OKOliver Kislat

Oliver Kislat

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Oliver Kislat has a total of 16 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Investigating the Impact of Steam Enhancement on Combustion in a Swirl-Assisted Jet-Stabilized Gas Turbine Combustor

    by Saeed Izadi, Oliver Kislat, Jan Zanger, Hannah Seliger-Ost, Peter Kutne, Manfred Aigner

    A newly developed gas turbine combustor system based on the swirl-assisted jet-stabilized concept using Jet A-1 and natural gas as reference fuel is tested under wet conditions to evaluate its combustion characteristics in the presence of steam. The effect of steam injection into the gas turbine combustor under both spray and superheated liquid fuel injection conditions is studied experimentally on an atmospheric test rig. To evaluate the effect of steam injection on combustion performance, the water-to-gas ratio (WGR) is varied from 0 to 32%. With increasing WGR = 0 to 16% and at stoichiometric condition, NOx reductions of -82% to -100% were observed during Jet A-1 and natural gas combustion, respectively. It is shown that the reduction of the combustion zone temperature due to the steam acting as a heat sink is the main cause of the NOx decrease. The operating range of the burner remained fairly constant for Jet A-1 until WGR = 20%, while it decreased significantly with increasing WGR for natural gas combustion. While the effect of the WGR on CO was modest, the greatest effect of the WGR was on the heat release zone intensity at a constant air to fuel ratio. In reducing the NOx levels of Jet A-1 and natural gas combustion, both thermal and chemical effects of steam injection were observed. However, steam acting as a heat sink and lowering the flame temperature, thereby reducing the thermal NO formation rate, was the dominant factor in NOx reduction.


  • Open Access

    Development and Testing of a Gas Turbine Test Rig Setup for Demonstrating New Aviation Propulsion Concepts

    by Oliver Kislat, Janos Römgens, Simon Schuldt, Jan Zanger, Nils Jakobs, Martin Henke, Cedric Kraus, Anika Moosbrugger, Mohamed Anes Asmi, Manfred Aigner

    To further increase efficiency and to significantly reduce climate impact in the aviation sector, new propulsion concepts must be developed. As full electrification in mid- and long-range aviation is impractical due to the low gravimetric energy density of batteries, new approaches must be developed. Therefore, the so-called hybrid electric ground demonstrator (HeBo), equipped with a Rolls Royce M250-C20B gas turbine is set up. The test rig serves as a development platform for various new gas turbine-based propulsion concepts for aviation, such as hybrid electric concepts or a novel cycle concept with steam injection to the combustor, which are described in this paper. The main focus of the work is on the experimental setup and the commissioning of the baseline test rig. This will place the test rig in the context of current research activities and serve as reference for subsequent research results.


  • Experimental Investigation of the Combustion Behavior of Single-Nozzle Liquid-FLOX®-Based Burners on an Atmospheric Test Rig

    by Saeed Izadi, Jan Zanger, Oliver Kislat, Benedict Enderle, Felix Grimm, Peter Kutne, Manfred Aigner

    As an alternative to the commonly used swirl burners in microgas turbines (MGT), the FLOX®-based combustion concept promises great potential for the nitric oxide emission reduction and increased fuel flexibility. Despite having to deal with a new set of challenges while utilizing liquid fuel in the burner, first steps are taken to gain more information on the influencing operational parameters. In this regard, a FLOX®-based liquid fuel burner is developed to fit into a newly designed combustor for the Capstone C30 MGT. The C30 combustor operates with three burners arranged tangentially to an annular combustion chamber and provides a total thermal power of 115 kW. In this work, operational properties of merely one of the three C30 liquid fuel burners are investigated and the rest of the two burners are emulated in form of hot cross-flow. As for the liquid burners, the experiments are conducted with three geometrically different single-nozzle burners at atmospheric pressure. The cross-flow is realized by utilizing a 20–nozzle FLOX®-based natural gas combustor. Measurements include visualization of the reaction zone and analysis of the exhaust gas emissions. By detecting the hydroxyl radical chemiluminescence (OH*-CL) emissions, the position of the heat release zone within the combustion chamber is attained. Correspondingly, the flame height above burner and the flame length are calculated. The investigated design parameters include air preheat temperature up to 733 K, equivalence ratio, burner geometry, and thermal power. Through variation of thermal power, the effect of liquid fuel preparation, i.e., atomization, evaporation, and mixing on combustion properties and exhaust gas emissions are examined. The results show that the burners with the medium diameter consistently performed remarkably at different flame temperatures and thermal powers. The lowest NOx and CO emissions for the medium diameter burner lied between 5 to 7 ppm and 8 to 10 ppm, respectively.


  • A Re-Design Study Based on a High Pressure Cyclonic Combustor Operated With Liquid Fuel

    by Felix Grimm, Benedict Enderle, Oliver Kislat, Saeed Izadi, Jan Zanger, Peter Kutne, Manfred Aigner

    Computational Fluid Dynamics are widely used as a design tool for a variety of thermo-fluid systems. Advantages of those numerical approaches are clearly the fairly detailed degree of valuable data at low computational costs, when RANS (Reynolds Averaged Navier Stokes) methods are used in the system design process. In this work, a combustion system operated at elevated pressure conditions is re-designed with CFD RANS methods. The combustor is operated with liquid fuel and is positioned between an upstream recuperation and a downstream turbine section. System design is carried out on the basis of a commercially available C30 configuration from the Capstone® Turbine Corporation. The micro turbine produces 30kW of electrical power and is therefore highly suited for micro gas turbine related applications. In the design process, as presented in the paper, several modifications are carried out. The system recuperation is changed, thus inflow modifications are given. Recuperation was explicitly simulated and is used as a combustor inflow boundary condition. The system is then analyzed and modified in terms of air splits in order to achieve certain combustion characteristics. Optimization is carried out for combustor air splits and turbine inlet temperature profile conditions are significantly improved. Reacting multi-phase simulations are used in order to characterize flow field and combustion. Further on, conjugated heat transfer is taken into account in order to characterize temperature distribution in the combustor. Additionally, combustor residence times are determined. It is demonstrated that the pursued methods and procedures are computationally cheap but at the same time highly suited and sufficient for thorough combustion system development.