Yani Li
Research Subjects
Yani Li has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Zhangming Zhu
Xidian University
7 shared publications - Yintang Yang
Xidian University
5 shared publications - Libo Qian
Xidian University
3 shared publications - Lianxi Liu
Xidian University
2 shared publications Wei Qiang
2 shared publications- Xiudeng Wang
Xidian University
2 shared publications
Latest Publications
- 18 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33 (12) , 3207-3215
A 57.2 nW, 1.3–5 V V IN , –85 dB PSRR, 50 μs Start-Up Time, Bandgap Reference Circuit
This article presents a low-power bandgap reference (BGR) featuring high power supply rejection ratio (PSRR) and fast start-up capability, operating across a wide supply voltage range of 1.3–5 V. A novel prebiased pulse current injection technique is proposed in the start-up circuit, achieving a 1% settling time of $50~\mu $ s and a $25\times $ speed gain during start-up. To enhance supply noise immunity, the proposed BGR employs a preregulated (PR)-based amplifier that effectively decouples the reference voltage from supply voltage fluctuations. Fabricated in a 0.18- $\mu $ m BCD process, the proposed reference occupies an active area of 0.0394 mm2. Under a 5 V supply, the circuit generates a 1.2 V reference voltage while consuming only 48 nA quiescent current. Operating down to a minimum supply voltage of 1.3 V, it maintains a low power consumption of 57.2 nW at room temperature. The reference exhibits an average temperature coefficient (TC) of 5.95 ppm/°C across a wide temperature range ( $- 40~^{\circ }$ C to $125~^{\circ }$ C) and achieves an outstanding line sensitivity (LS) of 0.00308%/V over the 1.3–5 V supply range. Furthermore, the measured PSRR reaches −85 dB at 100 Hz.
- 18 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 33 (12) , 3207-3215
A 57.2 nW, 1.3–5 V V IN , –85 dB PSRR, 50 μs Start-Up Time, Bandgap Reference Circuit
This article presents a low-power bandgap reference (BGR) featuring high power supply rejection ratio (PSRR) and fast start-up capability, operating across a wide supply voltage range of 1.3–5 V. A novel prebiased pulse current injection technique is proposed in the start-up circuit, achieving a 1% settling time of $50~\mu $ s and a $25\times $ speed gain during start-up. To enhance supply noise immunity, the proposed BGR employs a preregulated (PR)-based amplifier that effectively decouples the reference voltage from supply voltage fluctuations. Fabricated in a 0.18- $\mu $ m BCD process, the proposed reference occupies an active area of 0.0394 mm2. Under a 5 V supply, the circuit generates a 1.2 V reference voltage while consuming only 48 nA quiescent current. Operating down to a minimum supply voltage of 1.3 V, it maintains a low power consumption of 57.2 nW at room temperature. The reference exhibits an average temperature coefficient (TC) of 5.95 ppm/°C across a wide temperature range ( $- 40~^{\circ }$ C to $125~^{\circ }$ C) and achieves an outstanding line sensitivity (LS) of 0.00308%/V over the 1.3–5 V supply range. Furthermore, the measured PSRR reaches −85 dB at 100 Hz.
