György Barkó
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
György Barkó has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Gábor Kalácska
Hungarian University of Agriculture and Life Sciences
6 shared publications - Róbert Keresztes
Hungarian University of Agriculture and Life Sciences
5 shared publications - Ádám Kalácska
Soete Laboratory, Department of Electromechanical, Systems and Metal Engineering, Ghent University, Technologiepark 46, B-9052 Zwijnaarde, Belgium
4 shared publications - Hailemariam Shegawu
Mechanical Engineering Doctoral School, Magyar Agrár- és Élettudományi Egyetem (MATE), Páter K. u. 1., H-2100 Gödöllő, Hungary
3 shared publications - László Zsidai
Hungarian University of Agriculture and Life Sciences, Department of Materials Science and Engineering Processes, Institute of Technology
3 shared publications - Zoltán Károly
Institute of Materials and Environmental Chemistry, HUN-REN Research Centre for Natural Sciences, Budapest, Hungary
3 shared publications
Latest Publications
- Open Access
- 15 September 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (9) , 353
Torque-Based Assessment of Abrasive Wear in Rotating Shaft–Seal Systems Under Lunar Regolith Simulant
Despite extensive research on the abrasive properties of lunar regolith, the use of in-process tribological signals for wear assessment remains insufficiently studied. The aim of this work is to evaluate the relationship between torque response and abrasive wear severity in rotating shaft–seal systems exposed to lunar regolith simulants. Rotating EN 1.4404 stainless-steel shafts and spring-loaded natural polytetrafluoroethylene (PTFE) lip seals were tested under three-body abrasive wear conditions. Five particle-size fractions of LX-M100 Lunar Mare and LX-TH100 simulants were investigated at test durations of 15 min, 30 min and 1440 min. Frictional torque was continuously recorded, while post-test shaft surface roughness was used to characterize wear severity and Scanning Electron Microscope (SEM) analysis of the PTFE counterface was used to identify wear mechanisms. The results showed that torque response systematically depended on particle-size fraction and simulant type. Furthermore, the torque-response descriptors provide in-process information related to abrasive interaction severity, with peak torque events () showing the strongest relationship with abrasive surface modification. The statistical analysis was based on 27 complete observations, and considering the prematurely terminated test runs and the resulting limitations of the dataset, the obtained relationships are interpreted as exploratory. These findings provide a physical basis for torque-based wear monitoring in sealed rotating mechanisms for future lunar applications.- 15 September 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (9) , 353
Open AccessTorque-Based Assessment of Abrasive Wear in Rotating Shaft–Seal Systems Under Lunar Regolith Simulant
Despite extensive research on the abrasive properties of lunar regolith, the use of in-process tribological signals for wear assessment remains insufficiently studied. The aim of this work is to evaluate the relationship between torque response and abrasive wear severity in rotating shaft–seal systems exposed to lunar regolith simulants. Rotating EN 1.4404 stainless-steel shafts and spring-loaded natural polytetrafluoroethylene (PTFE) lip seals were tested under three-body abrasive wear conditions. Five particle-size fractions of LX-M100 Lunar Mare and LX-TH100 simulants were investigated at test durations of 15 min, 30 min and 1440 min. Frictional torque was continuously recorded, while post-test shaft surface roughness was used to characterize wear severity and Scanning Electron Microscope (SEM) analysis of the PTFE counterface was used to identify wear mechanisms. The results showed that torque response systematically depended on particle-size fraction and simulant type. Furthermore, the torque-response descriptors provide in-process information related to abrasive interaction severity, with peak torque events () showing the strongest relationship with abrasive surface modification. The statistical analysis was based on 27 complete observations, and considering the prematurely terminated test runs and the resulting limitations of the dataset, the obtained relationships are interpreted as exploratory. These findings provide a physical basis for torque-based wear monitoring in sealed rotating mechanisms for future lunar applications. - Open Access
- 12 August 2026
- Published by Cambridge University Press (CUP) in The Journal of Agricultural Science
- Vol. 164, 1-53
Agricultural potential of lunar regolith – a review on cultivation methodologies
Different methodologies have been reported in the literature for cultivation in extraplanetary regolith for Lunar, Mars, and Asteroid simulants. This review provides a comprehensive analysis of planting methods that use regolith as a plant growth substrate, highlighting species and environmental parameters controlled in research. It examines the nutritional adjustments and soil amendments necessary to enable cultivation, synthesizing findings from experiments documented in the literature. The review proposes an optimized methodology for future cultivation efforts and experimental designs by identifying disparities and successful cases. The ultimate goal of this report is to challenge researchers to master a regolith-based agricultural design that enables thriving plant ecosystems on the Moon and transforms regolith into a viable substrate for future space cultivation.
