Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Bayazid Bustami has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Optimized Synthesis Strategy of Mxene-Loaded Graphitic Carbon Nitride (g-C3N4) for Enhanced Photocatalytic Degradation of Rhodamine B

    by Bayazid Bustami, Parvej Rahman Alif, Mahfuzur Rahman, Mohaiminul Islam, Alam S. M. Nur

    Developing efficient photocatalysts is essential for sustainable wastewater treatment and tackling global water pollution. Graphitic carbon nitride (g-C3N4) is a promising material because it is active under visible light and chemically stable. However, its practical application is limited by fast recombination of charge carriers and a low surface area. In this study, we report a simple hydrothermal method to synthesize exfoliated porous g-C3N4 (E-PGCN) combined with Ti3C2 MXene to form a heterojunction composite that addresses these issues. Various characterization techniques (FTIR, XRD, XPS, SEM, BET) confirmed that adding MXene improves light absorption, increases surface area (53.7 m2/g for the composite versus 21.4 m2/g for bulk g-C3N4 (BGCN)), and enhances charge separation at the interface. Under UV-visible light irradiation with Rhodamine B (RhB) as the model pollutant, the E-PGCN/Ti3C2 MXene composite containing 3 wt% MXene demonstrated an impressive degradation efficiency of 93.2%. This performance is superior to BGCN (66.6%), E-PGCN (82.5%), and E-PGCN/Ti3C2 MXene-5 wt% composites (81%). This is due to the excess Mxene which caused agglomeration and reduced activity. Scavenger studies identified electron radicals as the dominant reactive species, with optimal activity at pH ~4.5. This enhanced performance, 1.4 times greater than BGCN and 1.13 times higher than E-PGCN, is ascribed to the synergistic interplay between the excellent electrical conductivity of MXene and the porous structural features of E-PGCN. This work highlights the importance of morphological engineering and heterojunction design for advancing metal-free photocatalysts, offering a scalable strategy for sustainable water purification.


  • Open Access

    Optimization of Selective Laser Sintering Three-Dimensional Printing of Thermoplastic Polyurethane Elastomer: A Statistical Approach

    by Mahfuzur Rahman, Kazi Arman Ahmed, Mehrab Karim, Jakir Hassan, Rakesh Roy, Bayazid Bustami, S. M. Nur Alam, Hammad Younes

    This research addresses the challenge of determining the optimal parameters for the selective laser sintering (SLS) process using thermoplastic polyurethane elastomer (TPU) flexa black powder to achieve high-quality SLS parts. This study focuses on two key printing process parameters, namely layer thickness and the laser power ratio, and evaluates their impact on four output responses: density, hardness, modulus of elasticity, and time required to produce the parts. The primary impacts and correlations of the input factors on the output responses are evaluated using response surface methodology (RSM). A particular response optimizer is used to find the optimal settings of input variables. Additionally, the rationality of the model is verified through an analysis of variance (ANOVA). The research identifies the optimal combination of process parameters as follows: a 0.11 mm layer thickness and a 1.00 laser power ratio. The corresponding predicted values of the four responses are 152.63 min, 96.96 Shore-A, 2.09 MPa, and 1.12 g/cm3 for printing time, hardness, modulus of elasticity, and density, respectively. These responses demonstrate a compatibility of 66.70% with the objective function. An experimental validation of the predicted values was conducted and the actual values obtained for printing time, hardness, modulus of elasticity, and density at the predicted input process parameters are 159.837 min, 100 Shore-A, 2.17 MPa, and 1.153 g/cm3, respectively. The errors between the predicted and experimental values for each response (time, hardness, modulus of elasticity, and density) were found to be 4.51%, 3.04%, 3.69%, and 2.69%, respectively. These errors are all below 5%, indicating the adequacy of the model. This study also comprehensively describes the influence of process parameters on the responses, which can be helpful for researchers and industry practitioners in setting process parameters of similar SLS operations.


  • Open Access

    Recent Progress in Electrically Conductive and Thermally Conductive Lubricants: A Critical Review

    by Bayazid Bustami, Mahfuzur Rahman, Mst. Jeba Shazida, Mohaiminul Islam, Mahmudul Hasan Rohan, Shakhawat Hossain, Alam S. M. Nur, Hammad Younes

    Electrically as well as thermally conductive lubricants have drawn considerable attention and are an emerging research topic because they have unique advantages and advanced lubrication performance over traditional lubricants such as corrosion protection and efficient heat dissipation. For instance, some components of electric vehicles (EVs) such as bearings, seals, pads and gears require conductive lubricants to avoid premature failure and electromagnetic interference (EMI) problems due to induced shaft voltages and currents. This review provides a comprehensive overview of the recent developments in conductive lubricants. The review focuses on the important aspects to enhance the thermal and electrical conductivities as well as the tribological behavior (COF, and wear rate) of conductive solid, semisolid, and liquid lubricants. The lubricants that are electrically and thermally conductive with superior tribological performances have been identified through extensive literature review and presented in tabular form. This review summarizes the effect of various additives used to improve the conductive properties of the lubricants, such as polyalphaolefin oil, hydraulic oil, paraffin oil, and mineral oil. Furthermore, the review discusses the lubricating mechanism of conductive solid and liquid lubricants to facilitate a deeper understanding. Finally, the future perspectives and the research directions for conductive lubricants are also addressed.