Sergiy Buhaievskyi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Sergiy Buhaievskyi has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Tetiana Nenastina
Харківський національний автомобільно-дорожній університет
3 shared publications - Igor Shumakov
O.M. Beketov National University of Urban Economy in Kharkiv, Kharkiv
2 shared publications - K. V. Berezhna
Kharkiv National Automobile and Highway University, Kharkiv Ukraine
2 shared publications - Mykola D. Sakhnenko
National technical university «Kharkiv polytechnic institute
2 shared publications - Yuliia Buhaievska
Харківський національний автомобільно-дорожній університет
2 shared publications Armen Atynian
1 shared publication
Latest Publications
- Open Access
- 24 March 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Finite element analysis with experimental verification of concrete anisotropic structures for industrial design under hydrostatic pressure
- 24 March 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Open AccessFinite element analysis with experimental verification of concrete anisotropic structures for industrial design under hydrostatic pressure
- Open Access
- 1 August 2025
- Published by Building Production, State Enterprise 'V.Balytskyi Scientific Research Institute of Building Production (SE 'NDIBV') in Building production
- No. 79,p. 14-21
OPTIMIZATION OF CONSTRUCTIVE AND ORGANIZATIONAL AND TECHNOLOGICAL PARAMETERS OF BRIDGE STRUCTURE RENOVATION
The results of the study on the optimization of structural and technological solutions in the restoration of bridge structures are presented. Reinforced concrete structures damaged by corrosion of concrete and reinforcement, delamination, leaching and concrete soaking are partially replaced and strengthened. The proposed design of a monolithic overlay slab allows for the reinforcement of the prefabricated span structure and the removal of intermediate expansion joints, which are a weak point of the bridge deck. The solution to arrange cavities in the slab is rational, which reduces the material consumption of the technological process. The effectiveness is confirmed by data from the comparison of bending moments from constant loads in the extreme beams of slab span structures. A number of criteria have been identified by which the feasibility of performing an overlay slab can be assessed. For spans of more than 18 m, additional forces in the span structure from the own weight of the overlay slab and sidewalks (especially in the extreme beams for the beam structure) significantly reduce the reinforcement effect (the larger the span, the less effective). In continuous span structures, there is no need to remove intermediate expansion joints (they are absent). In continuous span structures, the maximum tensile forces arise in the supporting sections, in which the overlay slab is made; this leads to a significant change in the structural scheme of the spans and, as a result, significantly higher costs for reinforcing the span structure. With the advent of modern waterproofing systems (epoxy compositions, methyl acrylate compounds, etc.), which have a significantly longer service life and reliability compared to bitumen waterproofing systems, the effect of blocking water access from the bridge deck to the lower structures by the body of the monolithic overlay slab has lost its relevance.
- 1 August 2025
- Published by Building Production, State Enterprise 'V.Balytskyi Scientific Research Institute of Building Production (SE 'NDIBV') in Building production
- No. 79,p. 14-21
Open AccessOPTIMIZATION OF CONSTRUCTIVE AND ORGANIZATIONAL AND TECHNOLOGICAL PARAMETERS OF BRIDGE STRUCTURE RENOVATION
The results of the study on the optimization of structural and technological solutions in the restoration of bridge structures are presented. Reinforced concrete structures damaged by corrosion of concrete and reinforcement, delamination, leaching and concrete soaking are partially replaced and strengthened. The proposed design of a monolithic overlay slab allows for the reinforcement of the prefabricated span structure and the removal of intermediate expansion joints, which are a weak point of the bridge deck. The solution to arrange cavities in the slab is rational, which reduces the material consumption of the technological process. The effectiveness is confirmed by data from the comparison of bending moments from constant loads in the extreme beams of slab span structures. A number of criteria have been identified by which the feasibility of performing an overlay slab can be assessed. For spans of more than 18 m, additional forces in the span structure from the own weight of the overlay slab and sidewalks (especially in the extreme beams for the beam structure) significantly reduce the reinforcement effect (the larger the span, the less effective). In continuous span structures, there is no need to remove intermediate expansion joints (they are absent). In continuous span structures, the maximum tensile forces arise in the supporting sections, in which the overlay slab is made; this leads to a significant change in the structural scheme of the spans and, as a result, significantly higher costs for reinforcing the span structure. With the advent of modern waterproofing systems (epoxy compositions, methyl acrylate compounds, etc.), which have a significantly longer service life and reliability compared to bitumen waterproofing systems, the effect of blocking water access from the bridge deck to the lower structures by the body of the monolithic overlay slab has lost its relevance.
