Anatoly P. Mukhachev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Anatoly P. Mukhachev has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
D.O. Yelatontsev
Inst Geotech Mech, Dnipro, Ukraine
3 shared publications- Dmytro Yelatontsev
M. S. Poliakov Institute of Geotechnical Mechanics, National Academy of Sciences of Ukraine, 2-a, Simferopolska St., 49005 Dnipro, Ukraine
3 shared publications O.A. Kharytonova
Dnipro State Tech Univ, Kamianske, Ukraine
2 shared publicationsDmytro Yelatontsev
M.S. Poliakov Institute of Geotechnical Mechanics of the National Academy of Sciences of Ukraine, 2a Simferopolska St., 49005 Dnipro, Ukraine
1 shared publicationKateryna Bozhko
Dniprovsk State Technical University, 2a Dniprobudivska St., 51918 Kamianske, Ukraine
1 shared publicationO.A. Kharitonova
Dnipro State Tech Univ, Kamianske, Ukraine
1 shared publication
Latest Publications
- Open Access
Microstructural Refinement and Property Enhancement of Cast ML5 Magnesium Alloy by Ti, Zr, and Hf Microalloying
This study investigates the effect of Ti, Zr, and Hf microalloying on the microstructure, microhardness, tensile properties, and high-temperature performance of cast ML5 magnesium alloy. The alloy was modified with 0.05, 0.10, and 1.0 wt.% Ti, Zr, or Hf, and the resulting alloys were characterized in the as-cast and heat-treated conditions. The effects of microalloying on grain size, secondary dendrite arm spacing, intermetallic phase morphology and volume fraction, matrix microhardness, tensile strength, elongation, and time to failure under prolonged loading at 150 °C and 80 MPa were evaluated. Ti, Zr, and Hf refined the cast structure and reduced the size of the intermetallic constituents. At 0.05–0.10 wt.%, the additions increased the absolute volume fraction of fine spherical intragranular intermetallic particles; however, the relative balance between spherical and plate-like constituents depended on the alloying element and concentration. At 1.0 wt.%, the plate-like fraction increased more strongly. All three elements increased matrix microhardness and tensile strength, but their relative effects were property-dependent: the increase in matrix microhardness ranked Ti < Zr < Hf, whereas the tensile-strength response after heat treatment ranked Ti < Hf < Zr at the investigated concentrations. For all three elements, elongation increased up to 0.10 wt.% and decreased at 1.0 wt.%. After heat treatment, ML5 containing 0.10 wt.% Hf exhibited a tensile strength of 260.0 MPa, an elongation of 4.9%, and a time to failure of 288.3 h at 150 °C and 80 MPa, compared with 231.8 MPa, 2.9%, and 141.4 h, respectively, for the reference alloy. The results provide a controlled comparison of the concentration-dependent effects of Ti, Zr, and Hf on the grain structure, room-temperature properties, and prolonged-loading performance of cast ML5, while the provenance of overlapping and newly obtained values is specified separately.
Open AccessMicrostructural Refinement and Property Enhancement of Cast ML5 Magnesium Alloy by Ti, Zr, and Hf Microalloying
This study investigates the effect of Ti, Zr, and Hf microalloying on the microstructure, microhardness, tensile properties, and high-temperature performance of cast ML5 magnesium alloy. The alloy was modified with 0.05, 0.10, and 1.0 wt.% Ti, Zr, or Hf, and the resulting alloys were characterized in the as-cast and heat-treated conditions. The effects of microalloying on grain size, secondary dendrite arm spacing, intermetallic phase morphology and volume fraction, matrix microhardness, tensile strength, elongation, and time to failure under prolonged loading at 150 °C and 80 MPa were evaluated. Ti, Zr, and Hf refined the cast structure and reduced the size of the intermetallic constituents. At 0.05–0.10 wt.%, the additions increased the absolute volume fraction of fine spherical intragranular intermetallic particles; however, the relative balance between spherical and plate-like constituents depended on the alloying element and concentration. At 1.0 wt.%, the plate-like fraction increased more strongly. All three elements increased matrix microhardness and tensile strength, but their relative effects were property-dependent: the increase in matrix microhardness ranked Ti < Zr < Hf, whereas the tensile-strength response after heat treatment ranked Ti < Hf < Zr at the investigated concentrations. For all three elements, elongation increased up to 0.10 wt.% and decreased at 1.0 wt.%. After heat treatment, ML5 containing 0.10 wt.% Hf exhibited a tensile strength of 260.0 MPa, an elongation of 4.9%, and a time to failure of 288.3 h at 150 °C and 80 MPa, compared with 231.8 MPa, 2.9%, and 141.4 h, respectively, for the reference alloy. The results provide a controlled comparison of the concentration-dependent effects of Ti, Zr, and Hf on the grain structure, room-temperature properties, and prolonged-loading performance of cast ML5, while the provenance of overlapping and newly obtained values is specified separately.
