Sérgio Gustavo Ferreira Cordeiro
Sérgio Gustavo Ferreira Cordeiro has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Francisco Alex Correia Monteiro
Instituto Tecnológico de Aeronáutica, Brazil
4 shared publications - Guilherme Henrique Teixeira
Institute of Applied Mechanics, Graz Center of Computational Engineering (GCCE), Graz University of Technology, Graz, Austria
2 shared publications - Boyang Chen
Aerospace Structure and Materials, Delft University of Technology, Delft, Netherlands
1 shared publication Carlos Henrique Chama Puga
University of Campinas
1 shared publication- David Leonardo Nascimento de Figueiredo Amorim
Graduate Program in Civil Engineering, Federal University of Alagoas, Maceió, Brazil
1 shared publication - Deborah Cristina Nardi
University of São Paulo
1 shared publication
Latest Publications
- Open Access
- 21 August 2026
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 462
A shell-to-shell cohesive line element for efficient modeling of interfacial cracking in overmolded stiffened panels
- 21 August 2026
- Published by Elsevier in Computer Methods in Applied Mechanics and Engineering
- Vol. 462
Open AccessA shell-to-shell cohesive line element for efficient modeling of interfacial cracking in overmolded stiffened panels
- Open Access
- 6 May 2026
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 189
An independent basis IGBEM applied to Burton–Miller boundary integral equations for exterior acoustic problems
- 6 May 2026
- Published by Elsevier in Engineering Analysis with Boundary Elements
- Vol. 189
Open AccessAn independent basis IGBEM applied to Burton–Miller boundary integral equations for exterior acoustic problems
- 18 February 2025
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 47 (3) , 1-20
A co-rotational finite element with embedded plastic discontinuities consistently accounting for distributed loads
- 18 February 2025
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 47 (3) , 1-20
A co-rotational finite element with embedded plastic discontinuities consistently accounting for distributed loads
- Open Access
- 2 December 2024
- Published by Softaliza Tecnologias LTDA in Ibero-Latin American Congress on Computational Methods in Engineering (CILAMCE)
A co-rotational finite element for nonlinear analysis of hollow section steel frames accounting for local buckling via lumped damage mechanics
To reduce engineering costs, the search for more efficient materials and design concepts leads to slender structures. Consequently, the need for geometrically nonlinear analysis is becoming increasingly important. Besides, the phenomenon of local instability becomes more evident when dealing with structural components with hollow cross-sections composed of slender plates and shells. It is usual to employ elastoplastic shell finite element models for dealing with such problems, which leads to analyses with high computational costs. Therefore, this paper proposes a geometrical nonlinear beam finite element, developed for the nonlinear analysis of hollow section steel frames, accounting for local buckling. The finite element is locally formulated as the traditional linear Euler-Bernoulli beam element. A co-rotational description of motion is then employed to account for large displacements and rotations. The local buckling phenomenon is taken into account by a lumped damage model, which concentrates the effects at inelastic hinges. The inelastic hinge´s yield functions are defined in terms of the co-rotational nodal axial forces and bending moments, as well as in terms of damage variables. The local buckling of the hollow sections is accounted by the adopted damage evolution law. The inelastic rotations are governed by the normality rule and the evolution laws of the internal variables. A predictor-corrector algorithm is employed at element level, whereas the Newton-Raphson method solves the global nonlinear equilibrium equations. To assess the accuracy of the proposed model, the numerical results obtained in this study are compared against available numerical and experimental responses. The numerical results show good accuracy, which corroborates that the proposed model might be used in practical applications.