- Open Access
- 1 January 2025
- Published by Publishing House Helvetica (Publications) in Theory and practice of design
- No. 36,p. 313-319
USING AUTODESK INVENTOR PARAMETRIC MODELING IN GLASS SURFACES DESIGN
The article considers the options for using block glazing in interior decoration and provides a brief historical overview of the popularization of this type of glazing both from the point of view of functional properties and from the point of view of aesthetic perception. Variants of geometric ornamentation are proposed, which are obtained by means of parametric computer modeling, which can be used in the decoration of glass surfaces. Purpose. Application of the capabilities of parametric computer modeling CAD Autodesk Inventor in the design of block interior glazing. Methodology. The research methods consist in reviewing and analyzing modern trends in interior design and applying object-oriented modeling when creating multivariate three-dimensional models. Results. The advantages of using glazing elements in the interior design of premises for various purposes (residential, office, industrial) are considered. A parametric multivariate 3D model of the ornament of a modular glass surface is proposed. Scientific novelty is in the study of a change in the approach to design in the context of digitalization, in particular within the framework of the application of methods related to parametric modeling. Practical relevance is in the use of parameterization in computer modeling to ensure flexibility in changing the design. Thus, by changing several parameters, you can immediately get a new version of the ornament or design in one file of the Autodesk Inventor ipt part environment, in addition, this helps to save time during modeling, reduce material consumption during subsequent production, and speed up work on project visualization. Анотація. У статті розглянуто можливості застосування блочного скління в опорядженні інтер’єру та надано короткий історичний огляд популяризації даного виду скління як із погляду функціональних властивостей, так і з погляду естетичного сприйняття. Запропоновано варіанти геометричного орнаменту, які отримані засобом параметричного комп’ютерного моделювання, що можуть бути використані в оздобленні скляних поверхонь. Мета: застосування можливостей параметричного комп’ютерного моделювання САПР Autodesk Inventor у дизайні блочного інтер’єрного скління. Методологія. Методи дослідження полягають в огляді та аналізі сучасних тенденцій у дизайні інтер’єру та застосуванні об’єктно-орієнтованого моделювання під час створення багатоваріантних тривимірних моделей. Результати. Розглянуто переваги використання елементів скління в дизайні інтер’єру приміщень різних призначень (житлових, офісних, виробничих). Запропоновано параметричну багатоваріантну 3D-модель орнаменту модульної скляної поверхні. Наукова новизна полягає у дослідженні зміни підходу до дизайн-проєктування в умовах цифровізації, зокрема в рамках застосування методів, пов’язаних із параметричним моделюванням. Практична значущість полягає у використанні параметризації в комп’ютерному моделюванні для забезпечення гнучкості за зміни дизайну. Так, змінивши кілька параметрів, можна одразу отримати новий варіант орнаменту чи конструкції в одному файлі середовища деталі Autodesk Inventor ipt; окрім того, це сприяє економії часу під час моделювання, зменшенню витрат матеріалу за подальшого виробництва, пришвидшенню роботи над візуалізацією проєкту.
