Juan Carlos Sihotang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Juan Carlos Sihotang has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Maman Kartaman Ajiriyanto
Research Center for Nuclear Material and Radioactive Waste Technology – National Research and Innovation Agency
2 shared publications Siti Aidah
2 shared publicationsYusuf Gigih Wicaksono
2 shared publicationsAgus Jamaludin
1 shared publicationAgus Sumaryanto
1 shared publicationAlfahrozin
1 shared publication
Latest Publications
- Open Access
- 23 September 2026
- Published by Elsevier in SSRN Electronic Journal
Influence of Titanium Addition on Phase Transformations and Microstructure of Heat-Treated Uranium-Molybdenum Alloys for Nuclear Fuel Applications
This study investigates the microstructural evolution and phase transformationsin uranium-molybdenum (U-Mo) alloys with titanium (Ti) additions(1-3 wt%) subjected to heat treatment, utilizing X-ray Diraction (XRD)and Energy Dispersive Spectrum (EDS) analyses. The as-received U-Mo alloywas found to be entirely in the γ - UMo (body-centered cubic) phase.Heat treatment alone induced a partial transformation to the α - UMo (orthorhombic)phase. Crucially, the addition of titanium signicantly acceleratedand promoted the complete transformation from γ-UMo to α-UMo,with the α-UMo phase becoming dominant at 1 wt% Ti and reaching over90 wt% at 3 wt% Ti. Concurrently, the intermetallic U2Mo phase was observedto form with Ti addition, and at 3 wt% Ti, uranium dioxide (UO2) also appeared. Detailed crystallographic analysis revealed subtle changes inlattice parameters of the γ - UMo phase with Ti incorporation, suggestingsolid solution eects. EDS analysis highlighted the presence of signicantoxygen and carbon impurities, which likely contributed to UO2 formation athigher Ti concentrations. These ndings underscore titanium's critical rolein tailoring the microstructure of U-Mo alloys, oering potential for optimizingfuel performance by controlling phase stability and density, but alsoemphasize the importance of impurity control during processing for advancednuclear fuel development.
- 23 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInfluence of Titanium Addition on Phase Transformations and Microstructure of Heat-Treated Uranium-Molybdenum Alloys for Nuclear Fuel Applications
This study investigates the microstructural evolution and phase transformationsin uranium-molybdenum (U-Mo) alloys with titanium (Ti) additions(1-3 wt%) subjected to heat treatment, utilizing X-ray Diraction (XRD)and Energy Dispersive Spectrum (EDS) analyses. The as-received U-Mo alloywas found to be entirely in the γ - UMo (body-centered cubic) phase.Heat treatment alone induced a partial transformation to the α - UMo (orthorhombic)phase. Crucially, the addition of titanium signicantly acceleratedand promoted the complete transformation from γ-UMo to α-UMo,with the α-UMo phase becoming dominant at 1 wt% Ti and reaching over90 wt% at 3 wt% Ti. Concurrently, the intermetallic U2Mo phase was observedto form with Ti addition, and at 3 wt% Ti, uranium dioxide (UO2) also appeared. Detailed crystallographic analysis revealed subtle changes inlattice parameters of the γ - UMo phase with Ti incorporation, suggestingsolid solution eects. EDS analysis highlighted the presence of signicantoxygen and carbon impurities, which likely contributed to UO2 formation athigher Ti concentrations. These ndings underscore titanium's critical rolein tailoring the microstructure of U-Mo alloys, oering potential for optimizingfuel performance by controlling phase stability and density, but alsoemphasize the importance of impurity control during processing for advancednuclear fuel development.
