Lixiong Du
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Lixiong Du has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Dongsheng Brian Ma
The University of Texas at Dallas, Richardson, TX, USA
4 shared publications - Dong Yan
Department of Electrical and Computer Engineering, The University of Texas at Dallas, Richardson, TX, USA
1 shared publication - Firooz Aflatouni
University of Pennsylvania
1 shared publication - Yuanqing Huang
Department of Electrical and Computer Engineering, The University of Texas at Dallas, Richardson, TX, USA
1 shared publication - Zhe Xuan
Intel Corporation, Hillsboro, OR, USA
1 shared publication
Latest Publications
- 2 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (11) , 16718-16727
Design of GaN Switching Power IC With Auto-Phase-Aligned EMI Adaptive Self-Cancellation and BER-Conscious Spread Spectrum Modulation
To address mounting electromagnetic interference (EMI) challenges in electric vehicle autonomous driving applications, this article develops an on-chip EMI adaptive self-cancellation (ASC) technique, which stays effective in varying operation conditions. It incorporates an auto-phase-aligned control mechanism to significantly enhance the effectiveness of the ASC technique. Meanwhile, to improve high-frequency EMI suppression, a spread-spectrum modulation (SSM) technique works harmoniously with the ASC to modulate the switching frequency fSW, adaptive to operation conditions. The maximum spread range ΔfSW of the SSM is actively regulated to strictly limit the bit error rate (BER) in the communication system for safety and security. To validate the effectiveness of this article, a switching power converter IC prototype was implemented on a 180-nm BCD process, with a chip area of 1.3 mm2. The converter is purposely designed using GaN power switches and operating at a nominal fSW of 2.2 MHz, imposing more severe di/dt and dv/dt challenges than classic kilohertz-level silicon counterparts. Experimental results prove that the on-chip ASC technique achieves adaptive ripple self-cancellation in response to 150% input and 200% output dynamic voltage changes from the respective nominal levels. The ASC technique alone achieves a maximum EMI reduction of 9.5 dB. In collaboration with the BER-conscious SSM technique, a total EMI reduction of 16.5 dB is achieved at the nominal fSW, satisfying stringent automotive CISPR 25 Class 5 standard.
- 2 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (11) , 16718-16727
Design of GaN Switching Power IC With Auto-Phase-Aligned EMI Adaptive Self-Cancellation and BER-Conscious Spread Spectrum Modulation
To address mounting electromagnetic interference (EMI) challenges in electric vehicle autonomous driving applications, this article develops an on-chip EMI adaptive self-cancellation (ASC) technique, which stays effective in varying operation conditions. It incorporates an auto-phase-aligned control mechanism to significantly enhance the effectiveness of the ASC technique. Meanwhile, to improve high-frequency EMI suppression, a spread-spectrum modulation (SSM) technique works harmoniously with the ASC to modulate the switching frequency fSW, adaptive to operation conditions. The maximum spread range ΔfSW of the SSM is actively regulated to strictly limit the bit error rate (BER) in the communication system for safety and security. To validate the effectiveness of this article, a switching power converter IC prototype was implemented on a 180-nm BCD process, with a chip area of 1.3 mm2. The converter is purposely designed using GaN power switches and operating at a nominal fSW of 2.2 MHz, imposing more severe di/dt and dv/dt challenges than classic kilohertz-level silicon counterparts. Experimental results prove that the on-chip ASC technique achieves adaptive ripple self-cancellation in response to 150% input and 200% output dynamic voltage changes from the respective nominal levels. The ASC technique alone achieves a maximum EMI reduction of 9.5 dB. In collaboration with the BER-conscious SSM technique, a total EMI reduction of 16.5 dB is achieved at the nominal fSW, satisfying stringent automotive CISPR 25 Class 5 standard.
- 13 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (9) , 11687-11696
On-Chip Concurrent Device Aging Prognosis and Dielectric Failure Detection for GaN Power Devices
Despite their promising figure of merits, as emerging wide bandgap (WBG) devices, gallium nitride (GaN) power devices face significant reliability challenges. This article presents an on-chip condition monitoring (CM) approach addressing these challenges by seamlessly integrating device aging prognosis and dielectric failure detection into a unified circuit platform. Specifically, leveraging the device turn-on transient time (ton) as a reliable aging precursor, we propose a closed-loop ton sensing scheme with self-regulated sampling to enhance precursor readout accuracy while mitigating sensing delays. Furthermore, we improve CM accuracy through junction temperature (TJ) calibration, effectively eliminating temperature-induced effects on precursor measurements. Concurrently, we develop a gate leakage current (IGSS) based sensing scheme for dielectric failure detection, sharing the same circuitry of TJ calibration. Leveraging a proposed reconfigurable tri-mode gate driver, this CM approach minimizes impact on normal system operation. A power IC prototype was implemented on a 180-nm BCD process. Demonstrated on a GaN half-bridge power converter, the proposed CM exhibits the precise detection of both device aging and dielectric failure.