- 12 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (1) , 13-17
A Low Quiescent Current Fast Transient LDO Regulator With Segmented Pass Transistors
This brief proposes a low quiescent current fast transient low-dropout regulator (LDO). The pass field-effect transistor (FET) in the LDO is segmented into three sections to cope with different loads. Under no-load mode, the smallest-sized pass transistor is directly driven by the error amplifier (EA) for low quiescent current. At light- and heavy- load modes, the medium and largest sized pass FETs are respectively switched on by different strength buffers for fast transient response. The proposed LDO is implemented in a$0.18~\mu $ m BCD process with an active area of 0.0875 mm2. The LDO consumes a quiescent current of 25 nA at no-load condition, with an input voltage range of 1.5 V-5.5 V and an output voltage range of 1.2 V-5 V. The measured transient output voltage is 28 mV when load current is switched from 0 mA to 200 mA in 100 ns with$1~\mu $ F load capacitance. The recovery time is about$1~\mu $ s. Compared to reported counterparts, the proposed LDO shows an excellent figure-of-merit (FOM).- 12 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 72 (1) , 13-17
A Low Quiescent Current Fast Transient LDO Regulator With Segmented Pass Transistors
This brief proposes a low quiescent current fast transient low-dropout regulator (LDO). The pass field-effect transistor (FET) in the LDO is segmented into three sections to cope with different loads. Under no-load mode, the smallest-sized pass transistor is directly driven by the error amplifier (EA) for low quiescent current. At light- and heavy- load modes, the medium and largest sized pass FETs are respectively switched on by different strength buffers for fast transient response. The proposed LDO is implemented in a$0.18~\mu $ m BCD process with an active area of 0.0875 mm2. The LDO consumes a quiescent current of 25 nA at no-load condition, with an input voltage range of 1.5 V-5.5 V and an output voltage range of 1.2 V-5 V. The measured transient output voltage is 28 mV when load current is switched from 0 mA to 200 mA in 100 ns with$1~\mu $ F load capacitance. The recovery time is about$1~\mu $ s. Compared to reported counterparts, the proposed LDO shows an excellent figure-of-merit (FOM).- Open Access
- 1 January 2023
- Published by Clausius Scientific Press, Inc. in Advances in Vocational and Technical Education
- Vol. 5 (7) , 56-60
Renewal Ideas and Principles of Non-diploma Continuing Education Resource Library in Shaanxi Universities
Integration and updating the non-diploma continuing education resource library is a key issue at this stage, and it is of great significance to perfect the resource system and improve the quality in Shaanxi. Based on the reference of video teaching websites in colleges and universities, and guided by the new educational concepts such as the construction of a learning-oriented society and lifelong education for all. This paper analyzes the significance of the construction of non-diploma continuing education resource library, to sum up the basic ideas and principles of Shaanxi universities, the aim is to provide a theoretical basis to build a scientifically feasible and adult education resource base.
- 1 January 2023
- Published by Clausius Scientific Press, Inc. in Advances in Vocational and Technical Education
- Vol. 5 (7) , 56-60
Open AccessRenewal Ideas and Principles of Non-diploma Continuing Education Resource Library in Shaanxi Universities
Integration and updating the non-diploma continuing education resource library is a key issue at this stage, and it is of great significance to perfect the resource system and improve the quality in Shaanxi. Based on the reference of video teaching websites in colleges and universities, and guided by the new educational concepts such as the construction of a learning-oriented society and lifelong education for all. This paper analyzes the significance of the construction of non-diploma continuing education resource library, to sum up the basic ideas and principles of Shaanxi universities, the aim is to provide a theoretical basis to build a scientifically feasible and adult education resource base.
- Open Access
- 1 December 2022
- Published by Tsinghua University Press in Polyoxometalates
- Vol. 1 (2) , 9140008
Old molybdenum blue for new application: {Mo 72X 30}/PANI/MWCNTs (X = Fe, V) ternary coaxial cable-like fibers for superior electromagnetic wave absorption
- 1 December 2022
- Published by Tsinghua University Press in Polyoxometalates
- Vol. 1 (2) , 9140008
Open AccessOld molybdenum blue for new application: {Mo 72X 30}/PANI/MWCNTs (X = Fe, V) ternary coaxial cable-like fibers for superior electromagnetic wave absorption
- 22 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 70 (1) , 16-20
A 95% Efficiency Reusable Adaptive Time Control Bidirectional Buck Charge Converter for Wide Input Range Operation
A 95% efficiency reusable adaptive time control bidirectional buck charge converter for wide input range operation is presented in this paper. For keeping the switching frequency stable, a reusable adaptive time generator is proposed to improve the transient response and stability of the system. In the buck charging and reverse boost discharging mode, the circuit adopts adaptive off-time control and on-time control, respectively. In order to ensure that the converter can work over a wide input range in the above two working modes, a maximum voltage selection circuit is used to generate a stable high-voltage output signal as the power supply voltage of the system. The proposed bidirectional converter has been fabricated using 0.18-μm BCD process. Measurement results show that the converter has good output accuracy. The switching frequency is centered at 750kHz with less than 1.5% variation when the input voltage is 4.5-14V in the buck mode and 2.6-4.5V in the boost mode. The maximum conversion efficiency is up to 95%. Its minimum input starting voltage can be as low as 2.6V.
