Jilei Chao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jilei Chao has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Fuqiang Chu
School of Energy and Environmental Engineering University of Science and Technology Beijing Beijing China
1 shared publication - Fuqiang Chu
Faculty of Light Industry, Qilu University of Technology (Shandong Academy of Sciences), Jinan 250353, China
1 shared publication - Haikuo Zhang
Faculty of Light Industry, Qilu University of Technology (Shandong Academy of Sciences), Jinan 250353, China
1 shared publication - Jiajun Liu
Faculty of Light Industry, Qilu University of Technology (Shandong Academy of Sciences), Jinan 250353, China
1 shared publication - Jilei Chao
Faculty of Light Industry, Qilu University of Technology (Shandong Academy of Sciences), Jinan 250353, China
1 shared publication - Ruizhi Shi
Information Engineering University, Zhengzhou 450001, China
1 shared publication
Latest Publications
- Open Access
Glycerol/NaCl-Regulated Poly(vinyl alcohol)/Sodium Alginate/Graphene Oxide Composite Gels with Low-Temperature Flexibility and a Strain-Dependent Resistance Response
Flexible gel sensors can lose mechanical compliance and electrical stability at low temperature or during solvent loss. A poly(vinyl alcohol) (PVA)/sodium alginate (SA)/graphene oxide (GO) composite gel was prepared by freeze–thaw cycling and post-treated in either aqueous NaCl or a NaCl-containing water/glycerol mixture (1:2, v/v). The water/glycerol–NaCl-treated gel (F-G/S/P/G) exhibited a maximum tensile stress of 428 ± 27 kPa and an elongation at break of 432 ± 27% at room temperature (n = 3), and remained visibly deformable after 24 h at −20 °C. During ambient storage, it retained approximately 89% of its initial mass after 35 days. The cycle-averaged peak ΔR/R0 increased from 0.135 at 20% strain to 1.142 at 250% strain, and the 20–60% linear region gave a gauge factor of 1.01 (R2 = 0.9988). Three independently prepared sensing elements gave a peak ΔR/R0 of 0.710 ± 0.019 at 100% strain, with response and recovery times of 1.22 ± 0.07 and 1.04 ± 0.06 s, respectively. After 500 cycles at 100% strain, the normalized peak response retained 95.1% of its initial value. Overall, F-G/S/P/G combined low-temperature deformability, ambient-storage mass retention, and repeatable resistance sensing.
Open AccessGlycerol/NaCl-Regulated Poly(vinyl alcohol)/Sodium Alginate/Graphene Oxide Composite Gels with Low-Temperature Flexibility and a Strain-Dependent Resistance Response
Flexible gel sensors can lose mechanical compliance and electrical stability at low temperature or during solvent loss. A poly(vinyl alcohol) (PVA)/sodium alginate (SA)/graphene oxide (GO) composite gel was prepared by freeze–thaw cycling and post-treated in either aqueous NaCl or a NaCl-containing water/glycerol mixture (1:2, v/v). The water/glycerol–NaCl-treated gel (F-G/S/P/G) exhibited a maximum tensile stress of 428 ± 27 kPa and an elongation at break of 432 ± 27% at room temperature (n = 3), and remained visibly deformable after 24 h at −20 °C. During ambient storage, it retained approximately 89% of its initial mass after 35 days. The cycle-averaged peak ΔR/R0 increased from 0.135 at 20% strain to 1.142 at 250% strain, and the 20–60% linear region gave a gauge factor of 1.01 (R2 = 0.9988). Three independently prepared sensing elements gave a peak ΔR/R0 of 0.710 ± 0.019 at 100% strain, with response and recovery times of 1.22 ± 0.07 and 1.04 ± 0.06 s, respectively. After 500 cycles at 100% strain, the normalized peak response retained 95.1% of its initial value. Overall, F-G/S/P/G combined low-temperature deformability, ambient-storage mass retention, and repeatable resistance sensing.
- Open Access
Preparation and Properties of Inkjet Waterborne Coatings
As an environmentally friendly coating, waterborne coatings have broad application prospects in paper packaging products in food and medicine. In this paper, a waterborne coating is synthesized from epoxy resin, polypropylene glycol diglycidyl ether, acrylic acid, trimellitic anhydride, maleic anhydride, and organic amine by three steps: ring opening reaction, esterification reaction, and neutralization reaction. Using viscosity, particle size, thermal stability, adhesion, and friction resistance as performance evaluation factors, the effects of the ratios of epoxy resin and polypropylene glycol diglycidyl ether in the polymerization system on the performance of synthetic waterborne coatings were discussed. Taking water solubility, water absorption, and water resistance as performance evaluation factors, the effects of the amount of ratio of anhydride groups to hydroxyl groups in the epoxy acrylic resin, which were produced in the second step of the reaction, were considered on the performance of synthetic waterborne coatings. The experimental results showed that when the molar ratio of the epoxy group in the epoxy resin and polypropylene glycol diglycidyl ether was about 1:1, and the molar ratio of anhydride in maleic anhydride to hydroxyl in the epoxy acrylic resin generated in the second step of reaction was about 0.9:1, the performance of the prepared waterborne coatings was comprehensively better. At the same time, the applicability of self-made waterborne coatings was tested. The results showed that when the coating amount was about 3.60 g/m2, the properties of the packaging base paper were greatly improved with respect to air resistance, oxygen resistance, oil resistance, and color reproducibility.
Open AccessPreparation and Properties of Inkjet Waterborne Coatings
As an environmentally friendly coating, waterborne coatings have broad application prospects in paper packaging products in food and medicine. In this paper, a waterborne coating is synthesized from epoxy resin, polypropylene glycol diglycidyl ether, acrylic acid, trimellitic anhydride, maleic anhydride, and organic amine by three steps: ring opening reaction, esterification reaction, and neutralization reaction. Using viscosity, particle size, thermal stability, adhesion, and friction resistance as performance evaluation factors, the effects of the ratios of epoxy resin and polypropylene glycol diglycidyl ether in the polymerization system on the performance of synthetic waterborne coatings were discussed. Taking water solubility, water absorption, and water resistance as performance evaluation factors, the effects of the amount of ratio of anhydride groups to hydroxyl groups in the epoxy acrylic resin, which were produced in the second step of the reaction, were considered on the performance of synthetic waterborne coatings. The experimental results showed that when the molar ratio of the epoxy group in the epoxy resin and polypropylene glycol diglycidyl ether was about 1:1, and the molar ratio of anhydride in maleic anhydride to hydroxyl in the epoxy acrylic resin generated in the second step of reaction was about 0.9:1, the performance of the prepared waterborne coatings was comprehensively better. At the same time, the applicability of self-made waterborne coatings was tested. The results showed that when the coating amount was about 3.60 g/m2, the properties of the packaging base paper were greatly improved with respect to air resistance, oxygen resistance, oil resistance, and color reproducibility.