Edwin Mancilla-Rico
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Edwin Mancilla-Rico has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Alejandro Alzate Buitrago
Ph.D. Candidate, Dept. of Civil Engineering, Universidad Libre de Colombia, Pereira 660001, Colombia; Ph.D. Candidate, Sustainable Development, Universidad de Manizales, Pereira, Risaralda 660001, Colombia. ORCID:
1 shared publication - Ana Letícia Pilz de Castro
Universidade Federal de Ouro Preto, Brasil
1 shared publication - Carlos Barreira Martinez
Universidade Federal de Itajubá, Brasil
1 shared publication - Cristhian Camilo Amariles-López
Professor, Dept. of Civil Engineering, Universidad Libre de Colombia, Pereira 660001, Colombia. ORCID:
1 shared publication - Cristian Camilo Osorio Gómez
Research Assistant of Engineering and Construction Management Research Group and M.Sc. Student, Dept. of Civil and Environmental Engineering, Universidad de los Andes, Bogotá, Colombia.
1 shared publication - Daniel Aristizábal Torres
Universidad Libre Seccional Pereira
1 shared publication
Latest Publications
- 1 December 2024
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 36 (12)
Physicomechanical Properties of Mortar with Diluted EPS as the Binding Material
- 1 December 2024
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 36 (12)
Physicomechanical Properties of Mortar with Diluted EPS as the Binding Material
- Open Access
- 1 September 2018
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 22 (9) , 591-596
Abrasive effects of sediments on impellers of pumps used for catching raw water
This study presents an analysis of the abrasive effects of sediments from the bed of the Acre River, Brazil, on the wear of three different ferrous materials employed in the manufacture of impellers of centrifuge pumps used to catch raw water. In order to evaluate the abrasive wear and specific wear coefficient (k) as a function of sediment concentration, tests were conducted in samples of SAE 8620 steel, nodular cast iron and gray cast iron by using a rotary-ball abrasion meter. These tests employed abrasive slurry with concentration of 1, 2, 3, 5 and 10 g L-1 of sediments in distilled water. The volume of worn material as a function of the relative velocity of water flow in relation to the impeller blades was mathematically estimated. The experimental results showed that: i) The semi-angular and semi-rounded shapes of the sediments from the Acre River produced evidence of micro-grooving and plastic deformation in the three metallic alloys; ii) SAE 8620 steel showed higher resistance to abrasive wear than samples of gray and nodular cast iron; iii) the increase in the volume of worn material due to increment in sediment concentration and the relative velocity of the mixture (water + sediment) to the rotor pads.
- 1 September 2018
- Published by FapUNIFESP (SciELO) in Revista Brasileira de Engenharia Agrícola E Ambiental
- Vol. 22 (9) , 591-596
Open AccessAbrasive effects of sediments on impellers of pumps used for catching raw water
This study presents an analysis of the abrasive effects of sediments from the bed of the Acre River, Brazil, on the wear of three different ferrous materials employed in the manufacture of impellers of centrifuge pumps used to catch raw water. In order to evaluate the abrasive wear and specific wear coefficient (k) as a function of sediment concentration, tests were conducted in samples of SAE 8620 steel, nodular cast iron and gray cast iron by using a rotary-ball abrasion meter. These tests employed abrasive slurry with concentration of 1, 2, 3, 5 and 10 g L-1 of sediments in distilled water. The volume of worn material as a function of the relative velocity of water flow in relation to the impeller blades was mathematically estimated. The experimental results showed that: i) The semi-angular and semi-rounded shapes of the sediments from the Acre River produced evidence of micro-grooving and plastic deformation in the three metallic alloys; ii) SAE 8620 steel showed higher resistance to abrasive wear than samples of gray and nodular cast iron; iii) the increase in the volume of worn material due to increment in sediment concentration and the relative velocity of the mixture (water + sediment) to the rotor pads.