- 12 August 2026
- Published by Cambridge University Press (CUP) in The Journal of Agricultural Science
- Vol. 164, 1-53
Open AccessAgricultural potential of lunar regolith – a review on cultivation methodologies
Different methodologies have been reported in the literature for cultivation in extraplanetary regolith for Lunar, Mars, and Asteroid simulants. This review provides a comprehensive analysis of planting methods that use regolith as a plant growth substrate, highlighting species and environmental parameters controlled in research. It examines the nutritional adjustments and soil amendments necessary to enable cultivation, synthesizing findings from experiments documented in the literature. The review proposes an optimized methodology for future cultivation efforts and experimental designs by identifying disparities and successful cases. The ultimate goal of this report is to challenge researchers to master a regolith-based agricultural design that enables thriving plant ecosystems on the Moon and transforms regolith into a viable substrate for future space cultivation.
- Open Access
- 10 August 2026
- Published by Akademiai Kiado Zrt. in Progress in Agricultural Engineering Sciences
Sustainable plant cultivation in Lunar regolith: Feasibility study
Lunar regolith is a potential substrate for plant cultivation in future bioregenerative life-support systems; however, its distinct physicochemical properties pose challenges for plant growth. In this study, white mustard was grown in mare (LMS) and highland-type (LHS) regolith simulants, each separated into fine and coarse particle-size fractions, with perlite as a control. Germination was successful across all treatments. Biomass production and reproductive performance were generally lower in regolith simulants compared with the control. Plants grown in LMS produced slightly lighter seeds than those grown in LHS, with statistically significant differences observed in the LMS coarse fraction. These results likely reflect differences in simulant chemistry, as LMS contains higher concentrations of Fe, Mg, and trace elements that may influence plant physiological responses. Particle-size distribution also affected substrate behavior, with fine fractions showing higher water retention and coarse fractions improving aeration but reducing moisture availability. These results clarify that both substrate chemistry and particle size critically affect plant productivity in lunar regolith-based agriculture.
- 10 August 2026
- Published by Akademiai Kiado Zrt. in Progress in Agricultural Engineering Sciences
Open AccessSustainable plant cultivation in Lunar regolith: Feasibility study
Lunar regolith is a potential substrate for plant cultivation in future bioregenerative life-support systems; however, its distinct physicochemical properties pose challenges for plant growth. In this study, white mustard was grown in mare (LMS) and highland-type (LHS) regolith simulants, each separated into fine and coarse particle-size fractions, with perlite as a control. Germination was successful across all treatments. Biomass production and reproductive performance were generally lower in regolith simulants compared with the control. Plants grown in LMS produced slightly lighter seeds than those grown in LHS, with statistically significant differences observed in the LMS coarse fraction. These results likely reflect differences in simulant chemistry, as LMS contains higher concentrations of Fe, Mg, and trace elements that may influence plant physiological responses. Particle-size distribution also affected substrate behavior, with fine fractions showing higher water retention and coarse fractions improving aeration but reducing moisture availability. These results clarify that both substrate chemistry and particle size critically affect plant productivity in lunar regolith-based agriculture.
- Open Access
- 15 December 2025
- Published by Akademiai Kiado Zrt. in Progress in Agricultural Engineering Sciences
- Vol. 21 (1) , 201-214
IoT-based design for plant cultivation experiments and data logging
Recent advancements in low-cost microcontroller platforms and Internet of Things (IoT) sensors have enabled the development of automated, modular growth chambers for precise environmental control in plant studies. This study presents a cost-effective, scalable chamber equipped with Wi-Fi-enabled sensors for real-time monitoring of temperature, humidity, CO 2 , light intensity, and soil parameters. The system integrates an automated irrigation mechanism, programmable lighting, and cloud-based data management system. The design ensures independent sensor operation, preventing system-wide failures while maintaining experimental reproducibility. The results demonstrate that this approach significantly reduces costs while maintaining a reliable working system, providing high-resolution environmental control and making it suitable for diverse agricultural and botanical research applications.