- Open Access
- 20 May 2024
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 526, 01013
Eco-friendly technology for “Nitrofos” fertilizer obtained from radioactive man-made waste
The article presents the results of research into the process of purification of phosphoric acid from radioactive isotopes after extraction of uranium, thorium, and REE. It is shown that the main purification of acid is achieved in the process of gypsum precipitation with sulfuric acid and barium nitrate. Additional purification of nitrate-phosphate solution is achieved after uranium extraction and sorption-extraction purification of REE. The sorption raffinate with a concentration of P2O5 25 g/L, REE 0.5 g/L and NH4NO3 300 g/L were used for fertilizer production. Additional purification of NH4NO3 solution from isotopes 226Ra, 210Po, 227Ac is achieved in the process of REE extraction purification. The aggregate of all refining processes of purification of nitrate-phosphate solution from radioactive isotopes provided NP-fertilizer “Nitrofos”, which meets the quality standards. Extraction of P2O5 from raw materials into NP-fertilizer – 90%; extraction of REE from raw materials into collective chemical concentrate – 95%; direct commercial extraction of REE from raw materials into the product – 85%.
- 20 May 2024
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 526, 01013
Open AccessEco-friendly technology for “Nitrofos” fertilizer obtained from radioactive man-made waste
The article presents the results of research into the process of purification of phosphoric acid from radioactive isotopes after extraction of uranium, thorium, and REE. It is shown that the main purification of acid is achieved in the process of gypsum precipitation with sulfuric acid and barium nitrate. Additional purification of nitrate-phosphate solution is achieved after uranium extraction and sorption-extraction purification of REE. The sorption raffinate with a concentration of P2O5 25 g/L, REE 0.5 g/L and NH4NO3 300 g/L were used for fertilizer production. Additional purification of NH4NO3 solution from isotopes 226Ra, 210Po, 227Ac is achieved in the process of REE extraction purification. The aggregate of all refining processes of purification of nitrate-phosphate solution from radioactive isotopes provided NP-fertilizer “Nitrofos”, which meets the quality standards. Extraction of P2O5 from raw materials into NP-fertilizer – 90%; extraction of REE from raw materials into collective chemical concentrate – 95%; direct commercial extraction of REE from raw materials into the product – 85%.
- 12 October 2023
- Published by Problems of Atomic Science and Technology in Problems of Atomic Science and Technology
- No. 5,p. 103-110
TECHNOLOGICAL BASIS OF THE PROCESS OF ZIRCONIUM AND HAFNIUM SEPARATION
- 12 October 2023
- Published by Problems of Atomic Science and Technology in Problems of Atomic Science and Technology
- No. 5,p. 103-110
TECHNOLOGICAL BASIS OF THE PROCESS OF ZIRCONIUM AND HAFNIUM SEPARATION
- Open Access
Production of Zirconium-Niobium Alloys for Nuclear Reactors Fuel Rods via SHS Process
This article presents the results of studies of the self-propagating high-temperature synthesis (SHS) for obtaining zirconium alloys with niobium by the method of calcium-thermal reduction of nuclear-grade zirconium tetrafluoride in the presence of niobium powder. The optimal heating temperature of the initial charge and the methods of charge mixture with different calcium content were determined. The safety of the SHS process is ensured by the formation of an optimal combustion front of the mixture to remove the released high-pressure gases. A setup for the furnace reduction of zirconium alloys with charge preheating, discharge of molten products into molds of various designs, and control of the time and rate of slag and alloy crystallization has been tested. The required performance of the installation, the degree of transition of zirconium from salt into the alloy, and the purity, structure, and uniformity of the alloy were achieved.
Open AccessProduction of Zirconium-Niobium Alloys for Nuclear Reactors Fuel Rods via SHS Process
This article presents the results of studies of the self-propagating high-temperature synthesis (SHS) for obtaining zirconium alloys with niobium by the method of calcium-thermal reduction of nuclear-grade zirconium tetrafluoride in the presence of niobium powder. The optimal heating temperature of the initial charge and the methods of charge mixture with different calcium content were determined. The safety of the SHS process is ensured by the formation of an optimal combustion front of the mixture to remove the released high-pressure gases. A setup for the furnace reduction of zirconium alloys with charge preheating, discharge of molten products into molds of various designs, and control of the time and rate of slag and alloy crystallization has been tested. The required performance of the installation, the degree of transition of zirconium from salt into the alloy, and the purity, structure, and uniformity of the alloy were achieved.
