AAAlexander Allca-Pekarovic

Alexander Allca-Pekarovic

*This is an algorithmically generated author record based on publicly available information.

Alexander Allca-Pekarovic has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A High-Efficiency Propulsion Motor With Distributed High-Density Winding Technology

    by Daniele Meanti, Davide Parati, Alexander Allca-Pekarovic, Moien Masoumi, Kumar Rajasekhara, Berker Bilgin

    This paper presents the development of an electric motor with the novel Distributed High-Density (DHD) winding technology. The DHD winding technology utilizes round wires instead of bar wires. Unlike conventional round-wire winding technique (shed winding), the wires are orderly positioned in the slots in the DHD winding technology, resulting in high fill factor and high efficiency. The implementation of a stator with the DHD winding is presented which utilizes state-of-the-art coil winding and assembly processes. To compare against existing stator designs, a 100 kW, 800 V, and 15,000 RPM propulsion motor is tested experimentally to validate the performance of the DHD winding technology. The acoustic noise behaviour of the propulsion motor is also characterized experimentally. The motor efficiency with the DHD, hairpin, and shed windings are compared for the same stator geometry using simulation results to demonstrate the performance improvement with the DHD winding technology.


  • Experimental Characterization and Modeling of a YASA P400 Axial Flux PM Traction Machine for Performance Analysis of a Chevy Bolt EV

    by Alexander Allca-Pekarovic, Phillip J. Kollmeyer, Alexander Forsyth, Ali Emadi

    This paper investigates a popular off-the shelf performance traction machine, a yokeless and segmented armature (YASA) axial flux surface permanent magnet machine, model P400HC from YASA Motors. A series of manual measurements and automated dynamometer tests were performed at various conditions. From these tests parameters are determined including friction and windage torque, phase resistance, permanent magnet flux linkage, and inductance. The efficiency, phase current, phase voltage, and power factor of the machine was measured over a wide torque, speed, and dc bus voltage range up to around the maximum ratings given by the manufacturer. A range of d-q current values were tested, showing that the machine is slightly salient since maximum torque is achieved when including a small amount of d-axis current. A Chevrolet Bolt electric vehicle (EV) was modeled with the YASA Motors machine and the stock Bolt EV machine. Over four different vehicle drive cycles, the YASA Motors machine was shown to be considerably more lossy than the Bolt EV machine, thereby achieving 4% to 5% less range. The higher loss of the YASA Motors machine likely has several causes, including higher phase resistance, significant friction, windage, and no-load iron losses, and the fact that Bolt EV machine was heavily optimized for an EV application while the YASA Motors machine was optimized to be a highly power dense more general-purpose machine.


  • Loss Modeling and Testing of 800-V DC Bus IGBT and SiC Traction Inverter Modules

    by Alexander Allca-Pekarovic, Phillip J. Kollmeyer, John Reimers, Parisa Mahvelatishamsabadi, Tissaphern Mirfakhrai, Payam Naghshtabrizi, Ali Emadi

    This paper investigates efficiency gains achieved using an 800 V DC bus and wideband gap silicon carbide (SiC) semiconductors for a light-duty electric vehicle (EV), rather than an insulated-gate bipolar transistor (IGBT) inverter with a 400 V bus as is commonly used for EVs. Analytical inverter loss models with 600 V and 1200 V IGBTs, and 1200 V hybrid SiC and 1200 V All-SiC semiconductors are incorporated into a Chevrolet Bolt EV model and simulated over standard drive cycles. Battery pack voltage variations throughout the drive cycles, as well as variations in junction temperature, resulted in 16 to 27 % increased loss compared to fixed voltage and temperature assumptions. To validate the models, experimental testing was performed on a 1200 V IGBT inverter and a 1200 V SiC inverter both powering 160+ kW rated traction machines. Experimentally measured loss was typically within 100 W of the model, demonstrating its accuracy. Going from a 400 V to an 800 V DC bus with IGBTs, EV range was modeled to increase 1.2 %, while an 800 V bus and all SiC inverter results in a range increase of 5.0%. An empirical loss model fitted to measured inverter data shows the analytical model estimates range within 6 km.