Ewa Ozimina
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Ewa Ozimina has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Dariusz Ozimina
Faculty of Mechatronics and Mechanical Engineering, Kielce University of Technology, Tysiąclecia P.P. 7, 25-314 Kielce, Poland
1 shared publication - Joanna Kowalczyk
Kielce University of Technology, Faculty of Mechatronics and Mechanical Engineering
1 shared publication - Lidia Dąbek
Kielce University of Technology, Kielce, Poland
1 shared publication - Monika Madej
Faculty of Mechatronics and Mechanical Engineering, Kielce University of Technology, al. Tysiaclecia Panstwa Polskiego 7, 25-314 Kielce, Poland
1 shared publication - Stanislaw Plaza
University of Lodz
1 shared publication - Tomasz Kozlowski
Department of Geotechnical and Water Engineering, Kielce University of Technology, 25-314 Kielce, Poland
1 shared publication
Latest Publications
- Open Access
- 1 December 2018
- Published by Elsevier in Desalination and Water Treatment
- Vol. 134, 167-173
Predicting bentonite sorption properties toward selected hydrocarbons based on certain physical properties
- 1 December 2018
- Published by Elsevier in Desalination and Water Treatment
- Vol. 134, 167-173
Open AccessPredicting bentonite sorption properties toward selected hydrocarbons based on certain physical properties
- 16 October 2018
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 70 (9) , 1649-1656
Tool wear in dry turning and wet turning with non-toxic cutting fluid
Purpose: This study aims to determine the properties of a new non-toxic cutting fluid and compared with cutting fluid based on mineral oil. Design/methodology/approach: The tool wear was measured under dry and wet cutting conditions. The non-toxic cutting fluid was compared with cutting fluid based on mineral oil. The experiments were carried out using CTX 310 ECO numerical control lathe. The wear of the cutting tools was measured by means of stereo zoom microscopy (SX80), while the elements were identified through scanning electron microscopy (JSM 7100F). The workpiece surface texture was studied using a Talysurf CCI Lite non-contact 3D profiler. The contact wetting angle was established with a KSV CAM 100 tester. Findings: The non-toxic cutting fluid has reached comparable coefficient of friction with a coolant containing mineral oil. The use of the non-toxic cutting fluid with low foaming tendency resulted in lower wear. Practical implications: Machining processes require that cutting fluids be applied to reduce the tool wear and improve the quality of the workpiece surface. Cutting fluids serve numerous purposes such as they act as coolants and lubricants, remove chips and temporarily prevent corrosion of the product. Originality/value: The investigations discussed in this paper have contributed to the development of non-toxic and environmentally friendly manufacturing because of the use of cutting fluid containing zinc aspartate and its comparison with commonly used cutting fluid.
- 16 October 2018
- Published by Emerald Publishing in Industrial Lubrication and Tribology
- Vol. 70 (9) , 1649-1656
Tool wear in dry turning and wet turning with non-toxic cutting fluid
Purpose: This study aims to determine the properties of a new non-toxic cutting fluid and compared with cutting fluid based on mineral oil. Design/methodology/approach: The tool wear was measured under dry and wet cutting conditions. The non-toxic cutting fluid was compared with cutting fluid based on mineral oil. The experiments were carried out using CTX 310 ECO numerical control lathe. The wear of the cutting tools was measured by means of stereo zoom microscopy (SX80), while the elements were identified through scanning electron microscopy (JSM 7100F). The workpiece surface texture was studied using a Talysurf CCI Lite non-contact 3D profiler. The contact wetting angle was established with a KSV CAM 100 tester. Findings: The non-toxic cutting fluid has reached comparable coefficient of friction with a coolant containing mineral oil. The use of the non-toxic cutting fluid with low foaming tendency resulted in lower wear. Practical implications: Machining processes require that cutting fluids be applied to reduce the tool wear and improve the quality of the workpiece surface. Cutting fluids serve numerous purposes such as they act as coolants and lubricants, remove chips and temporarily prevent corrosion of the product. Originality/value: The investigations discussed in this paper have contributed to the development of non-toxic and environmentally friendly manufacturing because of the use of cutting fluid containing zinc aspartate and its comparison with commonly used cutting fluid.