- 13 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (9) , 11687-11696
On-Chip Concurrent Device Aging Prognosis and Dielectric Failure Detection for GaN Power Devices
Despite their promising figure of merits, as emerging wide bandgap (WBG) devices, gallium nitride (GaN) power devices face significant reliability challenges. This article presents an on-chip condition monitoring (CM) approach addressing these challenges by seamlessly integrating device aging prognosis and dielectric failure detection into a unified circuit platform. Specifically, leveraging the device turn-on transient time (ton) as a reliable aging precursor, we propose a closed-loop ton sensing scheme with self-regulated sampling to enhance precursor readout accuracy while mitigating sensing delays. Furthermore, we improve CM accuracy through junction temperature (TJ) calibration, effectively eliminating temperature-induced effects on precursor measurements. Concurrently, we develop a gate leakage current (IGSS) based sensing scheme for dielectric failure detection, sharing the same circuitry of TJ calibration. Leveraging a proposed reconfigurable tri-mode gate driver, this CM approach minimizes impact on normal system operation. A power IC prototype was implemented on a 180-nm BCD process. Demonstrated on a GaN half-bridge power converter, the proposed CM exhibits the precise detection of both device aging and dielectric failure.
- 12 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 73 (9) , 12694-12703
Soft-Switched Isolated Half-Bridge Converter With Phase Balanced Series Capacitor Current Doubler Rectifier for Automotive Battery-to-Load Power Delivery
To meet fast-growing demands for high step-down DC-DC power conversion in automotive applications, this article presents a soft-switched isolated half-bridge (IHB) power converter that achieves direct battery-to-load power conversion with high efficiency and power density. The operation on the primary side facilitates zero-voltage switching (ZVS), reducing switching loss significantly. Additionally, it mitigates voltage ringing effects induced by the transformer leakage inductance to reduce electromagnetic interference (EMI). Furthermore, inspired by the popular double step-down (DSD) converter topology, the proposed IHB converter adopts a series-capacitor current doubler rectifier on the secondary side, achieving phase current balancing and minimizing DC offset in transformer magnetizing current. An experimental prototype of the converter was implemented using PCB planar transformer. Accommodating an input voltage ranging from 24 V to 60 V, it achieves an extreme voltage step-down conversion to 1 V with a peak efficiency of 92.7%. It delivers a maximum load current of 30 A, achieving a box power density of 52 W/in 3 . Compared to the conventional symmetrical IHB converter with the same design specifications, this converter improves power efficiency by 4.5% at a light load of 5 A. It reduces peak EMI by 9 dB at the switching frequency of 500 kHz and by 7.1 dB at the resonant frequency of 16 MHz.
- 12 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 73 (9) , 12694-12703
Soft-Switched Isolated Half-Bridge Converter With Phase Balanced Series Capacitor Current Doubler Rectifier for Automotive Battery-to-Load Power Delivery
To meet fast-growing demands for high step-down DC-DC power conversion in automotive applications, this article presents a soft-switched isolated half-bridge (IHB) power converter that achieves direct battery-to-load power conversion with high efficiency and power density. The operation on the primary side facilitates zero-voltage switching (ZVS), reducing switching loss significantly. Additionally, it mitigates voltage ringing effects induced by the transformer leakage inductance to reduce electromagnetic interference (EMI). Furthermore, inspired by the popular double step-down (DSD) converter topology, the proposed IHB converter adopts a series-capacitor current doubler rectifier on the secondary side, achieving phase current balancing and minimizing DC offset in transformer magnetizing current. An experimental prototype of the converter was implemented using PCB planar transformer. Accommodating an input voltage ranging from 24 V to 60 V, it achieves an extreme voltage step-down conversion to 1 V with a peak efficiency of 92.7%. It delivers a maximum load current of 30 A, achieving a box power density of 52 W/in 3 . Compared to the conventional symmetrical IHB converter with the same design specifications, this converter improves power efficiency by 4.5% at a light load of 5 A. It reduces peak EMI by 9 dB at the switching frequency of 500 kHz and by 7.1 dB at the resonant frequency of 16 MHz.
- 1 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 58 (12) , 3481-3491
On-Chip Condition-Adaptive Δ f 3 EMI Control for Switching Power ICs
With perpetual electrification and highly dynamic operations, modern automotive ICs face unprecedented electromagnetic interference (EMI) challenges. To address such, this article presents a condition-adaptive $\Delta f^{3}$ EMI control for automotive power circuits, which coordinates integral spread-spectrum modulation (SSM) schemes to regulate EMI adaptively in response to drastic condition changes of input voltage $V_{\mathrm{IN}}$ and load current $I_{\mathrm{LOAD}}$ . Specifically, a $\Delta f_{\mathrm{SW,UP/DN}}$ spread control technique steers the $\Delta f_{\mathrm{SW}}$ spread direction according to $V_{\mathrm{IN}}$ , while a $\Delta f_{\mathrm{SW}}$ spread range modulation scheme adjusts the $\Delta f_{\mathrm{SW}}$ range according to $I_{\mathrm{LOAD}}$ . Meanwhile, a $\Delta f_{\mathrm{SW}}$ adaptive multi-rate (MR) SSM scheme prevents spectrum overlap spikes. With the three distinct $\Delta f_{\mathrm{SW}}$ -focused control modules working cohesively, we name the overall EMI control as the $\Delta f^{3}$ EMI control in this work. In addition, to avoid high-energy EMI from entering the audible frequency range, a modulation frequency $f_{M}$ envelope tracking scheme is also developed. Demonstrated in an automotive-use GaN switching power converter, this work was fabricated using a 180-nm HV BCD process. It auto-extends $\Delta f_{\mathrm{SW}}$ from 10% to 32% and reduces EMI by 17.2 dB to counteract $I_{\mathrm{LOAD}}$ elevation from 200 mA to 1 A. Meanwhile, it can down-spread $f_{\mathrm{SW}}$ adaptively by the MR-SSM with a 16.3 dB reduction in response to a $V_{\mathrm{IN}}$ increase from 12 V to 24 V without causing overlap spikes.