- 22 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 70 (1) , 16-20
A 95% Efficiency Reusable Adaptive Time Control Bidirectional Buck Charge Converter for Wide Input Range Operation
A 95% efficiency reusable adaptive time control bidirectional buck charge converter for wide input range operation is presented in this paper. For keeping the switching frequency stable, a reusable adaptive time generator is proposed to improve the transient response and stability of the system. In the buck charging and reverse boost discharging mode, the circuit adopts adaptive off-time control and on-time control, respectively. In order to ensure that the converter can work over a wide input range in the above two working modes, a maximum voltage selection circuit is used to generate a stable high-voltage output signal as the power supply voltage of the system. The proposed bidirectional converter has been fabricated using 0.18-μm BCD process. Measurement results show that the converter has good output accuracy. The switching frequency is centered at 750kHz with less than 1.5% variation when the input voltage is 4.5-14V in the buck mode and 2.6-4.5V in the boost mode. The maximum conversion efficiency is up to 95%. Its minimum input starting voltage can be as low as 2.6V.
- 3 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 69 (1) , 5-9
A 1V 3.5 μW Bio-AFE With Chopper-Capacitor-Chopper Integrator-Based DSL and Low Power GM-C Filter
This brief presents a low-noise, low-power bio-signal acquisition analog front-end (Bio-AFE). It mainly includes a capacitively coupled chopper-stabilized instrumentation amplifier (CCIA), a programmable gain amplifier (PGA), a low-pass filter (LPF), and a successive approximation analog to digital converter (SAR ADC). A chopper-capacitor-chopper integrator based DC servo loop (C 3 IB-DSL) to suppress the electrode DC offset (EDO) with low noise, low process-voltage–temperature (PVT) sensitivity is proposed. Besides, a low power GM-C filter of which the input linear range is extended via inverse hyperbolic tangent pre-distortion circuit is proposed to filter out the spikes, ripples, and high frequency noise in front end. A capacitive feedback PGA is employed to realize a tunable gain of the front end. And a low power SAR ADC is applied to quantify the acquired bio-signal. The proposed analog front end has been fabricated in a $0.18\boldsymbol{\mu }\text{m}$ CMOS process with an area of 0.57mm 2 , consuming $3.5~\boldsymbol{\mu }\text{A}$ from a 1V supply voltage. It achieves an integral noise from 0.5 to 100 Hz of $1.16\boldsymbol{\mu }\text{V}_{\mathrm{ rms}}$ , ±90mV EDO cancellation range, an ADC effective number of 9.06 bit, and the −59.6 dB total harmonic distortion (THD) of total AFE.
- 3 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 69 (1) , 5-9
A 1V 3.5 μW Bio-AFE With Chopper-Capacitor-Chopper Integrator-Based DSL and Low Power GM-C Filter
This brief presents a low-noise, low-power bio-signal acquisition analog front-end (Bio-AFE). It mainly includes a capacitively coupled chopper-stabilized instrumentation amplifier (CCIA), a programmable gain amplifier (PGA), a low-pass filter (LPF), and a successive approximation analog to digital converter (SAR ADC). A chopper-capacitor-chopper integrator based DC servo loop (C 3 IB-DSL) to suppress the electrode DC offset (EDO) with low noise, low process-voltage–temperature (PVT) sensitivity is proposed. Besides, a low power GM-C filter of which the input linear range is extended via inverse hyperbolic tangent pre-distortion circuit is proposed to filter out the spikes, ripples, and high frequency noise in front end. A capacitive feedback PGA is employed to realize a tunable gain of the front end. And a low power SAR ADC is applied to quantify the acquired bio-signal. The proposed analog front end has been fabricated in a $0.18\boldsymbol{\mu }\text{m}$ CMOS process with an area of 0.57mm 2 , consuming $3.5~\boldsymbol{\mu }\text{A}$ from a 1V supply voltage. It achieves an integral noise from 0.5 to 100 Hz of $1.16\boldsymbol{\mu }\text{V}_{\mathrm{ rms}}$ , ±90mV EDO cancellation range, an ADC effective number of 9.06 bit, and the −59.6 dB total harmonic distortion (THD) of total AFE.
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 67 (7) , 1169-1173
High Input Impedance Low-Noise CMOS Analog Frontend IC for Wearable Electrocardiogram Monitoring
The brief presents a CMOS analog frontend ( AFE ) IC with high input impedance low input-referred noise, which for wearable electrocardiogram monitoring. The IC has three main parts, pseudo-differential chopper-stabilized instrumentation amplifier, switched capacitor filter, and low-power continuous--time ∑Δ modulator. The pseudo-differential structure with chopper stabilization improves the input impedance, input--referred noise and chip area. Notably, we propose a new type of negative capacitor circuit to further boost the input impedance. Furthermore, the auto-zero technique is applied to the ripple reduction loop for suppressing the second harmonic ripple and maintain operation throughout the loop cycle. A dc servo loop suppresses the electrode dc offset. In 0.18 μm CMOS process, the proposed AFE IC occupies an active area of 0.99 mm2, consumes 5.8/46.6 μA from a 1.8 V supply, and achieves an input impedance above 2 GΩ, a CMRR of 102 dB and a PSRR of 72 dB.