- Open Access
- 1 May 2026
- Published by Elsevier in SSRN Electronic Journal
Cation Exchange Method for 137Cs Radionuclide Source Fabrication from Spent U3Si2–Al Reactor Fuel of RSG-GAS for Radiation Portal Monitoring Systems
137Cs Radionuclide as a radiation source can be applied in portal monitor systems, which play an important role in detecting the movement of radioactive materials. One potential source of 137Cs is spent research reactor fuel of the U3Si2–Al type, which contains strategically valuable fission products. This study aims to develop a methodology for cation exchange and production of a 137Cs radionuclide source from the solution obtained in post-irradiation testing of U3Si2–Al fuel with a density of 4.8 gU/cm3. To determine the 137Cs radionuclide content in U3Si2–Al fuel elements, a separation technique is required to isolate 137Cs from other fission products such as uranium. The separation was carried out using a cation exchange method with modified natural Lampung zeolite, which offers good adsorption efficiency, local availability, and thermal and chemical stability. The homogeneity and activity of the 137Cs–zeolite powder were analyzed using a gamma spectrometer. The 137Cs–zeolite powder was then encapsulated in teflon, and its activity was measured using a dose calibrator. The certified 137Cs radionuclide source was placed in a cylindrical stainless steel container lined with lead (Pb) as shielding. Homogeneity testing at seven sampling positions showed that the 137Cs–zeolite powder samples, each weighing approximately 1.0019 g, had an average specific activity of 2.8932 µCi/g with a standard deviation of 0.0058 and a relative standard deviation (RSD) of 0.1996%. These low SD and RSD values indicate that the activity of the 137Cs–zeolite powder samples is not significantly different from that of 137Cs SRM 4233 from NIST, confirming good homogeneity. The certified activity of the 137Cs radionuclide source in the shielded container was 15.91 ± 0.76 µCi with an uncertainty of 5.0%, and the surface radiation exposure rate was 0.57 µSv/h, meeting safety requirements for occupational environments.
- 1 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCation Exchange Method for 137Cs Radionuclide Source Fabrication from Spent U3Si2–Al Reactor Fuel of RSG-GAS for Radiation Portal Monitoring Systems
137Cs Radionuclide as a radiation source can be applied in portal monitor systems, which play an important role in detecting the movement of radioactive materials. One potential source of 137Cs is spent research reactor fuel of the U3Si2–Al type, which contains strategically valuable fission products. This study aims to develop a methodology for cation exchange and production of a 137Cs radionuclide source from the solution obtained in post-irradiation testing of U3Si2–Al fuel with a density of 4.8 gU/cm3. To determine the 137Cs radionuclide content in U3Si2–Al fuel elements, a separation technique is required to isolate 137Cs from other fission products such as uranium. The separation was carried out using a cation exchange method with modified natural Lampung zeolite, which offers good adsorption efficiency, local availability, and thermal and chemical stability. The homogeneity and activity of the 137Cs–zeolite powder were analyzed using a gamma spectrometer. The 137Cs–zeolite powder was then encapsulated in teflon, and its activity was measured using a dose calibrator. The certified 137Cs radionuclide source was placed in a cylindrical stainless steel container lined with lead (Pb) as shielding. Homogeneity testing at seven sampling positions showed that the 137Cs–zeolite powder samples, each weighing approximately 1.0019 g, had an average specific activity of 2.8932 µCi/g with a standard deviation of 0.0058 and a relative standard deviation (RSD) of 0.1996%. These low SD and RSD values indicate that the activity of the 137Cs–zeolite powder samples is not significantly different from that of 137Cs SRM 4233 from NIST, confirming good homogeneity. The certified activity of the 137Cs radionuclide source in the shielded container was 15.91 ± 0.76 µCi with an uncertainty of 5.0%, and the surface radiation exposure rate was 0.57 µSv/h, meeting safety requirements for occupational environments.
- Open Access
- 2 September 2025
- Published by Elsevier in Journal of the Indian Chemical Society
- Vol. 102 (11)
Chemical kinetics of Rare Earth Element (REE) separation by precipitation method
- 2 September 2025
- Published by Elsevier in Journal of the Indian Chemical Society
- Vol. 102 (11)
Open AccessChemical kinetics of Rare Earth Element (REE) separation by precipitation method
- 23 July 2024
- Published by Taylor & Francis in Nuclear Technology
- Vol. 211 (5) , 953-962
Performance Analysis of U 3 Si 2 -Al Fuel with Density of 2.96 gU/cm 3 and Burnup of 56%
- 23 July 2024
- Published by Taylor & Francis in Nuclear Technology
- Vol. 211 (5) , 953-962
Performance Analysis of U 3 Si 2 -Al Fuel with Density of 2.96 gU/cm 3 and Burnup of 56%
- 27 July 2023
- Published by Taylor & Francis in Nuclear Technology
- Vol. 210 (3) , 379-390
Effect of Nb Addition on Corrosion Resistance of U-6Zr Alloys
- 27 July 2023
- Published by Taylor & Francis in Nuclear Technology
- Vol. 210 (3) , 379-390
Effect of Nb Addition on Corrosion Resistance of U-6Zr Alloys