I Gusti Agung Putu Raka Agung
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
I Gusti Agung Putu Raka Agung has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Pratolo Rahardjo
Dosen Program Studi Teknik Elektro Fakultas Teknik sebagai alat monitoring kandang kelinci board Universitas Udayana Jln. Jalan Kampus Bukit Jimbaran 80361 Indonesia
3 shared publications - I Gede Hery Putrawan1 shared publication
I Gusti
Jurusan Teknik Elektro Fakultas Teknik Universitas Udayana
1 shared publication- Komang Agus Werdi Darmayasa
Prodi Teknik Elektro Fakultas Teknik alat scoring board Universitas Udayana
1 shared publication Raka Agung
Jurusan Teknik Elektro Fakultas Teknik Universitas Udayana
1 shared publicationWayan Yoga Widiana
Jurusan Teknik Elektro Fakultas Teknik Universitas Udayana
1 shared publication
Latest Publications
- Open Access
- 19 October 2019
- Published by Universitas Udayana in Majalah Ilmiah Teknologi Elektro
- Vol. 19 (1) , 1-10
Sistem Monitoring Tingkat Kekeruhan Air dan Pemberi Pakan Otomatis pada Kolam Budidaya Ikan Koi Berbasis NodeMCU
Nowadays, many Indonesian people working as a fish cultivator. This is because the turnover obtained from the sale of fish, one of which is koi fish is quiet high. To cutivate fish especially koi fish, ultivators will make many pools to cultivate these fish. From the first is spawning pool, tiller fish pool and brood pool. To get good quality cultivation, the pools must always be clean (has a turbidity level of water < 400 NTU). Therefore, a system was created to be able to monitor the water turbidity level and automatic feed in koi fish pool which the purpose is helping koi fish cultivator improve their cultivation quality. The monitoring system of the cultivation pool turbidity level works by reading the turbidity value of the pool using a turbidity sensor (Turbidity Sensor). The reading of the sensor value will be processed by the NodeMCU microcontroller and then activate the drainage pump relay module for which will drain turbid water. On the other hand there is a proximity sensor that will measure the height of the pool water. When the pool water is drained, the proximity sensor will send a signal to the NodeMCU microcontroller to activate the distribution pump relay module, so that it can distribute clean water from the water tank to the pool. Therefore, the cultivation pool’s water always be clean. Meanwhile, automatic feeders work using the RTC (Real Time Clock) module in which the feeding time will be set in this module. Then, the time output from the RTC module will be processed by the NodeMCU microcontroller which then sends a signal to the servo as the drive for the fish feed lever. When it is time for feeding, according to the program provided the fish feed lever will open. Therefore, feeding can be done automatically. Keywords — IoT, monitoring, turbidity, feeder, koi fish, cultivation pools.
- 19 October 2019
- Published by Universitas Udayana in Majalah Ilmiah Teknologi Elektro
- Vol. 19 (1) , 1-10
Open AccessSistem Monitoring Tingkat Kekeruhan Air dan Pemberi Pakan Otomatis pada Kolam Budidaya Ikan Koi Berbasis NodeMCU
Nowadays, many Indonesian people working as a fish cultivator. This is because the turnover obtained from the sale of fish, one of which is koi fish is quiet high. To cutivate fish especially koi fish, ultivators will make many pools to cultivate these fish. From the first is spawning pool, tiller fish pool and brood pool. To get good quality cultivation, the pools must always be clean (has a turbidity level of water < 400 NTU). Therefore, a system was created to be able to monitor the water turbidity level and automatic feed in koi fish pool which the purpose is helping koi fish cultivator improve their cultivation quality. The monitoring system of the cultivation pool turbidity level works by reading the turbidity value of the pool using a turbidity sensor (Turbidity Sensor). The reading of the sensor value will be processed by the NodeMCU microcontroller and then activate the drainage pump relay module for which will drain turbid water. On the other hand there is a proximity sensor that will measure the height of the pool water. When the pool water is drained, the proximity sensor will send a signal to the NodeMCU microcontroller to activate the distribution pump relay module, so that it can distribute clean water from the water tank to the pool. Therefore, the cultivation pool’s water always be clean. Meanwhile, automatic feeders work using the RTC (Real Time Clock) module in which the feeding time will be set in this module. Then, the time output from the RTC module will be processed by the NodeMCU microcontroller which then sends a signal to the servo as the drive for the fish feed lever. When it is time for feeding, according to the program provided the fish feed lever will open. Therefore, feeding can be done automatically. Keywords — IoT, monitoring, turbidity, feeder, koi fish, cultivation pools.