- 1 January 2025
- Published by Publishing House Helvetica (Publications) in Theory and practice of design
- No. 36,p. 313-319
Open AccessUSING AUTODESK INVENTOR PARAMETRIC MODELING IN GLASS SURFACES DESIGN
The article considers the options for using block glazing in interior decoration and provides a brief historical overview of the popularization of this type of glazing both from the point of view of functional properties and from the point of view of aesthetic perception. Variants of geometric ornamentation are proposed, which are obtained by means of parametric computer modeling, which can be used in the decoration of glass surfaces. Purpose. Application of the capabilities of parametric computer modeling CAD Autodesk Inventor in the design of block interior glazing. Methodology. The research methods consist in reviewing and analyzing modern trends in interior design and applying object-oriented modeling when creating multivariate three-dimensional models. Results. The advantages of using glazing elements in the interior design of premises for various purposes (residential, office, industrial) are considered. A parametric multivariate 3D model of the ornament of a modular glass surface is proposed. Scientific novelty is in the study of a change in the approach to design in the context of digitalization, in particular within the framework of the application of methods related to parametric modeling. Practical relevance is in the use of parameterization in computer modeling to ensure flexibility in changing the design. Thus, by changing several parameters, you can immediately get a new version of the ornament or design in one file of the Autodesk Inventor ipt part environment, in addition, this helps to save time during modeling, reduce material consumption during subsequent production, and speed up work on project visualization. Анотація. У статті розглянуто можливості застосування блочного скління в опорядженні інтер’єру та надано короткий історичний огляд популяризації даного виду скління як із погляду функціональних властивостей, так і з погляду естетичного сприйняття. Запропоновано варіанти геометричного орнаменту, які отримані засобом параметричного комп’ютерного моделювання, що можуть бути використані в оздобленні скляних поверхонь. Мета: застосування можливостей параметричного комп’ютерного моделювання САПР Autodesk Inventor у дизайні блочного інтер’єрного скління. Методологія. Методи дослідження полягають в огляді та аналізі сучасних тенденцій у дизайні інтер’єру та застосуванні об’єктно-орієнтованого моделювання під час створення багатоваріантних тривимірних моделей. Результати. Розглянуто переваги використання елементів скління в дизайні інтер’єру приміщень різних призначень (житлових, офісних, виробничих). Запропоновано параметричну багатоваріантну 3D-модель орнаменту модульної скляної поверхні. Наукова новизна полягає у дослідженні зміни підходу до дизайн-проєктування в умовах цифровізації, зокрема в рамках застосування методів, пов’язаних із параметричним моделюванням. Практична значущість полягає у використанні параметризації в комп’ютерному моделюванні для забезпечення гнучкості за зміни дизайну. Так, змінивши кілька параметрів, можна одразу отримати новий варіант орнаменту чи конструкції в одному файлі середовища деталі Autodesk Inventor ipt; окрім того, це сприяє економії часу під час моделювання, зменшенню витрат матеріалу за подальшого виробництва, пришвидшенню роботи над візуалізацією проєкту.
- Open Access
- 30 December 2024
- Published by Building Production, State Enterprise 'V.Balytskyi Scientific Research Institute of Building Production (SE 'NDIBV') in Building production
- No. 77,p. 3-10
OPTIMIZATION OF THE PARAMETERS OF REPAIR AND CONSTRUCTION WORKS DURING THE RESTORATION OF A REINFORCED CONCRETE PIPELINE
Reinforced concrete bridge structures have been widely erected in various countries since the middle of the 20th century. For such structures, problems of reduced durability due to damage from various influences are often found. Degradation mechanisms of structures significantly reduce the duration of safe operation. Rehabilitation and restoration of reinforced concrete of bridges and overpasses requires rational solutions for predicting the long-term strength of structures. Economic indicators of restoration are consistent with the duration of works, which is important for large cities. The presented studies reflect the optimization of structural and technological solutions during the capital repair of the overpass in Kyiv. The surveys carried out at the stage of project preparation did not give a complete reflection of the technical condition of the building for the preparation of final repair decisions, full information was obtained only after partial dismantling of the damaged structures. The support posts had corrosion of concrete and reinforcement, vertical stress cracks, delamination of concrete layers, leaching and locking of concrete. It is proposed to preserve part of the damaged structures of reinforced concrete supports with their strengthening. Removal of damaged concrete and exposure of working fittings, arrangement of additional reinforcing frame, external concreting of racks with a self-compacting mixture in fixed formwork made of metal pipes are provided for. The technology of restoration and reinforcement of the rack made it possible to preserve the existing reinforcement of the rack and its anchoring in the body of the bored pile. The removal of part of the damaged concrete was carried out in accordance with the sequence and volume of dismantling works. The reduction in the duration of restoration works, which is crucial in the conditions of intensive car traffic in the city, took place by 17%. The parameters of the bearing capacity and the design service life of the restored rack have been brought to the level of the parameters of the new design.
