ZQZhirong Qu

Zhirong Qu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zhirong Qu has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Preparation of Acryloxyl Group Functionalized Siloxane Polymers and the Study of Their Ultra Violet Curing Properties

    by Dan Du, Xupeng Chen, Yue Wu, Chuan Wu, Zhirong Qu, Yanjiang Song, Dawei Qin, Qiao Li, Hong Dong

    Polysiloxane with multiple acryloxyl groups at the terminal site of the polymer chain was synthesized by the condensation reaction between hydroxyl-terminated polysiloxane and acryloyl chloride and used to improve the cross-linking density of UV-curable silicone materials initiated from dual acryloxy-terminated symmetric polysiloxane or single acryloxy-terminated asymmetric polysiloxane with the mixture of Irgacure 1173 and Irgacure 184 at a mass ratio of 1:1 as the photoinitiator. The effects of factors such as initiator composition, UV irradiation time, structure, and molecular weight of linear dual acryloxy-terminated or single acryloxy-terminated asymmetric siloxane oligomers on the gelation yield, thermal properties, water absorption, and water contact angle of UV-cured film were investigated. The synthesized cross-linking density modifier can be copolymerized with acryloxy-functionalized linear polysiloxanes under the action of a photoinitiator to increase the cross-link density of UV-cured products effectively. Both linear dual acryloxy-terminated or single acryloxy-terminated asymmetric siloxane oligomers can be copolymerized with cross-link density modifiers within 20 s of UV irradiation. The gelation yields of the UV-cured products obtained from the dual acryloxy-terminated siloxane oligomers were greater than 85%, and their surface water contact angles increased from 72.8° to 95.9° as the molecular weight of the oligomers increased. The gelation yields of UV-cured products obtained from single acryloxy-terminated asymmetric siloxane oligomers were less than 80%, and their thermal stabilities were inferior to those obtained from the dual acryloxy-terminated siloxane oligomers. However, the water contact angles of UV-cured products obtained from these single acryloxy-terminated asymmetric siloxane oligomers were all greater than 90°.


  • Open Access

    Preparation of Monotrimethoxylsilylethyl-Terminated Polysiloxane Fluids and Their Application in Thermal Interface Materials

    by Yang Liu, Xu Long, Yang Wang, Chuan Wu, Zhirong Qu, Zhiwei Pei, Chunlong Shi, Ting Wang, Hong Dong

    In this study, α-Trimethylsilylmethyl-ω-dimethylsilyl-terminated polydimethylsiloxane, polydiethylsiloxane and poly[2,2,2-trifluoropropyl(methyl)siloxane] are synthesized using an anion catalyzed nonequilibrium polymerization reaction with trimethylsilylmethyl lithium as the initiator; hexamethylcyclotrisiloxane, hexaethylcyclotrisiloxane or 1,3,5-trimethyl-1,3,5-trifluoropropylcyclotrisiloxane as the monomer; and dimethylchlorosilane as an end-capping agent. Three kinds of α-trimethylsilylmethyl-ω-trimethoxylsilylethyl-terminated polysiloxanes are further prepared by hydrosilylation reaction of α-trimethylsilylmethyl-ω-dimethylsilyl-terminated polysiloxanes with vinyltrimethoxysilane using Karstedt’s catalyst. These α-trimethylsilylmethyl-ω-trimethoxylsilylethyl-terminated polysiloxanes are functionalized as in situ surface treatment agents for AlN particles. The effects of the structure of these polysiloxanes on the dispersion of AlN in the polysiloxane matrix and on the heat transfer performance of silicone pastes and silicone rubbers are investigated. A possible mechanism of surface treatment of AlN fillers by these novel silicone fluids is also discussed.