- 2 December 2024
- Published by Softaliza Tecnologias LTDA in Ibero-Latin American Congress on Computational Methods in Engineering (CILAMCE)
Open AccessA co-rotational finite element for nonlinear analysis of hollow section steel frames accounting for local buckling via lumped damage mechanics
To reduce engineering costs, the search for more efficient materials and design concepts leads to slender structures. Consequently, the need for geometrically nonlinear analysis is becoming increasingly important. Besides, the phenomenon of local instability becomes more evident when dealing with structural components with hollow cross-sections composed of slender plates and shells. It is usual to employ elastoplastic shell finite element models for dealing with such problems, which leads to analyses with high computational costs. Therefore, this paper proposes a geometrical nonlinear beam finite element, developed for the nonlinear analysis of hollow section steel frames, accounting for local buckling. The finite element is locally formulated as the traditional linear Euler-Bernoulli beam element. A co-rotational description of motion is then employed to account for large displacements and rotations. The local buckling phenomenon is taken into account by a lumped damage model, which concentrates the effects at inelastic hinges. The inelastic hinge´s yield functions are defined in terms of the co-rotational nodal axial forces and bending moments, as well as in terms of damage variables. The local buckling of the hollow sections is accounted by the adopted damage evolution law. The inelastic rotations are governed by the normality rule and the evolution laws of the internal variables. A predictor-corrector algorithm is employed at element level, whereas the Newton-Raphson method solves the global nonlinear equilibrium equations. To assess the accuracy of the proposed model, the numerical results obtained in this study are compared against available numerical and experimental responses. The numerical results show good accuracy, which corroborates that the proposed model might be used in practical applications.
- Open Access
- 2 December 2024
- Published by Softaliza Tecnologias LTDA in Ibero-Latin American Congress on Computational Methods in Engineering (CILAMCE)
Airfoil lift finite element computations using H1 (Ω) and H(div,Ω) approximation spaces
Computing the lift generated by an airfoil is crucial in aircraft design, especially for aircraft performance prediction, aircraft stability/control, and optimization of airfoil shape for improving efficiency. The problem of incompressible flow around an airfoil is studied herein as a weakly irrotational flow, resulting a div-curl problem in a 2D double-connected domain. The original div-curl problem is ill-posed because it is defined over a multiply-connected domain. Traditionally, a cut in the original domain and additional constrain for the velocity potential and velocity potential gradient at the cut are required for the numerical solution, which applies a rotational correction method based on Helmholtz decomposition of vector fields. The lift coefficient can be finally computed from the numerical solution of the problem. In the present work, the lift of an airfoil is computed from finite element solutions using different approximation spaces: The conventional H1 (Ω) potential-field space and a special class of H(div,Ω) velocity-field space, i.e., the divergence-free space. Accurate analysis using both approximations is performed with h-refinement strategies. The lift coefficient computed from the analysis is compared against available reference solutions. The computational performance and accuracy of the lift computation using the two different approaches are discussed. Finally, the difference in the velocity solution obtained using H1 (Ω) and H(div,Ω) spaces is presented, which can be interpreted as a new posteriori error estimator for the problem.
- 2 December 2024
- Published by Softaliza Tecnologias LTDA in Ibero-Latin American Congress on Computational Methods in Engineering (CILAMCE)
Open AccessAirfoil lift finite element computations using H1 (Ω) and H(div,Ω) approximation spaces
Computing the lift generated by an airfoil is crucial in aircraft design, especially for aircraft performance prediction, aircraft stability/control, and optimization of airfoil shape for improving efficiency. The problem of incompressible flow around an airfoil is studied herein as a weakly irrotational flow, resulting a div-curl problem in a 2D double-connected domain. The original div-curl problem is ill-posed because it is defined over a multiply-connected domain. Traditionally, a cut in the original domain and additional constrain for the velocity potential and velocity potential gradient at the cut are required for the numerical solution, which applies a rotational correction method based on Helmholtz decomposition of vector fields. The lift coefficient can be finally computed from the numerical solution of the problem. In the present work, the lift of an airfoil is computed from finite element solutions using different approximation spaces: The conventional H1 (Ω) potential-field space and a special class of H(div,Ω) velocity-field space, i.e., the divergence-free space. Accurate analysis using both approximations is performed with h-refinement strategies. The lift coefficient computed from the analysis is compared against available reference solutions. The computational performance and accuracy of the lift computation using the two different approaches are discussed. Finally, the difference in the velocity solution obtained using H1 (Ω) and H(div,Ω) spaces is presented, which can be interpreted as a new posteriori error estimator for the problem.