- 30 December 2024
- Published by Building Production, State Enterprise 'V.Balytskyi Scientific Research Institute of Building Production (SE 'NDIBV') in Building production
- No. 77,p. 3-10
Open AccessOPTIMIZATION OF THE PARAMETERS OF REPAIR AND CONSTRUCTION WORKS DURING THE RESTORATION OF A REINFORCED CONCRETE PIPELINE
Reinforced concrete bridge structures have been widely erected in various countries since the middle of the 20th century. For such structures, problems of reduced durability due to damage from various influences are often found. Degradation mechanisms of structures significantly reduce the duration of safe operation. Rehabilitation and restoration of reinforced concrete of bridges and overpasses requires rational solutions for predicting the long-term strength of structures. Economic indicators of restoration are consistent with the duration of works, which is important for large cities. The presented studies reflect the optimization of structural and technological solutions during the capital repair of the overpass in Kyiv. The surveys carried out at the stage of project preparation did not give a complete reflection of the technical condition of the building for the preparation of final repair decisions, full information was obtained only after partial dismantling of the damaged structures. The support posts had corrosion of concrete and reinforcement, vertical stress cracks, delamination of concrete layers, leaching and locking of concrete. It is proposed to preserve part of the damaged structures of reinforced concrete supports with their strengthening. Removal of damaged concrete and exposure of working fittings, arrangement of additional reinforcing frame, external concreting of racks with a self-compacting mixture in fixed formwork made of metal pipes are provided for. The technology of restoration and reinforcement of the rack made it possible to preserve the existing reinforcement of the rack and its anchoring in the body of the bored pile. The removal of part of the damaged concrete was carried out in accordance with the sequence and volume of dismantling works. The reduction in the duration of restoration works, which is crucial in the conditions of intensive car traffic in the city, took place by 17%. The parameters of the bearing capacity and the design service life of the restored rack have been brought to the level of the parameters of the new design.
- Open Access
- 29 November 2024
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 113,p. 205-226
Current state of development of permanent pontoon bridges and prospects for their construction in Ukraine
The history of the development of the most famous pontoon bridges, from ancient times to modern structures, is considered. The technical requirements for permanent pontoon bridges are systematized in accordance with the world experience in their design, construction, and operation. The most rational area of their application is outlined. The classification of permanent pontoon bridges according to the continuous and separate pontoon construction is presented. The variants of layout schemes depending on the peculiarities of their design, as well as variants of pontoon shape with a description of the peculiarities of their application are systematized. For reference, the table systematizes the main technical characteristics of modern permanent pontoon bridges located around the world. Modern projects of permanent pontoon bridges are considered in detail on the example of the coastal route E39, which is planned to be built in Norway using various bridge schemes, including cable-stayed and suspension bridges, as well as a floating tunnel. Conclusions are drawn regarding the further development of pontoon bridge structures in the future and the prospects for their construction in Ukraine.
