Espen Birger Raknes
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Espen Birger Raknes has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Børge Arntsen
NTNU
3 shared publications - Bjarte Foseide
Aker BP ASA, Munkegata 26, 7011 Trondheim, Norway
2 shared publications - Martin Landrø
Acoustics Group, Department of Electronic Systems, Norwegian University of Science and Technology
2 shared publications - Geir Jansson
Aker BP ASA, Munkegata 26, 7011 Trondheim, Norway
1 shared publication - Hefeng Dong
Department of Electronic Systems, Norwegian University of Science and Technology, Trondheim, Norway
1 shared publication Ivan Karpov
Norwegian University of Science and Technology
1 shared publication
Latest Publications
- 1 December 2025
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 158 (6) , 4825-4837
Observations from a fiber-pipeline crossing during active and passive seismic acquisition using distributed acoustic sensing
Distributed acoustic sensing (DAS) with horizontal fibers has recently begun to be utilized for offshore seismic imaging. During a field experiment in the North Sea, using a fiber crossing a gas pipeline, we observed anomalous wave arrivals on a specific range of channels and shot gathers. We analyzed the arrivals and interpret them as shear waves (S-waves) that are generated when the compressional direct waves impinge on the pipeline. The S-waves subsequently propagate through the pipeline and are recorded on the fiber section crossing the pipeline. With an increased usage of the fiber network for seismic acquisition, this P-S converted wave may be observed more often in future acquisitions. Our analysis shows the pipeline acting as a wave guide over several hundred meters for signals generated in the water column. These insights may be useful for DAS-based offshore pipeline monitoring. In addition to the arrivals generated during the active acquisition, we analyzed transient signals occurring at the crossing in the passive data. While their distribution over time correlates with the tides, their generation mechanism remains unclear. No periodic signals that could be attributed to the flow in the pipeline were observed in the vicinity of the crossing.
- 1 December 2025
- Published by Acoustical Society of America (ASA) in The Journal of the Acoustical Society of America
- Vol. 158 (6) , 4825-4837
Observations from a fiber-pipeline crossing during active and passive seismic acquisition using distributed acoustic sensing
Distributed acoustic sensing (DAS) with horizontal fibers has recently begun to be utilized for offshore seismic imaging. During a field experiment in the North Sea, using a fiber crossing a gas pipeline, we observed anomalous wave arrivals on a specific range of channels and shot gathers. We analyzed the arrivals and interpret them as shear waves (S-waves) that are generated when the compressional direct waves impinge on the pipeline. The S-waves subsequently propagate through the pipeline and are recorded on the fiber section crossing the pipeline. With an increased usage of the fiber network for seismic acquisition, this P-S converted wave may be observed more often in future acquisitions. Our analysis shows the pipeline acting as a wave guide over several hundred meters for signals generated in the water column. These insights may be useful for DAS-based offshore pipeline monitoring. In addition to the arrivals generated during the active acquisition, we analyzed transient signals occurring at the crossing in the passive data. While their distribution over time correlates with the tides, their generation mechanism remains unclear. No periodic signals that could be attributed to the flow in the pipeline were observed in the vicinity of the crossing.
- Open Access
- 4 April 2025
- Published by Oxford University Press (OUP) in Geophysical Journal International
- Vol. 241 (3) , 1649-1662
Uncertainty quantification of FWI solutions using sequential local ensemble transform Kalman filter for full waveform data
SUMMARY: Full waveform inversion (FWI) has enjoyed increased attention in the past decade, becoming the state of the art for estimating parameters influencing wave propagation in a medium. However, only a few recent emerging efforts have attempted to tackle the challenge of uncertainty quantification in FWI. In this study, we suggest joining FWI with the Bayesian approach, where we provide a post-processing step with an advantageous starting point defined by the global minimum stemming from a deterministic FWI algorithm. Then, using the local ensemble transform Kalman filter (LETKF), we obtain the uncertainty as a follow-up step to the FWI procedure. Within a probabilistic Bayesian inversion framework, the LETKF uses local seismic data to update sets of variables in the subsurface domain. Seismic data for each shot and receiver in the time-domain is in this way matched with subsurface layers, and assimilated in a sequential manner. The methodology is showcased on a realistic model of the Gullfaks field in the North Sea, where we study effects of various seismic acquisition design set-ups, algorithm and model parameter settings. We investigate how these acquisition designs and parameters influence the uncertainty reduction and bias of the inversion results. We highlight the importance of studying statistical performance metrics to ensure a balance between bias and underestimation of uncertainty.