- 17 August 2023
- Published by Wiley in Structural Concrete
- Vol. 25 (1) , 440-455
New damage evolution law in plastic damage models for fiber‐reinforced cementitious composites
Nowadays, fiber‐reinforced cement‐based composites (FRCC) can develop ductile behavior with high toughness when the matrix, fibers, and interface are optimally designed. These materials are promising solutions for constructing more resilient structures. In this context, the widespread use in large‐scale applications requires reliable models to predict the performance of FRCC structures. Usually, the studies on numerical modeling of FRCC apply the damage laws developed for quasi‐brittle concrete, making damage increase faster than really occurs in the presence of fibers. Therefore, the present paper proposes a new damage evolution model for FRCC based on energy dissipation concepts. It is assumed that the dissipated energy contributes fully to the evolution of the scalar damage and plastic strain variables, which is a technical advance from the previous works. The damage evolution is obtained with experimental envelopes of uniaxial stress–strain tests and the focal point from loading–unloading cycles. The results showed that the model accurately predicted experimental results using the damage‐plasticity framework. Furthermore, there are no empirical constants in the proposal, which means that it can be applied to any class of FRCC. An application regarding damage evaluation near a load transfer device in jointed plain cementitious pavements is presented. The damage distribution reveals that using FRCC materials has induced smaller damage values when compared with using conventional concrete. Consequently, cracking is reduced in such zones, increasing the structural life of the pavement.
- 17 August 2023
- Published by Wiley in Structural Concrete
- Vol. 25 (1) , 440-455
New damage evolution law in plastic damage models for fiber‐reinforced cementitious composites
Nowadays, fiber‐reinforced cement‐based composites (FRCC) can develop ductile behavior with high toughness when the matrix, fibers, and interface are optimally designed. These materials are promising solutions for constructing more resilient structures. In this context, the widespread use in large‐scale applications requires reliable models to predict the performance of FRCC structures. Usually, the studies on numerical modeling of FRCC apply the damage laws developed for quasi‐brittle concrete, making damage increase faster than really occurs in the presence of fibers. Therefore, the present paper proposes a new damage evolution model for FRCC based on energy dissipation concepts. It is assumed that the dissipated energy contributes fully to the evolution of the scalar damage and plastic strain variables, which is a technical advance from the previous works. The damage evolution is obtained with experimental envelopes of uniaxial stress–strain tests and the focal point from loading–unloading cycles. The results showed that the model accurately predicted experimental results using the damage‐plasticity framework. Furthermore, there are no empirical constants in the proposal, which means that it can be applied to any class of FRCC. An application regarding damage evaluation near a load transfer device in jointed plain cementitious pavements is presented. The damage distribution reveals that using FRCC materials has induced smaller damage values when compared with using conventional concrete. Consequently, cracking is reduced in such zones, increasing the structural life of the pavement.
- Open Access
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 20 (6) , e499
Numerical investigations in non-watertight models based on a surface-independent discretization boundary element method
It is well known that boundary integral equations are exact mathematical representations of the governing differential equations of a boundary value problem when the integrals are written over a closed-shape boundary representation (B-representation) of the domain, usually reffered to as a watertight B-representation. However, practical geometric design technics (namely, NURBS surfaces) often do not render a watertight B-representation. Non-watertight geometric models with small gaps and overlaps are often generated in the design stage of projects. Based on a proposed surface-independent discretization approach, the present study investigates how unsought gaps affect the response of boundary element models of linear elasticity problems. The developed surface-independent discretization is applied to discretize multiple-patches NURBS B-representation geometries. Linear triangular and quadrilateral elements are adopted to discretize the independent surfaces. Generalized discontinuous elements at the edges of the visible areas of the NURBS parametric spaces are detected by a Level Set function. An offset collocation strategy is adopted for the nodes at the edges of the visible part of the parametric spaces. Thus, singularities and near singularities due to collocation are avoided in the BEM equations. The influence of gaps in the convergence of the L2-norm of boundary displacement error is verified in a 3D example with an available analytical solution. A second example with available numerical solution is analyzed with a non-watertight BEM discretization for qualitative boundary field validation. Finally, a non-watertight B-representation geometry of a crane hook is analyzed. The obtained results have pointed out that, as long as the gaps (and overlaps) are small enough, BEM models built up from non-watertight geometries may produce valuable solutions for practical purposes.