- 15 December 2025
- Published by Akademiai Kiado Zrt. in Progress in Agricultural Engineering Sciences
- Vol. 21 (1) , 201-214
Open AccessIoT-based design for plant cultivation experiments and data logging
Recent advancements in low-cost microcontroller platforms and Internet of Things (IoT) sensors have enabled the development of automated, modular growth chambers for precise environmental control in plant studies. This study presents a cost-effective, scalable chamber equipped with Wi-Fi-enabled sensors for real-time monitoring of temperature, humidity, CO 2 , light intensity, and soil parameters. The system integrates an automated irrigation mechanism, programmable lighting, and cloud-based data management system. The design ensures independent sensor operation, preventing system-wide failures while maintaining experimental reproducibility. The results demonstrate that this approach significantly reduces costs while maintaining a reliable working system, providing high-resolution environmental control and making it suitable for diverse agricultural and botanical research applications.
- Open Access
- 22 March 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (4) , 136
Tribological Effects of Martian Regoliths on Stainless Steel with Natural and Composite Lip Seal and Packing Materials
We have investigated the sealing performance of different sealants and the abrasive effect of some Martian regolith simulants (MGS-1 and JEZ-1) by pin-on-disc tests using steel and various pin material pairs. Pin materials, representing sealants, were present in the following two forms: block types, such as pure polytetrafluoroethylene (PTFE) and composite PTFE, as well as braided pins, including pure and hybrid composite PTFE. Friction resistance, wear, surface roughness, and electron microscopy analyses were used to evaluate the tribological properties. We found significant differences between the block-type and braided pin materials regarding the sealing and wear performance. The braided pins either reached stabilized coefficients of friction at a much higher level (0.55) than the block-type pins or did not stabilize at all during the longest test duration. Martian regoliths resulted in negligible wear regarding the disc, but the hybrid composite braided pins were severely worn, causing the abrasion test to be stopped before schedule.
- 22 March 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (4) , 136
Open AccessTribological Effects of Martian Regoliths on Stainless Steel with Natural and Composite Lip Seal and Packing Materials
We have investigated the sealing performance of different sealants and the abrasive effect of some Martian regolith simulants (MGS-1 and JEZ-1) by pin-on-disc tests using steel and various pin material pairs. Pin materials, representing sealants, were present in the following two forms: block types, such as pure polytetrafluoroethylene (PTFE) and composite PTFE, as well as braided pins, including pure and hybrid composite PTFE. Friction resistance, wear, surface roughness, and electron microscopy analyses were used to evaluate the tribological properties. We found significant differences between the block-type and braided pin materials regarding the sealing and wear performance. The braided pins either reached stabilized coefficients of friction at a much higher level (0.55) than the block-type pins or did not stabilize at all during the longest test duration. Martian regoliths resulted in negligible wear regarding the disc, but the hybrid composite braided pins were severely worn, causing the abrasion test to be stopped before schedule.
- Open Access
- 22 January 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (2) , 43
Abrasion Behaviour of Natural and Composite Polytetrafluoroethylene Seal Materials Against Stainless Steel in Lunar Regolith Conditions
In this paper, the abrasive effects of lunar simulant regoliths (LHS-1, LMS-1) have been investigated. Sealing performance of different sealant pin materials on stainless steel has been tested by the pin-on-disc method. Pin materials included block types such as pure polytetrafluoroethylene (PTFE), composite PTFE, as well as braided PTFE and hybrid-composite braided PTFE. Tribological properties were evaluated based on measured friction, wear, surface roughness and scanning electron micrographs. Most significant differences were observed in the sealing effect of the pins between the braided and the block-type pin materials. The stainless steel/pin pairs showed significantly higher (0.4–0.5) friction coefficients for the braided pins than the block ones (0.2–0.3), while there was not a significant difference in the abrasive effect of the different lunar regoliths. Although significant wear of the steel part occurred only with the block-type pins, this disadvantage was apparent in comparison with the braided pins. The abrasive particles caused deformation and eventually complete disintegration of the braided pins. Both the coefficient of friction and the wear could be estimated by a multiple linear regression model, in which different regolith size was the dominant independent parameter for the various pins.