- 29 November 2024
- Published by Kyiv National University of Construction and Architecture in Strength of Materials and Theory of Structures
- No. 113,p. 205-226
Open AccessCurrent state of development of permanent pontoon bridges and prospects for their construction in Ukraine
The history of the development of the most famous pontoon bridges, from ancient times to modern structures, is considered. The technical requirements for permanent pontoon bridges are systematized in accordance with the world experience in their design, construction, and operation. The most rational area of their application is outlined. The classification of permanent pontoon bridges according to the continuous and separate pontoon construction is presented. The variants of layout schemes depending on the peculiarities of their design, as well as variants of pontoon shape with a description of the peculiarities of their application are systematized. For reference, the table systematizes the main technical characteristics of modern permanent pontoon bridges located around the world. Modern projects of permanent pontoon bridges are considered in detail on the example of the coastal route E39, which is planned to be built in Norway using various bridge schemes, including cable-stayed and suspension bridges, as well as a floating tunnel. Conclusions are drawn regarding the further development of pontoon bridge structures in the future and the prospects for their construction in Ukraine.
- 30 October 2023
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 59 (5) , 24-31
Degradation of reinforced concrete constructions of bridge structures: corrosion aspect.
Factors, which cause fracture of reinforced concrete constructions of bridge structures were considered. One of them is anti-icing material used for road safety in the winter period. The Ukrainian market of anti-icing chemical reagents and combined agents of natural and industrial origin was analyzed. The kinetics of corrosion fracture of 09G2S and St3 steels as the main material of reinforcement in neutral chloride-containing and alkaline solutions was investigated using the method of polarization resistance. Taking into account the kinetics of corrosion fracture of the studied steels, the rate of their general corrosion was calculated.
- 30 October 2023
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Physicochemical Mechanics of Materials
- Vol. 59 (5) , 24-31
Degradation of reinforced concrete constructions of bridge structures: corrosion aspect.
Factors, which cause fracture of reinforced concrete constructions of bridge structures were considered. One of them is anti-icing material used for road safety in the winter period. The Ukrainian market of anti-icing chemical reagents and combined agents of natural and industrial origin was analyzed. The kinetics of corrosion fracture of 09G2S and St3 steels as the main material of reinforcement in neutral chloride-containing and alkaline solutions was investigated using the method of polarization resistance. Taking into account the kinetics of corrosion fracture of the studied steels, the rate of their general corrosion was calculated.
- Open Access
- 25 July 2023
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Chemistry and Technologies
- Vol. 31 (2) , 223-229
ТЕХНОЛОГІЧНІ ПАРАМЕТРИ ГАЛЬВАНОХІМІЧНИХ ПРОЦЕСІВ ФОРМУВАННЯ МЕТАЛОКСИДНИХ КОМПОЗИТІВ НА ОСНОВІ КОБАЛЬТУ
Electrodeposition of composite coatings based on cobalt, including refractory metals, allows obtaining coatings with a unique combination of physicochemical properties that cannot be achieved with other coating methods. The application of high-quality electrochemical composite coatings is only possible by establishing the characteristics of the electrolyte and electrolysis parameters. The characteristics of the scattering ability and specific electrical conductivity of Co-MoOx-WOx, Co-WOx-ZrO2, and Co-MoOx-ZrO2 electrolytes for depositing cobalt-based composite coatings have been established. The electrical conductivity values of the electrolytes for depositing cobalt-based composite coatings linearly increase with the temperature of the electrolyte, but their values at 25-30°C are sufficient for the deposition of high-quality coatings. It has been determined that within the current density range of 0.5–3.0 A/dm2 for Co-MoOx-WOx and up to 4.0 A/dm2 for Co-MoOx-ZrO2 and Co-WOx-ZrO2, the scattering ability remains above 85 %. The calculated activation energy of the electrical conductivity of complex electrolytes ranges from 22 to 29 kJ/mol, indicating the occurrence of mass transfer processes in the diffusion regime. Using insoluble inert stainless steel anodes in the technological process is justified.