- 1 January 2023
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 20 (6) , e499
Open AccessNumerical investigations in non-watertight models based on a surface-independent discretization boundary element method
It is well known that boundary integral equations are exact mathematical representations of the governing differential equations of a boundary value problem when the integrals are written over a closed-shape boundary representation (B-representation) of the domain, usually reffered to as a watertight B-representation. However, practical geometric design technics (namely, NURBS surfaces) often do not render a watertight B-representation. Non-watertight geometric models with small gaps and overlaps are often generated in the design stage of projects. Based on a proposed surface-independent discretization approach, the present study investigates how unsought gaps affect the response of boundary element models of linear elasticity problems. The developed surface-independent discretization is applied to discretize multiple-patches NURBS B-representation geometries. Linear triangular and quadrilateral elements are adopted to discretize the independent surfaces. Generalized discontinuous elements at the edges of the visible areas of the NURBS parametric spaces are detected by a Level Set function. An offset collocation strategy is adopted for the nodes at the edges of the visible part of the parametric spaces. Thus, singularities and near singularities due to collocation are avoided in the BEM equations. The influence of gaps in the convergence of the L2-norm of boundary displacement error is verified in a 3D example with an available analytical solution. A second example with available numerical solution is analyzed with a non-watertight BEM discretization for qualitative boundary field validation. Finally, a non-watertight B-representation geometry of a crane hook is analyzed. The obtained results have pointed out that, as long as the gaps (and overlaps) are small enough, BEM models built up from non-watertight geometries may produce valuable solutions for practical purposes.
- Open Access
- 1 January 2020
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 17 (8)
The stress intensity factor assessment in three-dimensional problems by the displacement fitting technique and the dual Boundary Element Method
This work presents an extension of the displacement fitting technique for the assessment of stress intensity factors (SIFs) of three-dimensional linear elastic fracture problems using the dual Boundary Element Method. The developed framework accounts for higher-order terms of the asymptotic displacement solution near crack front. The number and location of points surrounding the crack front are properly defined in order to accurately evaluate the SIFs. Three-dimensional benchmarks demonstrate the efficiency of the proposed framework. Moreover, two different fracture criteria illustrate the influence of SIFs values with respect to the crack propagation angle and equivalent factors calculations. The proposed higher-order technique has demonstrated superior performance in comparison with the conventional displacement fitting technique.
- 1 January 2020
- Published by FapUNIFESP (SciELO) in Latin American Journal of Solids and Structures
- Vol. 17 (8)
Open AccessThe stress intensity factor assessment in three-dimensional problems by the displacement fitting technique and the dual Boundary Element Method
This work presents an extension of the displacement fitting technique for the assessment of stress intensity factors (SIFs) of three-dimensional linear elastic fracture problems using the dual Boundary Element Method. The developed framework accounts for higher-order terms of the asymptotic displacement solution near crack front. The number and location of points surrounding the crack front are properly defined in order to accurately evaluate the SIFs. Three-dimensional benchmarks demonstrate the efficiency of the proposed framework. Moreover, two different fracture criteria illustrate the influence of SIFs values with respect to the crack propagation angle and equivalent factors calculations. The proposed higher-order technique has demonstrated superior performance in comparison with the conventional displacement fitting technique.