- 22 January 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (2) , 43
Open AccessAbrasion Behaviour of Natural and Composite Polytetrafluoroethylene Seal Materials Against Stainless Steel in Lunar Regolith Conditions
In this paper, the abrasive effects of lunar simulant regoliths (LHS-1, LMS-1) have been investigated. Sealing performance of different sealant pin materials on stainless steel has been tested by the pin-on-disc method. Pin materials included block types such as pure polytetrafluoroethylene (PTFE), composite PTFE, as well as braided PTFE and hybrid-composite braided PTFE. Tribological properties were evaluated based on measured friction, wear, surface roughness and scanning electron micrographs. Most significant differences were observed in the sealing effect of the pins between the braided and the block-type pin materials. The stainless steel/pin pairs showed significantly higher (0.4–0.5) friction coefficients for the braided pins than the block ones (0.2–0.3), while there was not a significant difference in the abrasive effect of the different lunar regoliths. Although significant wear of the steel part occurred only with the block-type pins, this disadvantage was apparent in comparison with the braided pins. The abrasive particles caused deformation and eventually complete disintegration of the braided pins. Both the coefficient of friction and the wear could be estimated by a multiple linear regression model, in which different regolith size was the dominant independent parameter for the various pins.
- Open Access
The Abrasive Effect of Moon and Mars Regolith Simulants on Stainless Steel Rotating Shaft and Polytetrafluoroethylene Sealing Material Pairs
For space missions to either the Moon or Mars, protecting mechanical moving parts from the abrasive effects of prevailing surface dust is crucial. This paper compares the abrasive effects of two lunar and two Martian simulant regoliths using special pin-on-disc tests on a stainless steel/polytetrafluoroethylene (PTFE) sealing material pair. Due to the regolith particles entering the contact zone, a three-body abrasion mechanism took place. We found that friction coefficients stabilised between 0.2 and 0.4 for all simulants. Wear curves, surface roughness measurements, and microscopic images all suggest a significantly lower abrasion effect of the Martian regoliths than that of the lunar ones. It applies not only to steel surfaces but also to the PTFE pins. The dominant abrasive micro-mechanism of the disc surface is micro-ploughing in the case of all tests, while the transformation of the counterface is mixed. The surface of pin material is plastically transformed through micro-ploughing, while the material is removed through micro-cutting due to the slide over hard soil particles.
Open AccessThe Abrasive Effect of Moon and Mars Regolith Simulants on Stainless Steel Rotating Shaft and Polytetrafluoroethylene Sealing Material Pairs
For space missions to either the Moon or Mars, protecting mechanical moving parts from the abrasive effects of prevailing surface dust is crucial. This paper compares the abrasive effects of two lunar and two Martian simulant regoliths using special pin-on-disc tests on a stainless steel/polytetrafluoroethylene (PTFE) sealing material pair. Due to the regolith particles entering the contact zone, a three-body abrasion mechanism took place. We found that friction coefficients stabilised between 0.2 and 0.4 for all simulants. Wear curves, surface roughness measurements, and microscopic images all suggest a significantly lower abrasion effect of the Martian regoliths than that of the lunar ones. It applies not only to steel surfaces but also to the PTFE pins. The dominant abrasive micro-mechanism of the disc surface is micro-ploughing in the case of all tests, while the transformation of the counterface is mixed. The surface of pin material is plastically transformed through micro-ploughing, while the material is removed through micro-cutting due to the slide over hard soil particles.
- Open Access
- 7 August 2023
- Published by MDPI AG in Lubricants
- Vol. 11 (8) , 334
Abrasion Evaluation of Moon and Mars Simulants on Rotating Shaft/Sealing Materials: Simulants and Structural Materials Review and Selection
Tribological testing of moving shaft/sealing pairs in complex environments is at the frontline of research. Machines working in abrasive conditions are subject to different wear effects. It is not only valid on Earth but especially valid for rovers and future robots used in Mars and Moon missions. The aim of our joint research with the European Space Agency is to study the abrasion phenomena of moving machine elements on Mars and the Moon by using artificial soil samples (“simulants”). This review details mainly the available simulant sources and recommend a selection of the most suitable ones for tribological testing. Moreover, the potential mating structural materials subjected to abrasive space applications are reviewed briefly. The tribological tests are exploring the features of the rotary shaft/seal relationship that is subject to dry friction and intense abrasion. By using the simulants, measurements are performed under laboratory conditions with both a sample test and a real shaft/seal connection. Parameters of the selection criteria were defined, and classification of the simulant sources were made. It was found that simulant particle size distribution and chemical substance content are detailed enough only for a limited type of available artificial Moon and Mars soil samples. Four simulants were identified and applied later in the tribological testing. For the shaft materials, based on a detailed case study of polymers, steel, and aluminum alloys, a high-strength aluminum alloy with a hard anodized surface and a stainless steel were selected for further abrasion tests.