- 10 June 2022
- Published by Problems of Atomic Science and Technology in Problems of Atomic Science and Technology
- No. 2,p. 62-67
PHYSICAL AND CHEMICAL FOUNDATIONS OF THE TECHNOLOGY FOR OBTAINING URANIUM OXIDES
- 10 June 2022
- Published by Problems of Atomic Science and Technology in Problems of Atomic Science and Technology
- No. 2,p. 62-67
PHYSICAL AND CHEMICAL FOUNDATIONS OF THE TECHNOLOGY FOR OBTAINING URANIUM OXIDES
- 1 January 2020
- Published by Ivanovo State University of Chemistry and Technology in ChemChemTech
- Vol. 63 (11) , 88-95
SYNTHESIS AND PROPERTIES OF ION EXCHANGERS DERIVED FROM NON-WOOD CELLULOSE
A rational scheme for the processing of large-scale agro-industrial waste - walnut shells Juglans Regia L. and apricot kernels Prunus Armeniaca L. was proposed. At first stage, the raw material was delignificated using liquid ammonia to remove hemicelluloses and lignin. Isolated non-wood pulp is chemically modifying to increase sorption and ion exchange properties. For the synthesis of anion exchangers, cellulose was aminated using pyridine or trimethylamine after preliminary treatment consequentially with formalin and C2H5OH in HCl medium. As a result, we obtained high and weakly-basic ion exchangers with nitrogen content of 10.3-11.5% and high exchange capacity towards various classes of inorganic anions. For synthesis of cation exchangers, cellulose was treated with solution consisting of 20% H3PO4, 40% CO(NH2)(2), and 40% H2O. Consequently, we obtained phosphorus-containing high-acidic cation exchangers with exchange capacity towards heavy metal of 5.5-8.6 mmol.cm(-3). Both types of ion exchangers have a high capacity towards uranium: anion exchanger - 4.25 mmol.cm(-3) and cation exchanger - 4.94 mmol.cm(-3), respectively. Average total yield of ion exchangers related to weight of air-dry feedstock was 90%. Synthesized ion exchangers characterized by IR spectroscopy. Presence of amine functional groups -NH 2 in aminated cellulose and phosphate ester groups -OPO(OH)(2) in phosphorylated cellulose was established. Specific surface area and total static exchange capacity of synthesized ion exchangers were established. An environmentally friendly method for the disposal of spent solutions from the synthesis of cation exchangers was proposed. It allows getting a liquid complex fertilizer containing 17% N and 13.9% P2O5. Usage of this fertilizer for grain crops feeding increases plants length by 40-75%, as well as overall biomass increase by 20-30%.
- 1 January 2020
- Published by Ivanovo State University of Chemistry and Technology in ChemChemTech
- Vol. 63 (11) , 88-95
SYNTHESIS AND PROPERTIES OF ION EXCHANGERS DERIVED FROM NON-WOOD CELLULOSE
A rational scheme for the processing of large-scale agro-industrial waste - walnut shells Juglans Regia L. and apricot kernels Prunus Armeniaca L. was proposed. At first stage, the raw material was delignificated using liquid ammonia to remove hemicelluloses and lignin. Isolated non-wood pulp is chemically modifying to increase sorption and ion exchange properties. For the synthesis of anion exchangers, cellulose was aminated using pyridine or trimethylamine after preliminary treatment consequentially with formalin and C2H5OH in HCl medium. As a result, we obtained high and weakly-basic ion exchangers with nitrogen content of 10.3-11.5% and high exchange capacity towards various classes of inorganic anions. For synthesis of cation exchangers, cellulose was treated with solution consisting of 20% H3PO4, 40% CO(NH2)(2), and 40% H2O. Consequently, we obtained phosphorus-containing high-acidic cation exchangers with exchange capacity towards heavy metal of 5.5-8.6 mmol.cm(-3). Both types of ion exchangers have a high capacity towards uranium: anion exchanger - 4.25 mmol.cm(-3) and cation exchanger - 4.94 mmol.cm(-3), respectively. Average total yield of ion exchangers related to weight of air-dry feedstock was 90%. Synthesized ion exchangers characterized by IR spectroscopy. Presence of amine functional groups -NH 2 in aminated cellulose and phosphate ester groups -OPO(OH)(2) in phosphorylated cellulose was established. Specific surface area and total static exchange capacity of synthesized ion exchangers were established. An environmentally friendly method for the disposal of spent solutions from the synthesis of cation exchangers was proposed. It allows getting a liquid complex fertilizer containing 17% N and 13.9% P2O5. Usage of this fertilizer for grain crops feeding increases plants length by 40-75%, as well as overall biomass increase by 20-30%.