Suresh Sethu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Suresh Sethu has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
C. Pownraj
4 shared publications- Kalimuthu Mayandi
Department of Mechanical Engineering, Kalasalingam Academy of Research and Education Anand Nagar, Krishnankoil-626126, Virudhunagar Dt, India
4 shared publications A. Valan Arasu
3 shared publications- Faruq Mohammad
College of Science, King Saud University
3 shared publications M. Murali
Kalasalingam Academy of Research and Education
3 shared publicationsMayandi Kalimuthu
Department of Mechanical Engineering, Kalasalingam Academy of Research and Education, Krishnankoil-626126, Tamilnadu, India
3 shared publications
Latest Publications
- Open Access
- 9 July 2026
- Published by Elsevier in Next Materials
- Vol. 13
Laser-thermal-induced dual-surface modification of copper: Influence of morphology and oxidation on wettability and water spreading behaviour
- 9 July 2026
- Published by Elsevier in Next Materials
- Vol. 13
Open AccessLaser-thermal-induced dual-surface modification of copper: Influence of morphology and oxidation on wettability and water spreading behaviour
- 1 January 2026
- Published by BioResources in BioResources
- Vol. 21 (4)
Thermal analysis and tribological characterization of bamboo-fiber-reinforced polylactic acid composites
Bamboo-fiber-reinforced polylactic acid (B-PLA) composites have emerged as promising materials for sustainable engineering applications due to their biodegradability, favorable mechanical properties, and renewability. This work systematically evaluated the thermal behavior and tribological performance of B-PLA composites using methods such as Vicat softening temperature measurement (VST), thermogravimetric analysis (TGA), and abrasive wear testing under varying loads, distances, and abrasive types. The results demonstrated that bamboo fiber reinforcement significantly increased the Vicat softening temperature compared with neat PLA, indicating enhanced thermal resistance. Thermogravimetric analysis revealed that the maximum degradation temperatures of the composites (303 to 317 °C) were comparable to neat PLA, confirming good thermal stability without phase separation. Tribological evaluation showed that specimens fabricated at a nozzle temperature of 245 °C exhibited approximately 37.5% lower wear mass loss than those fabricated at 195 °C, owing to improved interfacial bonding and higher surface hardness. Furthermore, Al₂O₃ abrasives produced the highest wear because of their greater hardness and density, while SEM observations confirmed reduced abrasive embedding and improved fiber-matrix adhesion in high-temperature processed composites. These findings demonstrate that optimized FDM processing significantly enhanced the thermal and wear performance of sustainable bamboo/PLA composites.
- 1 January 2026
- Published by BioResources in BioResources
- Vol. 21 (4)
Thermal analysis and tribological characterization of bamboo-fiber-reinforced polylactic acid composites
Bamboo-fiber-reinforced polylactic acid (B-PLA) composites have emerged as promising materials for sustainable engineering applications due to their biodegradability, favorable mechanical properties, and renewability. This work systematically evaluated the thermal behavior and tribological performance of B-PLA composites using methods such as Vicat softening temperature measurement (VST), thermogravimetric analysis (TGA), and abrasive wear testing under varying loads, distances, and abrasive types. The results demonstrated that bamboo fiber reinforcement significantly increased the Vicat softening temperature compared with neat PLA, indicating enhanced thermal resistance. Thermogravimetric analysis revealed that the maximum degradation temperatures of the composites (303 to 317 °C) were comparable to neat PLA, confirming good thermal stability without phase separation. Tribological evaluation showed that specimens fabricated at a nozzle temperature of 245 °C exhibited approximately 37.5% lower wear mass loss than those fabricated at 195 °C, owing to improved interfacial bonding and higher surface hardness. Furthermore, Al₂O₃ abrasives produced the highest wear because of their greater hardness and density, while SEM observations confirmed reduced abrasive embedding and improved fiber-matrix adhesion in high-temperature processed composites. These findings demonstrate that optimized FDM processing significantly enhanced the thermal and wear performance of sustainable bamboo/PLA composites.
- Open Access
- 1 April 2025
- Published by Elsevier in Hybrid Advances
- Vol. 10
Investigation of atmospheric moisture interaction on modified copper surfaces using thermoelectric cooling
- 1 April 2025
- Published by Elsevier in Hybrid Advances
- Vol. 10
Open AccessInvestigation of atmospheric moisture interaction on modified copper surfaces using thermoelectric cooling
- 26 August 2024
- Published by Springer Nature in Interactions
- Vol. 245 (1) , 1-11
The effect of infill density on tensile properties of 3D printed chopped carbon fiber reinforced PLA composites materials
- 26 August 2024
- Published by Springer Nature in Interactions
- Vol. 245 (1) , 1-11
The effect of infill density on tensile properties of 3D printed chopped carbon fiber reinforced PLA composites materials
- 19 August 2024
- Published by Springer Nature in Interactions
- Vol. 245 (1) , 1-11
Production and characterization of biodegradable polylactic acid composites 3D filament from agro waste
- 19 August 2024
- Published by Springer Nature in Interactions
- Vol. 245 (1) , 1-11
Production and characterization of biodegradable polylactic acid composites 3D filament from agro waste
- 6 July 2024
- Published by Springer Nature in Interactions
- Vol. 245 (1) , 1-20
Tribological investigations on fibre-reinforced composites: a comprehensive review considering variable velocity and load scenarios
- 6 July 2024
- Published by Springer Nature in Interactions
- Vol. 245 (1) , 1-20
Tribological investigations on fibre-reinforced composites: a comprehensive review considering variable velocity and load scenarios
- Open Access
- 28 June 2024
- Published by Elsevier in International Journal of Thermofluids
- Vol. 23
Cu MOF-biocarbon functional catalysts as adsorbent for oxygen-linked carbon capture via thermo-catalytic pyrolysis: A low-carbon fuel synthesis strategy
- 28 June 2024
- Published by Elsevier in International Journal of Thermofluids
- Vol. 23
Open AccessCu MOF-biocarbon functional catalysts as adsorbent for oxygen-linked carbon capture via thermo-catalytic pyrolysis: A low-carbon fuel synthesis strategy