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 67 (7) , 1169-1173
High Input Impedance Low-Noise CMOS Analog Frontend IC for Wearable Electrocardiogram Monitoring
The brief presents a CMOS analog frontend ( AFE ) IC with high input impedance low input-referred noise, which for wearable electrocardiogram monitoring. The IC has three main parts, pseudo-differential chopper-stabilized instrumentation amplifier, switched capacitor filter, and low-power continuous--time ∑Δ modulator. The pseudo-differential structure with chopper stabilization improves the input impedance, input--referred noise and chip area. Notably, we propose a new type of negative capacitor circuit to further boost the input impedance. Furthermore, the auto-zero technique is applied to the ripple reduction loop for suppressing the second harmonic ripple and maintain operation throughout the loop cycle. A dc servo loop suppresses the electrode dc offset. In 0.18 μm CMOS process, the proposed AFE IC occupies an active area of 0.99 mm2, consumes 5.8/46.6 μA from a 1.8 V supply, and achieves an input impedance above 2 GΩ, a CMRR of 102 dB and a PSRR of 72 dB.
- Open Access
- 12 October 2018
- Published by MDPI AG in Micromachines
- Vol. 9 (10) , 515
Ultrahigh Frequency Ultrasonic Transducers Design with Low Noise Amplifier Integrated Circuit
This paper describes the design of an ultrahigh frequency ultrasound system combined with tightly focused 500 MHz ultrasonic transducers and high frequency wideband low noise amplifier (LNA) integrated circuit (IC) model design. The ultrasonic transducers are designed using Aluminum nitride (AlN) piezoelectric thin film as the piezoelectric element and using silicon lens for focusing. The fabrication and characterization of silicon lens was presented in detail. Finite element simulation was used for transducer design and evaluation. A custom designed LNA circuit is presented for amplifying the ultrasound echo signal with low noise. A Common-source and Common-gate (CS-CG) combination structure with active feedback is adopted for the LNA design so that high gain and wideband performances can be achieved simultaneously. Noise and distortion cancelation mechanisms are also employed in this work to improve the noise figure (NF) and linearity. Designed by using a 0.35 μm complementary metal oxide semiconductor (CMOS) technology, the simulated power gain of the echo signal wideband amplifier is 22.5 dB at 500 MHz with a capacitance load of 1.0 pF. The simulated NF at 500 MHz is 3.62 dB.
- 12 October 2018
- Published by MDPI AG in Micromachines
- Vol. 9 (10) , 515
Open AccessUltrahigh Frequency Ultrasonic Transducers Design with Low Noise Amplifier Integrated Circuit
This paper describes the design of an ultrahigh frequency ultrasound system combined with tightly focused 500 MHz ultrasonic transducers and high frequency wideband low noise amplifier (LNA) integrated circuit (IC) model design. The ultrasonic transducers are designed using Aluminum nitride (AlN) piezoelectric thin film as the piezoelectric element and using silicon lens for focusing. The fabrication and characterization of silicon lens was presented in detail. Finite element simulation was used for transducer design and evaluation. A custom designed LNA circuit is presented for amplifying the ultrasound echo signal with low noise. A Common-source and Common-gate (CS-CG) combination structure with active feedback is adopted for the LNA design so that high gain and wideband performances can be achieved simultaneously. Noise and distortion cancelation mechanisms are also employed in this work to improve the noise figure (NF) and linearity. Designed by using a 0.35 μm complementary metal oxide semiconductor (CMOS) technology, the simulated power gain of the echo signal wideband amplifier is 22.5 dB at 500 MHz with a capacitance load of 1.0 pF. The simulated NF at 500 MHz is 3.62 dB.
- 1 May 2018
- Published by Elsevier in Microelectronics Journal
- Vol. 75, 128-136
A charge-sharing switching scheme for SAR ADCs in biomedical applications
- 1 May 2018
- Published by Elsevier in Microelectronics Journal
- Vol. 75, 128-136
A charge-sharing switching scheme for SAR ADCs in biomedical applications