SASamir Ali Amin

Samir Ali Amin

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Samir Ali Amin has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental and Finite Elements Analysis Study of Warming Effect on Deboned Force for Embedded NiTinol Wire into Linear Low Density Polyethylene

    by Samir Ali Amin, Ali Yasser Hassan

    هذا البحث يقدم دراسة نشوء الانسلاخ لسلك نيتينول مفرد سبيكة ذاكرة الشكل داخل بولي اثيلين خطي منخفض الكثافة مصفوفة مركبة دراسة باستخدام فحص السحب. الهدف من هذا البحث دراسة فحص السحب لتحقق من قوة التداخل لمركب بوليميري في حالتين, مع تنشيط سلك النيتينول وبدون تنشيط . في هذا البحث سيكة ذاكرة الشكل سلك نيتينول قطر 2 مليمتر شكل مستقيم كامل التصليب قد استخدم. الدراسة شملت العملي وتحليل العناصر المحددة واخيرا المقارنة بينهم. يعد فحص السحب فحصاً اساسياً بسبب نتائجه لها علاقة بسلوك المواد المركبة الذكية. فحص السحب قد نفذه بواسطة آلة اختبار الشد العالمي نوع (لاري) , ذو سعة حمل 50 كيلو نيوتن, سرعة الفحص 1 ملم/دقيقة قد استخدمت. نفذت نمذجة العناصرالمحدد بوساطة انسيز الاصدار 15. نتائج فحص السحب اثبتت عند تنشيط سلك النيتينول المغمورداخل مصفوفة المضيف بولي اثيلين خطي منخفض الكثافة, قوة الانسلاخ حوالي 74 نيوتن, لكن في حالة بدون تنشيط حوالي 106 نيوتن. اجهاد قص الانسلاخ في التنشيط حوالي 0.73 ميكا باسكال, لكن بدون تنشيط حوالي 0.99 ميكا باسكال. خلال التنشيط النسبة لاجهاد قص الانسلاخ تقل بي 30.47% و 30.13%, على التوالي. نسبة الخطأ بين النتائج العملية والانسزز 8% في...

  • Open Access

    Experimental Study the Effect of Tool Design on the Mechanical Properties of Bobbin Friction Stir Welded 6061-T6 Aluminum Alloy

    by Samir Ali Amin, Mohannad Yousif Hanna, Alhamza Farooq Mohamed

    اللحام بالخلط الاحتكاكي بأداة تشبه البكرة (bobbin) يكون مختلف عن اللحام المتعارف علية للطريقة نفسها, حيث يتم لحام قطعة العمل من الوجهين الاعلى و الاسفل في للشوط نفسها . يتضمن هذا الأسلوب لحام اللوحين من دون الانصهار. في هذا العمل، تم التحقق من تأثير تصميم الأداة على الخواص الميكانيكية لوصلات اللحام لسبيكة الالمنيوم نوع (6061-T6) و بسمك (6,25 ملم) والملحومة بطريقة اللحام الخلطي الاحتكاكي نوع (bobbin)،و كذلك تحديد أفضل تصميم لأداة اللحام نوع (bobbin). خمسة أشكال مختلفة لوتد أداة اللحام (أسطواني مستقيم مسنن, أسطواني مستقيم ذو 3 أوجه، أسطواني مستقيم ذو 4 أوجه، أسطواني مستقيم مسنن ذو 3 أوجه و أسطواني مستقيم مسنن ذو 4 أوجه) وبأبعاد مختلفة للأداة ( الدبوس و الأكتاف ) استخدمت لأجراء عملية اللحام. أتجاه عملية اللحام كان عموديا على أتجاه الدرفلة لألواح الألمنيوم. اختبارات الشد والانحناء تم اجراؤها لأختيار التصميم الأفضل لأداة اللحام نوع (bobbin) والتي تعطي افضل الخواص الميكانيكية لمنطقة اللحام. الأداة ذات الاسطواني المستقيم ذو 4 أوجه، بقطر للوتد (8 mm) والاكتاف (24 mm) أعطت افضل مقاومة شد (193 ميكا باسكال) وأستطالة (6.1%) مع أقصى قوة انحناء (5.7 كيلو نيوتن) وأفضل كفاءة لحام (65.4%) نسبة...