- 7 August 2023
- Published by MDPI AG in Lubricants
- Vol. 11 (8) , 334
Open AccessAbrasion Evaluation of Moon and Mars Simulants on Rotating Shaft/Sealing Materials: Simulants and Structural Materials Review and Selection
Tribological testing of moving shaft/sealing pairs in complex environments is at the frontline of research. Machines working in abrasive conditions are subject to different wear effects. It is not only valid on Earth but especially valid for rovers and future robots used in Mars and Moon missions. The aim of our joint research with the European Space Agency is to study the abrasion phenomena of moving machine elements on Mars and the Moon by using artificial soil samples (“simulants”). This review details mainly the available simulant sources and recommend a selection of the most suitable ones for tribological testing. Moreover, the potential mating structural materials subjected to abrasive space applications are reviewed briefly. The tribological tests are exploring the features of the rotary shaft/seal relationship that is subject to dry friction and intense abrasion. By using the simulants, measurements are performed under laboratory conditions with both a sample test and a real shaft/seal connection. Parameters of the selection criteria were defined, and classification of the simulant sources were made. It was found that simulant particle size distribution and chemical substance content are detailed enough only for a limited type of available artificial Moon and Mars soil samples. Four simulants were identified and applied later in the tribological testing. For the shaft materials, based on a detailed case study of polymers, steel, and aluminum alloys, a high-strength aluminum alloy with a hard anodized surface and a stainless steel were selected for further abrasion tests.
- Open Access
- 15 June 2023
- Published by MDPI AG in Preprints.org
Abrasion Evaluation of Moon and Mars Simulants on Rotating Shaft/Sealing Materials: Simulants and Structural Materials Review and Selection
Tribological testing of moving shaft/sealing pairs in complex environments is at the frontline of research. Machines working in abrasive conditions are subject to different wear effects. It is valid not only on the Earth but especially valid for rovers and future robots used in Mars and Moon missions. The aim of our joint research with the European Space Agency is to study the abrasion phenomena of moving machine elements on Mars and the Moon, by using artificial soil samples (“simulants”). This review detail the available simulant sources and recommend a selection of the most suitable ones for tribological testing. Moreover, the potential mating structural materials subjected to abrasive space applications are reviewed. The tribological tests are exploring the features of the rotary shaft/seal relationship that is subject to dry friction and intense abrasion. By using the simulants, measurements are performed under laboratory conditions with both a sample test and a real shaft/seal connection. Parameters of the selection criteria have been defined and classification of the simulant sources were made. It was found that simulant particle size distribution and chemical substance content is detailed enough only for a limited type of available artificial Moon and Mars soil samples. 4 simulants have been identified and applied later in the tribological testing. For the shaft materials, based on a detailed case study of polymers, steel and aluminium alloys, a high-strength aluminium alloy with a hard anodized surface and a stainless steel were selected for further abrasion tests.
- 15 June 2023
- Published by MDPI AG in Preprints.org
Open AccessAbrasion Evaluation of Moon and Mars Simulants on Rotating Shaft/Sealing Materials: Simulants and Structural Materials Review and Selection
Tribological testing of moving shaft/sealing pairs in complex environments is at the frontline of research. Machines working in abrasive conditions are subject to different wear effects. It is valid not only on the Earth but especially valid for rovers and future robots used in Mars and Moon missions. The aim of our joint research with the European Space Agency is to study the abrasion phenomena of moving machine elements on Mars and the Moon, by using artificial soil samples (“simulants”). This review detail the available simulant sources and recommend a selection of the most suitable ones for tribological testing. Moreover, the potential mating structural materials subjected to abrasive space applications are reviewed. The tribological tests are exploring the features of the rotary shaft/seal relationship that is subject to dry friction and intense abrasion. By using the simulants, measurements are performed under laboratory conditions with both a sample test and a real shaft/seal connection. Parameters of the selection criteria have been defined and classification of the simulant sources were made. It was found that simulant particle size distribution and chemical substance content is detailed enough only for a limited type of available artificial Moon and Mars soil samples. 4 simulants have been identified and applied later in the tribological testing. For the shaft materials, based on a detailed case study of polymers, steel and aluminium alloys, a high-strength aluminium alloy with a hard anodized surface and a stainless steel were selected for further abrasion tests.