Hao Liang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hao Liang has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Dipak Patel
Institute for Plasma Research
2 shared publications Matt Rindfleisch
Hyper Tech Res Inc, 539 Ind Mile Rd, Columbus, OH 43228 USA
2 shared publicationsAndrzej Morawski
1 shared publication- Andrzej Morawski
Institute of High Pressure Physics PAS, Sokolowska 29/37, 01-142 Warsaw, Poland
1 shared publication Daniel Gajda
1 shared publication- Guoqing Xia
College of Intelligent Systems Science and Engineering, Harbin Engineering University, Harbin 150001, China
1 shared publication
Latest Publications
- Open Access
- 9 September 2026
- Published by Elsevier in SSRN Electronic Journal
Enhanced Critical Current Transport and Improved Grain Connectivity of in-situ MgB2 Wires Doped with Cu2Se
Cu2Se-doped MgB2/Nb/Cu composite superconducting wires are successfully fabricated using the in-situ Powder-in-Tube (PIT) method. The effects of varying Cu2Se doping levels (0, 5, and 10 wt.%) on the microstructure, phase composition, and superconducting properties of the wires are systematically investigated. Microstructural analysis reveals that Cu2Se completely reacts with Mg during the sintering process to form MgSe and MgCu2. These nanoscale secondary phases are uniformly dispersed within the matrix and work synergistically to bridge intergranular gaps and optimize the superconducting electron transport paths. Furthermore, Cu2Se and its reaction products provide heterogeneous nucleation sites and regulate crystal growth, promoting MgB2 grain nucleation and growth and enhancing core density and grain connectivity. Superconducting performance tests demonstrate that Cu2Se doping significantly improves the critical current (Ic) of the wires under low-temperature and zero-field conditions. Notably, the 5 wt.% Cu2Se-doped sample exhibits the best overall performance, achieving an Ic of 252.1 A at 10 K under zero external field, approximately 2.5 times that of the undoped MgB2 wire. The enhancement is primarily attributed to two factors. First, the synergistic effect of deformation densification from the PIT process and doping-induced microstructural optimization improves the superconducting current transport paths. Second, the significant improvement in intergranular connectivity and core density effectively overcomes the weak-link effect, which substantially increases the current-carrying capacity of the wires.
- 9 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEnhanced Critical Current Transport and Improved Grain Connectivity of in-situ MgB2 Wires Doped with Cu2Se
Cu2Se-doped MgB2/Nb/Cu composite superconducting wires are successfully fabricated using the in-situ Powder-in-Tube (PIT) method. The effects of varying Cu2Se doping levels (0, 5, and 10 wt.%) on the microstructure, phase composition, and superconducting properties of the wires are systematically investigated. Microstructural analysis reveals that Cu2Se completely reacts with Mg during the sintering process to form MgSe and MgCu2. These nanoscale secondary phases are uniformly dispersed within the matrix and work synergistically to bridge intergranular gaps and optimize the superconducting electron transport paths. Furthermore, Cu2Se and its reaction products provide heterogeneous nucleation sites and regulate crystal growth, promoting MgB2 grain nucleation and growth and enhancing core density and grain connectivity. Superconducting performance tests demonstrate that Cu2Se doping significantly improves the critical current (Ic) of the wires under low-temperature and zero-field conditions. Notably, the 5 wt.% Cu2Se-doped sample exhibits the best overall performance, achieving an Ic of 252.1 A at 10 K under zero external field, approximately 2.5 times that of the undoped MgB2 wire. The enhancement is primarily attributed to two factors. First, the synergistic effect of deformation densification from the PIT process and doping-induced microstructural optimization improves the superconducting current transport paths. Second, the significant improvement in intergranular connectivity and core density effectively overcomes the weak-link effect, which substantially increases the current-carrying capacity of the wires.
- Open Access
- 31 October 2023
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 36 (12) , 125011
Superconducting joints of reacted monofilament MgB2 wires sintered by hot uniaxial pressing system
Successful superconducting joints of reacted magnesium diboride (MgB2) monofilament wires are reported in this paper. The absence of a reliable method to develop superconducting joints between reacted MgB2 wires presents a major obstacle to the wider adoption of MgB2 as a material for magnet winding. A hot uniaxial pressing (HUP) system was exploited for sintering purposes since it can facilitate the formation of condensed in situ bulk on the wire filament. The wires were manufactured with an extra thick barrier material to protect the filament from damage during HUP sintering. The sintering temperature and pressure of the HUP system were varied to comprehend the best-performing joint. The performance of joints could be improved by depreciating the pores within the intermediate bulk of the joint. To prove this point, joints were cut to study their morphology. However, due to sintering in pressurised conditions, the reaction of the in situ intermediate bulk was not completed. The x-ray diffraction result detected a significant unreacted magnesium phase in the intermediate bulk. This work obtained joints of reacted MgB2 wires which can be considered for industrial MgB2 magnetic resonance imaging magnets fabrication.
- 31 October 2023
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 36 (12) , 125011
Open AccessSuperconducting joints of reacted monofilament MgB2 wires sintered by hot uniaxial pressing system
Successful superconducting joints of reacted magnesium diboride (MgB2) monofilament wires are reported in this paper. The absence of a reliable method to develop superconducting joints between reacted MgB2 wires presents a major obstacle to the wider adoption of MgB2 as a material for magnet winding. A hot uniaxial pressing (HUP) system was exploited for sintering purposes since it can facilitate the formation of condensed in situ bulk on the wire filament. The wires were manufactured with an extra thick barrier material to protect the filament from damage during HUP sintering. The sintering temperature and pressure of the HUP system were varied to comprehend the best-performing joint. The performance of joints could be improved by depreciating the pores within the intermediate bulk of the joint. To prove this point, joints were cut to study their morphology. However, due to sintering in pressurised conditions, the reaction of the in situ intermediate bulk was not completed. The x-ray diffraction result detected a significant unreacted magnesium phase in the intermediate bulk. This work obtained joints of reacted MgB2 wires which can be considered for industrial MgB2 magnetic resonance imaging magnets fabrication.
- Open Access
- 1 July 2023
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 11 (7) , 2217-2229
Recent progress in MgB2 superconducting joint technology
- 1 July 2023
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 11 (7) , 2217-2229
Open AccessRecent progress in MgB2 superconducting joint technology