- 4 April 2025
- Published by Oxford University Press (OUP) in Geophysical Journal International
- Vol. 241 (3) , 1649-1662
Open AccessUncertainty quantification of FWI solutions using sequential local ensemble transform Kalman filter for full waveform data
SUMMARY: Full waveform inversion (FWI) has enjoyed increased attention in the past decade, becoming the state of the art for estimating parameters influencing wave propagation in a medium. However, only a few recent emerging efforts have attempted to tackle the challenge of uncertainty quantification in FWI. In this study, we suggest joining FWI with the Bayesian approach, where we provide a post-processing step with an advantageous starting point defined by the global minimum stemming from a deterministic FWI algorithm. Then, using the local ensemble transform Kalman filter (LETKF), we obtain the uncertainty as a follow-up step to the FWI procedure. Within a probabilistic Bayesian inversion framework, the LETKF uses local seismic data to update sets of variables in the subsurface domain. Seismic data for each shot and receiver in the time-domain is in this way matched with subsurface layers, and assimilated in a sequential manner. The methodology is showcased on a realistic model of the Gullfaks field in the North Sea, where we study effects of various seismic acquisition design set-ups, algorithm and model parameter settings. We investigate how these acquisition designs and parameters influence the uncertainty reduction and bias of the inversion results. We highlight the importance of studying statistical performance metrics to ensure a balance between bias and underestimation of uncertainty.
- 9 January 2025
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 90 (5) , P99-P112
Acquisition and imaging of ocean-bottom fiber-optic distributed acoustic sensing data using a full-shot carpet from a conventional 3D survey
Distributed acoustic sensing (DAS) is a novel and fast developing technology that in recent years has been used for turning seabed fiber-optic cables into densely sampled receiver arrays from which the acquired DAS data is used for seismic imaging of the subsurface. The full understanding on how horizontal fiber-optic cables works for these type of applications is still unknown, and more knowledge is therefore needed in data acquisition and imaging. We describe a controlled-source experiment performed offshore Norway, where we interrogated a fiber-optic cable over an area that has it center approximately 100 km from the location on land where the interrogator was installed. The DAS data is compared with towed-streamer data acquired at the same time using a full 3D shot carpet. Data analysis show that the signal-to-noise ratio decreases with increasing distance from the interrogator. We show that the signal amplitude varies with incidence angle. Furthermore, the data quality is considered good at a distance of approximately 130 km from the interrogator, which demonstrates the potential for acquisition of DAS data for subsurface imaging at long distances. For data imaging, we illustrate the importance of using multiple azimuths in the imaging to obtain a subsurface image with sufficient image quality. We find that with the DAS data, we are able to obtain an image quality of the subsurface that is comparable with the towed-streamer data, in particular for areas located directly underneath the fiber-optic cable.
- 9 January 2025
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 90 (5) , P99-P112
Acquisition and imaging of ocean-bottom fiber-optic distributed acoustic sensing data using a full-shot carpet from a conventional 3D survey
Distributed acoustic sensing (DAS) is a novel and fast developing technology that in recent years has been used for turning seabed fiber-optic cables into densely sampled receiver arrays from which the acquired DAS data is used for seismic imaging of the subsurface. The full understanding on how horizontal fiber-optic cables works for these type of applications is still unknown, and more knowledge is therefore needed in data acquisition and imaging. We describe a controlled-source experiment performed offshore Norway, where we interrogated a fiber-optic cable over an area that has it center approximately 100 km from the location on land where the interrogator was installed. The DAS data is compared with towed-streamer data acquired at the same time using a full 3D shot carpet. Data analysis show that the signal-to-noise ratio decreases with increasing distance from the interrogator. We show that the signal amplitude varies with incidence angle. Furthermore, the data quality is considered good at a distance of approximately 130 km from the interrogator, which demonstrates the potential for acquisition of DAS data for subsurface imaging at long distances. For data imaging, we illustrate the importance of using multiple azimuths in the imaging to obtain a subsurface image with sufficient image quality. We find that with the DAS data, we are able to obtain an image quality of the subsurface that is comparable with the towed-streamer data, in particular for areas located directly underneath the fiber-optic cable.
- 29 August 2023
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 88 (6) , WC221-WC236
New wiggles from old cables: Acquisition, cable, and data aspects
Seismic imaging is essential for detailed characterization and understanding of the subsurface. Traditionally, marine seismic data have been acquired either using towed streamers or ocean-bottom receivers. Distributed acoustic sensing (DAS) is a novel and fast-emerging technology that makes it possible to use fiber-optic cables for acoustic measurements. The technology turns the fiber-optic cable into a densely sampled receiver array. A controlled source experiment comparing DAS and conventional towed streamer data for seismic imaging purposes is described. An existing 130 km telecommunication fiber-optic cable was interrogated to acquire DAS data to analyze the signal at long distances and for subsurface imaging. A seismic source vessel was used to create seismic data along the full cable length, while at the same time acquiring conventional towed streamer data for comparison. In addition, the telecommunication fiber-optic cable was used to acquire passive DAS data. The results show that seismic signals in the telecommunication fiber-optic cable are detectable at distances above 100 km from the source point. Furthermore, comparisons of the DAS data and towed streamer data show that the DAS technology allows for the acquisition of large offset seismic data that are comparable with conventional seismic data. Analysis of the passive DAS data shows that the infragravity waves correlate with the observed weather conditions during the acquisition.
