10 e as reações de descarboxilação, descarbonilação e hidrodesoxigenação foram inseridas em um reator estequiométrico na presença do catalisador NiMo/Al2O3. Também foram consideradas reações de craqueamento e fracionamento, e foram produzidos biocombustível de aviação e gases leves, além do diesel verde. O óleo de soja brasileiro foi utilizado como matéria-prima para a produção do diesel verde. A razão hidrogênio/óleo de soja foi de 0,031 e a energia utilizada no processo foi de 1181 kW/h. Mais de 80% do óleo de soja foi convertido em combustíveis renováveis, sendo aproximadamente 65% em diesel verde. Além disso, foi feita uma previsão das propriedades físico-químicas simuladas e comparadas com a legislação brasileira vigente para diesel verde obtendo valores dentro das especificações estabelecidas.