- 25 July 2023
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Chemistry and Technologies
- Vol. 31 (2) , 223-229
Open AccessТЕХНОЛОГІЧНІ ПАРАМЕТРИ ГАЛЬВАНОХІМІЧНИХ ПРОЦЕСІВ ФОРМУВАННЯ МЕТАЛОКСИДНИХ КОМПОЗИТІВ НА ОСНОВІ КОБАЛЬТУ
Electrodeposition of composite coatings based on cobalt, including refractory metals, allows obtaining coatings with a unique combination of physicochemical properties that cannot be achieved with other coating methods. The application of high-quality electrochemical composite coatings is only possible by establishing the characteristics of the electrolyte and electrolysis parameters. The characteristics of the scattering ability and specific electrical conductivity of Co-MoOx-WOx, Co-WOx-ZrO2, and Co-MoOx-ZrO2 electrolytes for depositing cobalt-based composite coatings have been established. The electrical conductivity values of the electrolytes for depositing cobalt-based composite coatings linearly increase with the temperature of the electrolyte, but their values at 25-30°C are sufficient for the deposition of high-quality coatings. It has been determined that within the current density range of 0.5–3.0 A/dm2 for Co-MoOx-WOx and up to 4.0 A/dm2 for Co-MoOx-ZrO2 and Co-WOx-ZrO2, the scattering ability remains above 85 %. The calculated activation energy of the electrical conductivity of complex electrolytes ranges from 22 to 29 kJ/mol, indicating the occurrence of mass transfer processes in the diffusion regime. Using insoluble inert stainless steel anodes in the technological process is justified.
- Open Access
- 28 March 2023
- Published by Kharkiv National University of Radioelectronics in New Collegium
- Vol. 1 (110) , 59-64
Curator's work during the adaptation period of students at the Kharkiv National Automobile and Road University
Due to the transition to the new generation of educational standards and the increase in hours for independent work, there is a need to train a creative, active person who can independently choose his own life path. The educational process in the life of the university is planned and organized along with studies and scientific activities. The curator of the academic group is usually assigned an experimental teacher, since this position includes responsible and thorough work, which should take into account the profile of training of specialists and the specifics of the faculty. Students' problems related to the educational process at the university, interpersonal conflicts and relations in the group, and the question of the student group participation in the public and cultural mass activities of the university are resolved by the curator. The effectiveness of the educational work of the curator of the academic group is largely determined by its planning. Based on the analysis of theoretical studies and the experience of modern pedagogues-practitioners, the roles and functions of the curator in working with the group are defined, the curator's duties are described, and an approximate plan for the work of curators in universities is proposed. The views on the organization of educational work in higher education are presented. The creation of new mechanisms related to the selectivity of some disciplines makes it necessary to carry out additional explanatory and advisory work of curators regarding the formation of individual study plans for applicants. It is shown that the curator uses various forms of educational work in his activities, which contribute to the formation of the personality of the future specialist as a patriot citizen, who cares about the fate of the Ukrainian state, law, and order, education, and culture.
- 28 March 2023
- Published by Kharkiv National University of Radioelectronics in New Collegium
- Vol. 1 (110) , 59-64
Open AccessCurator's work during the adaptation period of students at the Kharkiv National Automobile and Road University
Due to the transition to the new generation of educational standards and the increase in hours for independent work, there is a need to train a creative, active person who can independently choose his own life path. The educational process in the life of the university is planned and organized along with studies and scientific activities. The curator of the academic group is usually assigned an experimental teacher, since this position includes responsible and thorough work, which should take into account the profile of training of specialists and the specifics of the faculty. Students' problems related to the educational process at the university, interpersonal conflicts and relations in the group, and the question of the student group participation in the public and cultural mass activities of the university are resolved by the curator. The effectiveness of the educational work of the curator of the academic group is largely determined by its planning. Based on the analysis of theoretical studies and the experience of modern pedagogues-practitioners, the roles and functions of the curator in working with the group are defined, the curator's duties are described, and an approximate plan for the work of curators in universities is proposed. The views on the organization of educational work in higher education are presented. The creation of new mechanisms related to the selectivity of some disciplines makes it necessary to carry out additional explanatory and advisory work of curators regarding the formation of individual study plans for applicants. It is shown that the curator uses various forms of educational work in his activities, which contribute to the formation of the personality of the future specialist as a patriot citizen, who cares about the fate of the Ukrainian state, law, and order, education, and culture.