- 29 August 2023
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 88 (6) , WC221-WC236
New wiggles from old cables: Acquisition, cable, and data aspects
Seismic imaging is essential for detailed characterization and understanding of the subsurface. Traditionally, marine seismic data have been acquired either using towed streamers or ocean-bottom receivers. Distributed acoustic sensing (DAS) is a novel and fast-emerging technology that makes it possible to use fiber-optic cables for acoustic measurements. The technology turns the fiber-optic cable into a densely sampled receiver array. A controlled source experiment comparing DAS and conventional towed streamer data for seismic imaging purposes is described. An existing 130 km telecommunication fiber-optic cable was interrogated to acquire DAS data to analyze the signal at long distances and for subsurface imaging. A seismic source vessel was used to create seismic data along the full cable length, while at the same time acquiring conventional towed streamer data for comparison. In addition, the telecommunication fiber-optic cable was used to acquire passive DAS data. The results show that seismic signals in the telecommunication fiber-optic cable are detectable at distances above 100 km from the source point. Furthermore, comparisons of the DAS data and towed streamer data show that the DAS technology allows for the acquisition of large offset seismic data that are comparable with conventional seismic data. Analysis of the passive DAS data shows that the infragravity waves correlate with the observed weather conditions during the acquisition.
- 17 June 2020
- Published by Springer Nature in The Journal of Supercomputing
- Vol. 77 (3) , 2416-2457
Elastodynamic full waveform inversion on GPUs with time-space tiling and wavefield reconstruction
- 17 June 2020
- Published by Springer Nature in The Journal of Supercomputing
- Vol. 77 (3) , 2416-2457
Elastodynamic full waveform inversion on GPUs with time-space tiling and wavefield reconstruction
- 27 August 2018
- Published by Society of Exploration Geophysicists
- Vol. 1, 1359-1363
A new method for constructing the Hessian in elastic full-waveform inversion
We propose a method for constructing the Hessian in Elastic Full Waveform Inversion (EFWI) as a series of Hessian-vector products with model perturbations. The assembled Hessian of both simple and complex synthetic models are studied to draw conclusions regarding spatial resolution and parameter retrieval. The results indicate a strong cross-talk between the different model parameters of a common density-velocity parametrisation in EFWI. Furthermore we are able to comment on the influence of offset by comparing zero- and intermediateoffset results. Presentation Date: Wednesday, October 17, 2018 Start Time: 9:20:00 AM Location: Poster Station 7 Presentation Type: Poster
- 27 August 2018
- Published by Society of Exploration Geophysicists
- Vol. 1, 1359-1363
A new method for constructing the Hessian in elastic full-waveform inversion
We propose a method for constructing the Hessian in Elastic Full Waveform Inversion (EFWI) as a series of Hessian-vector products with model perturbations. The assembled Hessian of both simple and complex synthetic models are studied to draw conclusions regarding spatial resolution and parameter retrieval. The results indicate a strong cross-talk between the different model parameters of a common density-velocity parametrisation in EFWI. Furthermore we are able to comment on the influence of offset by comparing zero- and intermediateoffset results. Presentation Date: Wednesday, October 17, 2018 Start Time: 9:20:00 AM Location: Poster Station 7 Presentation Type: Poster
- 27 August 2018
- Published by Society of Exploration Geophysicists
- Vol. 1, 3928-3932
Using interpolation to insert small-scale inhomogeneities in the acoustic finite-difference scheme
We propose a way to include small-scale inhomogeneities and sharp boundaries in high-order acoustic finite difference schemes. The method is based on representing the inhomogeneities as secondary sources defined on dense auxiliary grids. Interaction of the secondary sources with the finite difference scheme is performed by interpolation. We observe good agreement of the method’s results with precise solutions for simple models in 2D. Presentation Date: Wednesday, October 17, 2018 Start Time: 8:30:00 AM Location: 205A (Anaheim Convention Center) Presentation Type: Oral
- 27 August 2018
- Published by Society of Exploration Geophysicists
- Vol. 1, 3928-3932
Using interpolation to insert small-scale inhomogeneities in the acoustic finite-difference scheme
We propose a way to include small-scale inhomogeneities and sharp boundaries in high-order acoustic finite difference schemes. The method is based on representing the inhomogeneities as secondary sources defined on dense auxiliary grids. Interaction of the secondary sources with the finite difference scheme is performed by interpolation. We observe good agreement of the method’s results with precise solutions for simple models in 2D. Presentation Date: Wednesday, October 17, 2018 Start Time: 8:30:00 AM Location: 205A (Anaheim Convention Center) Presentation Type: Oral