Sivaprakash Ethiraj
Sivaprakash Ethiraj has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Rathinavelu Venkatesh
Department of Mechanical Engineering, Saveetha School of Engineering, Saveetha Institute of Medical and Technical Sciences, SIMATS, Chennai, India
2 shared publications - Balamurugan Mani
Saveetha School of Engineering, Saveetha Institute of Medical and Technical Sciences
1 shared publication - Deepika Gabiriel
College of Engineering and Technology, Aksum University, Aksum, Ethiopia
1 shared publication - K. R. Padmavathi
Department of Mechanical Engineering, Panimalar Engineering College, Chennai, India
1 shared publication - N. Karthikeyan
Department of Mechanical Engineering, K.Ramakrishnan College of Engineering, Trichy, India
1 shared publication - Ratchagaraja Dhairiyasamy
Saveetha School of Engineering, Department of Electronics and Communication Engineering, Saveetha Institute of Medical and Technical Sciences (SIMATS), Saveetha University, Chennai, India
1 shared publication
Latest Publications
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 30, e20240598
Spray characteristics of non-edible oils in MQL systems for improved material machining
This study investigates the spray characteristics of non-edible oils, specifically Rapeseed, Jatropha, Neem, and Coconut oils, in Minimum Quantity Lubrication (MQL) systems using Computational Fluid Dynamics (CFD) simulations. The objective was to analyze the effects of MQL parameters—such as inlet air pressure, flow rate, and nozzle diameter—and fluid properties on droplet velocity and diameter. A Discrete Phase Model (DPM) was employed within the CFD framework to simulate the atomization process. Results indicated that increased inlet pressure significantly reduced droplet diameter, with a maximum reduction of 68.35% observed in Coconut oil. Similarly, an increase in flow rate and nozzle diameter led to higher droplet velocities, with the maximum velocity reaching 238.59% of its initial value in Jatropha oil at 6 bar pressure. Viscosity was identified as the most influential fluid property on droplet size, demonstrating a direct relationship with increased droplet diameter. The findings highlight the importance of optimizing MQL parameters and fluid properties to enhance machining performance and reduce environmental impact.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in Matéria (Rio de Janeiro)
- Vol. 30, e20240598
Open AccessSpray characteristics of non-edible oils in MQL systems for improved material machining
This study investigates the spray characteristics of non-edible oils, specifically Rapeseed, Jatropha, Neem, and Coconut oils, in Minimum Quantity Lubrication (MQL) systems using Computational Fluid Dynamics (CFD) simulations. The objective was to analyze the effects of MQL parameters—such as inlet air pressure, flow rate, and nozzle diameter—and fluid properties on droplet velocity and diameter. A Discrete Phase Model (DPM) was employed within the CFD framework to simulate the atomization process. Results indicated that increased inlet pressure significantly reduced droplet diameter, with a maximum reduction of 68.35% observed in Coconut oil. Similarly, an increase in flow rate and nozzle diameter led to higher droplet velocities, with the maximum velocity reaching 238.59% of its initial value in Jatropha oil at 6 bar pressure. Viscosity was identified as the most influential fluid property on droplet size, demonstrating a direct relationship with increased droplet diameter. The findings highlight the importance of optimizing MQL parameters and fluid properties to enhance machining performance and reduce environmental impact.
- 3 February 2024
- Published by Springer Nature in Silicon
- Vol. 16 (6) , 2771-2779
SiC Blending Behaviour of Hybrid AZ31 Alloy Nanocomposite: Metallographic and Mechanical Studies
- 3 February 2024
- Published by Springer Nature in Silicon
- Vol. 16 (6) , 2771-2779
SiC Blending Behaviour of Hybrid AZ31 Alloy Nanocomposite: Metallographic and Mechanical Studies