- 1 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 58 (12) , 3481-3491
On-Chip Condition-Adaptive Δ f 3 EMI Control for Switching Power ICs
With perpetual electrification and highly dynamic operations, modern automotive ICs face unprecedented electromagnetic interference (EMI) challenges. To address such, this article presents a condition-adaptive $\Delta f^{3}$ EMI control for automotive power circuits, which coordinates integral spread-spectrum modulation (SSM) schemes to regulate EMI adaptively in response to drastic condition changes of input voltage $V_{\mathrm{IN}}$ and load current $I_{\mathrm{LOAD}}$ . Specifically, a $\Delta f_{\mathrm{SW,UP/DN}}$ spread control technique steers the $\Delta f_{\mathrm{SW}}$ spread direction according to $V_{\mathrm{IN}}$ , while a $\Delta f_{\mathrm{SW}}$ spread range modulation scheme adjusts the $\Delta f_{\mathrm{SW}}$ range according to $I_{\mathrm{LOAD}}$ . Meanwhile, a $\Delta f_{\mathrm{SW}}$ adaptive multi-rate (MR) SSM scheme prevents spectrum overlap spikes. With the three distinct $\Delta f_{\mathrm{SW}}$ -focused control modules working cohesively, we name the overall EMI control as the $\Delta f^{3}$ EMI control in this work. In addition, to avoid high-energy EMI from entering the audible frequency range, a modulation frequency $f_{M}$ envelope tracking scheme is also developed. Demonstrated in an automotive-use GaN switching power converter, this work was fabricated using a 180-nm HV BCD process. It auto-extends $\Delta f_{\mathrm{SW}}$ from 10% to 32% and reduces EMI by 17.2 dB to counteract $I_{\mathrm{LOAD}}$ elevation from 200 mA to 1 A. Meanwhile, it can down-spread $f_{\mathrm{SW}}$ adaptively by the MR-SSM with a 16.3 dB reduction in response to a $V_{\mathrm{IN}}$ increase from 12 V to 24 V without causing overlap spikes.
- Open Access
- 3 April 2019
- Published by Optica Publishing Group in Optics Express
- Vol. 27 (8) , 10729-10737
Frequency locking of semiconductor lasers to RF oscillators using hybrid-integrated opto-electronic oscillators with dispersive delay lines
Direct frequency locking of lasers to RF oscillators has many applications such as high resolution optical frequency synthesis, coherent optical communication, spectroscopy, sensing, and imaging. Here we present a hybrid-integrated opto-electronic loop that directly frequency locks a semiconductor laser to an RF synthesized source using an opto-electronic oscillator with a dispersive optical delay line. Cascaded ring filters, operating near the resonance frequency, provide an enhanced chromatic dispersion with a compact footprint. The electronic chip is integrated in the GlobalFoundries 180 nm CMOS SOI technology and the photonic chip is integrated in the IME 180 nm SOI technology. A tracking range of 0.5 GHz is achieved while consuming 33 mW power. The proposed scheme is used to frequency lock a commercially available DFB laser, reducing the laser frequency fluctuations by an order of magnitude compared to the free-running case.
- 3 April 2019
- Published by Optica Publishing Group in Optics Express
- Vol. 27 (8) , 10729-10737
Open AccessFrequency locking of semiconductor lasers to RF oscillators using hybrid-integrated opto-electronic oscillators with dispersive delay lines
Direct frequency locking of lasers to RF oscillators has many applications such as high resolution optical frequency synthesis, coherent optical communication, spectroscopy, sensing, and imaging. Here we present a hybrid-integrated opto-electronic loop that directly frequency locks a semiconductor laser to an RF synthesized source using an opto-electronic oscillator with a dispersive optical delay line. Cascaded ring filters, operating near the resonance frequency, provide an enhanced chromatic dispersion with a compact footprint. The electronic chip is integrated in the GlobalFoundries 180 nm CMOS SOI technology and the photonic chip is integrated in the IME 180 nm SOI technology. A tracking range of 0.5 GHz is achieved while consuming 33 mW power. The proposed scheme is used to frequency lock a commercially available DFB laser, reducing the laser frequency fluctuations by an order of magnitude compared to the free-running case.