  • Open Access

    Improvement of Dynamic Buckling Behavior of Intermediate Aluminized Stainless Steel Columns

    by Ahmed Naif Al-Khazraji, Samir Ali Al-Rabii, Hameed Shamkhi Al-Khazaali

    This paper experimentally investigated the dynamic buckling behavior of AISI 303 stainless steel aluminized and as received intermediate columns. Twenty seven specimens without aluminizing (type 1) and 75 specimens with hot-dip aluminizing at different aluminizing conditions of dipping temperature and dipping time (type 2), were tested under dynamic compression loading (compression and torsion), dynamic bending loading (bending and torsion), and under dynamic combined loading (compression, bending, and torsion) by using a rotating buckling test machine. The experimental results werecompared with tangent modulus theory, reduced modulus theory, and Perry Robertson interaction formula. Reduced modulus was formulated to circular cross-section for the specimens of type (1).The experimental results obtained showed an advantageous influence of hot-dip aluminizing treatment on the dynamic buckling behavior of AISI 303 stainless steel intermediate columns. The improvements based on the average value of critical stress were19.4 % for intermediate columns type (2) compared with columns type (1) under dynamic compression loading, 8.7 % for intermediate columns type (2) compared with columns type (1) under dynamic bending loading, and 16.5 % for intermediate columns type (2) compared with columns type (1) under dynamic combined loading.

  • Open Access

    Effect of Electrical Discharge Machining and Shot Blast Peening Parameters on Fatigue Life of AISI D2 Die Steel

    by Ahmed Al-Khazraji, Samir Ali Amin, Saad Mahmood Ali

    The present paper deals with studying the effect of electrical discharge machining (EDM) and shot blast peening parameters on work piece fatigue lives using copper and graphite electrodes. Response surface methodology (RSM) and the design of experiment (DOE) were used to plan and design the experimental work matrices for two EDM groups of experiments using kerosene dielectric alone, while the second was treated by the shot blast peening processes after EDM machining. To verify the experimental results, the analysis of variance (ANOVA) was used to predict the EDM models for high carbon high chromium AISI D2 die steel. The work piece fatigue lives in terms of safety factors after EDM models were developed by FEM using ANSYS 15.0 software. The results appeared that the experimental fatigue safety factors (at 106 cycles) decreased by (11 %) after EDM using copper electrodes compared with as-received material and this value is higher by (3.35 %) when using graphite electrodes. The fatigue strength at the same number of cycles was (0.88) and (0.84) times the fatigue strength of as-received material for copper and graphite electrodes respectively. While fatigue strength and safety factors increased after EDM when increasing shot peening time, at the higher shot peening time is by (19.1 %) when using copper electrodes and by (23.26 %) when using graphite electrodes.


  • Open Access

    Modeling and Optimization the Influence of CO2-MAG Welding Parameters on the Weld Joint Shape Factors

    by Samir Ali Amin Alrabii, Tarek M. A. Ali

    This paper represents an experimentalattempt to predict the influence of CO2-MAG welding variables on the shape factors of the weld joint geometry. Theinput variables were welding arc voltage, wire feeding speed and gas flow rate to investigate their effects on the shape factorsof the weld joint geometry in terms of weld joint dimensions (bead width, reinforcement height, and penetration). Design of experiment with response surface methodology technique was employed to buildmathematical models for shape factors in terms of the input welding variables. Thepredicted models were found quadratic type and statistically checked by ANOVA analysis for adequacy purpose. Also, numerical and graphical optimizations were carried out to determine the optimum values for all responses and input variables. The optimum values of the voltage, wire feeding speed, gas flow rate, WPSF, and WRFF are (20 Volt), (153 cm/min), (10 L/min), (5.222), and (3.970), respectively. And, a good agreement was found between the experimental and predicted results. The weld joint efficiency was found (73%) at the optimum conditions.  

  • Open Access

    Fe Analysis of Residual Stresses Induced by Spot Welding of Stainless Steel Type Aisi 316

    by Ahmed N. Al-Khazraji, Samir A. Al-Rabii, Ali Hussein F. Al-Jelehawy

    Specimens of the as-received stainless steel type 316, according to AISI standard, in form of sheet with 1.5 mm thickness were first spot welded and thenshot peened to obtain the influence of shot peening process on the residual stresses induced by spot welding process. X-Ray Diffraction (XRD) method was used to measure the residual stresses. Also, a finite element method (FEM) was employed by ANSYS software version 11 to achieve the simulations for transient thermal analysis and residual stresses analysis in all cases. In addition, the temperature dependency of materials properties was used to assess its effects on the final residual stress results. A comparison showed a very good agreement between the experimental and the numerical results due to the total elimination of tensile residual stresses and creating the compressive type instead.