Jie Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jie Liu has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Quanfang Chen
Southwest Jiaotong University, Chengdu, People’s Republic of China
3 shared publications Youming Luo
Southwest Jiaotong Univ, Sch Elect Engn, Chengdu 611756, Peoples R China
3 shared publicationsYuyao Li
School of Electrical Engineering, Southwest Jiaotong University, Chengdu, China
2 shared publicationsAtazaz Hassan
School of Electrical Engineering, Southwest Jiaotong University, Chengdu, China
1 shared publication- Chong Wang
School of Materials and Energy
1 shared publication - Dong Li
School of Chemical Engineering, The Research Center of Chemical Engineering Applying Technology for Resource of Shaanxi, Northwest University, Xi’an, China
1 shared publication
Latest Publications
- 6 July 2024
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 376
Analytical and experimental study on bilayer membrane-type Capacitive Micromechanical Ultrasonic Transducer
- 6 July 2024
- Published by Elsevier in Sensors and Actuators A: Physical
- Vol. 376
Analytical and experimental study on bilayer membrane-type Capacitive Micromechanical Ultrasonic Transducer
- 10 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (19) , 22248-22255
Fabrication of Capacitive Micromachined Ultrasonic Transducer (CMUT) With PMMA/Graphene Membrane
An experimental study of a capacitive micromachined ultrasonic transducer (CMUT) made from a polymethyl methacrylate (PMMA)/graphene composite membrane is presented. Graphene has superior electrical and mechanical properties that make it desirable for sensing and MEMS applications. The novel aspect of this technique is that it fabricates CMUTs from the PMMA/graphene membrane rather than the more common silicon-based membrane. The PMMA/graphene membrane comprised bilayer graphene and 320 nm of PMMA layer. The CMUT was formed by transferring a PMMA/graphene membrane over SU-8 patterned circular cavities with diameters of 60 μm, and this dry transfer method helped to eliminate problems such as stiction and membrane damage that can occur during the bonding process. After bonding, the Raman spectrum of the PMMA/graphene membrane red-shifts, which indicates tensile strain. The surface resistance of the composite membrane measured by the four-wire probe technique was 724.6 Ω/□. Additionally, the Young’s modulus of the composite membrane was determined to be 2.2 GPa through a single-axis stretching test. The resonant frequency, measured in air, was 1.69 MHz, and the quality factor was estimated to be around 34 at the resonance frequency. Based on resonant frequency measurements of 5 CMUT chips, it was observed that the fabricated devices demonstrated a high level of uniformity.
- 10 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 23 (19) , 22248-22255
Fabrication of Capacitive Micromachined Ultrasonic Transducer (CMUT) With PMMA/Graphene Membrane
An experimental study of a capacitive micromachined ultrasonic transducer (CMUT) made from a polymethyl methacrylate (PMMA)/graphene composite membrane is presented. Graphene has superior electrical and mechanical properties that make it desirable for sensing and MEMS applications. The novel aspect of this technique is that it fabricates CMUTs from the PMMA/graphene membrane rather than the more common silicon-based membrane. The PMMA/graphene membrane comprised bilayer graphene and 320 nm of PMMA layer. The CMUT was formed by transferring a PMMA/graphene membrane over SU-8 patterned circular cavities with diameters of 60 μm, and this dry transfer method helped to eliminate problems such as stiction and membrane damage that can occur during the bonding process. After bonding, the Raman spectrum of the PMMA/graphene membrane red-shifts, which indicates tensile strain. The surface resistance of the composite membrane measured by the four-wire probe technique was 724.6 Ω/□. Additionally, the Young’s modulus of the composite membrane was determined to be 2.2 GPa through a single-axis stretching test. The resonant frequency, measured in air, was 1.69 MHz, and the quality factor was estimated to be around 34 at the resonance frequency. Based on resonant frequency measurements of 5 CMUT chips, it was observed that the fabricated devices demonstrated a high level of uniformity.
- 27 July 2023
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 5 (8) , 4316-4322
Capacitive Micromachined Ultrasonic Transducer (CMUT) Made with SWCNTs/Parylene-C Composite Membranes
- 27 July 2023
- Published by American Chemical Society (ACS) in ACS Applied Electronic Materials
- Vol. 5 (8) , 4316-4322
Capacitive Micromachined Ultrasonic Transducer (CMUT) Made with SWCNTs/Parylene-C Composite Membranes