- Open Access
- 1 June 2019
- Published by Universitas Udayana in Jurnal SPEKTRUM
- Vol. 6 (2) , 112-120
RANCANG BANGUN KENDALI OTOMATIS LAMPU DAN PENDINGIN RUANGAN PADA RUANG PERKULIAHAN BERBASIS MIKROKONTROLER ARDUINO NANO
Automatic control technology for energy savings is no stranger to social life. Negligence in turning off lights and air conditioners in class is one example of the waste of electricity that occurs in school and campus institutions. By using the PIR (Passive Infra Red) sensor and LDR (Light Dependent Resistor) on the automatic control system of lights and air conditioners, it is expected to reduce excess electricity consumption. All uses of sensors are connected directly to Arduino Nano as the center of automatic system controllers. Software design uses the basic programming language C Arduino and utilizes the timer library function which functions as a room timer. From the results of the research, this tool can already be used as an automation while saving electricity consumption in the use of electronic devices such as lights and air conditioners.
- 1 June 2019
- Published by Universitas Udayana in Jurnal SPEKTRUM
- Vol. 6 (2) , 112-120
Open AccessRANCANG BANGUN KENDALI OTOMATIS LAMPU DAN PENDINGIN RUANGAN PADA RUANG PERKULIAHAN BERBASIS MIKROKONTROLER ARDUINO NANO
Automatic control technology for energy savings is no stranger to social life. Negligence in turning off lights and air conditioners in class is one example of the waste of electricity that occurs in school and campus institutions. By using the PIR (Passive Infra Red) sensor and LDR (Light Dependent Resistor) on the automatic control system of lights and air conditioners, it is expected to reduce excess electricity consumption. All uses of sensors are connected directly to Arduino Nano as the center of automatic system controllers. Software design uses the basic programming language C Arduino and utilizes the timer library function which functions as a room timer. From the results of the research, this tool can already be used as an automation while saving electricity consumption in the use of electronic devices such as lights and air conditioners.
- Open Access
- 19 December 2018
- Published by Universitas Udayana in Jurnal SPEKTRUM
- Vol. 5 (2) , 278-284
RANCANG BANGUN SCORING BOARD MENGGUNAKAN JOYSTICK BERBASIS ARDUINO YANG DIGUNAKAN PADA LATIH TANDING TAEKWONDO
Taekwondo is one of the martial arts competitions competed in the Olympics. Taekwondo comes from Korea, Tae means "kicking or destroying with legs"; Kwon means "boxing"; and Do means "road" or "art". The taekwondo match is led by a referee and a judge who is responsible for giving scores to athletes who get points. During taekwondo match training, the assessment is still done in a manual way so that electronic score equipment is needed that is portable and easy to operate. Based on this, there is a desire to make electronic score equipment used for taekwondo match training by creating a scoring board using an Arduino-based joystick. The Arduino-based scoring board uses two PS3 sticks that are connected to Arduino wirelessly using Bluetooth and received by the joystick receiver. The display value of this match training will be displayed on the LED Matrix display in the form of numbers / scores. The time and the taekwondo match training round are displayed on the seven segment display and are set at the beginning of the practice match using a blue joystick. When the match time runs out, there will be a sound issued by the buzzer. From the research conducted, it is expected to be able to facilitate assessment when competing in taekwondo training.
- 19 December 2018
- Published by Universitas Udayana in Jurnal SPEKTRUM
- Vol. 5 (2) , 278-284
Open AccessRANCANG BANGUN SCORING BOARD MENGGUNAKAN JOYSTICK BERBASIS ARDUINO YANG DIGUNAKAN PADA LATIH TANDING TAEKWONDO
Taekwondo is one of the martial arts competitions competed in the Olympics. Taekwondo comes from Korea, Tae means "kicking or destroying with legs"; Kwon means "boxing"; and Do means "road" or "art". The taekwondo match is led by a referee and a judge who is responsible for giving scores to athletes who get points. During taekwondo match training, the assessment is still done in a manual way so that electronic score equipment is needed that is portable and easy to operate. Based on this, there is a desire to make electronic score equipment used for taekwondo match training by creating a scoring board using an Arduino-based joystick. The Arduino-based scoring board uses two PS3 sticks that are connected to Arduino wirelessly using Bluetooth and received by the joystick receiver. The display value of this match training will be displayed on the LED Matrix display in the form of numbers / scores. The time and the taekwondo match training round are displayed on the seven segment display and are set at the beginning of the practice match using a blue joystick. When the match time runs out, there will be a sound issued by the buzzer. From the research conducted, it is expected to be able to facilitate assessment when competing in taekwondo training.