Zhaobo Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhaobo Liu has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Chengyu Huang
School of Materials Science and Engineering, Beihang University, Beijing 100191, China
1 shared publication - Guanlong Li
School of Materials Science and Engineering, Beihang University, Beijing 100191, China
1 shared publication - Hansong Liu
AVIC Manufacturing Technology Institute Composite Technology Center, Beijing 101300, China
1 shared publication - Jianwen Bao
AVIC Manufacturing Technology Institute Composite Technology Center, Beijing 101300, China
1 shared publication - Jinsong Sun
AVIC Manufacturing Technology Institute Composite Technology Center, Beijing 101300, China
1 shared publication - Kai Wang
School of Materials Science and Engineering, Beihang University, Beijing 100191, China
1 shared publication
Latest Publications
- Open Access
Influence of the Second-Phase Resin Structure on the Interfacial Shear Strength of Carbon Fiber/Epoxy Resin
The toughening modification of epoxy resin has received widespread attention. The addition of the second-phase resin has a good toughening effect on epoxy resin. In order to investigate the effect of the second-phase resin on the interphase of composites, in this work the interfacial properties of carbon fiber (CF)/epoxy resin with the second-phase resin structure were investigated. Methodologies including surface structure observation, chemical characteristics, surface energy of the CF, and micro-phase structure characterization of resin were tested, followed by the micro-interfacial performance of CF/epoxy composites before and after hygrothermal treatment. The results revealed that the sizing process has the positive effect of increasing the interfacial bonding properties of CF/epoxy. From the interfacial shear strength (IFSS) test, the introduction of the second phase in the resin reduced the interfacial bonding performance between the CF and epoxy. After the hygrothermal treatment, water molecules diffused along the interfacial paths between the two resins, which in turn created defects and consequently brought about a reduction in the IFSS.
Open AccessInfluence of the Second-Phase Resin Structure on the Interfacial Shear Strength of Carbon Fiber/Epoxy Resin
The toughening modification of epoxy resin has received widespread attention. The addition of the second-phase resin has a good toughening effect on epoxy resin. In order to investigate the effect of the second-phase resin on the interphase of composites, in this work the interfacial properties of carbon fiber (CF)/epoxy resin with the second-phase resin structure were investigated. Methodologies including surface structure observation, chemical characteristics, surface energy of the CF, and micro-phase structure characterization of resin were tested, followed by the micro-interfacial performance of CF/epoxy composites before and after hygrothermal treatment. The results revealed that the sizing process has the positive effect of increasing the interfacial bonding properties of CF/epoxy. From the interfacial shear strength (IFSS) test, the introduction of the second phase in the resin reduced the interfacial bonding performance between the CF and epoxy. After the hygrothermal treatment, water molecules diffused along the interfacial paths between the two resins, which in turn created defects and consequently brought about a reduction in the IFSS.
- Open Access
Micro-Structure and Dielectric Properties of Ti3C2Tx MXene after Annealing Treatment under Inert Gases
At present, the rapid development of electronic devices such as batteries, sensors, capacitors and so on is creating a huge demand for lightweight materials with a designed structure and function. Ti3C2Tx MXene, a lightweight two-dimensional (2D) nanomaterial with excellent electronic properties, has been favored in this field. In this work, Ti3C2Tx MXene was annealed under an inert gas (N2, Ar and CO2) atmosphere to design the crystal structure and interface of the nanosheets, and then the modified nanosheets with specific changes in dielectric properties were obtained. Among them, the key temperature points (100 °C, 300 °C, 500 °C and 800 °C) in the thermogravimetric (TG) test under an air atmosphere were used as the annealing temperature. When annealing under an air atmosphere, with the increase in temperature, the Ti layer gradually oxidized and evaporated, and the original two-dimensional structure was partly destroyed with some of the C atoms reacting with O2 to form CO2. In the inert gas atmosphere, however, the 2D structure is preserved, except that the surface end groups and layer spacing are changed. In addition, some N element doping was introduced into the nanosheets after N2 atmosphere treatment, which changed the original lattice structure. After the Ar atmosphere treatment, some Ti atoms on the surface were oxidized in situ to form TiO2 grains with different crystal forms, which increased the interfacial area. The C-TiO2 structure of the nanosheets was more complete after treatment with the CO2 atmosphere. All the nanosheets after heat treatment with an inert gas atmosphere retained the characteristic morphology of 2D materials, and different changes in the micro-structure caused changes in dielectric properties, thereby meeting the needs of 2D nanomaterials Ti3C2Tx MXene in different scenarios.
Open AccessMicro-Structure and Dielectric Properties of Ti3C2Tx MXene after Annealing Treatment under Inert Gases
At present, the rapid development of electronic devices such as batteries, sensors, capacitors and so on is creating a huge demand for lightweight materials with a designed structure and function. Ti3C2Tx MXene, a lightweight two-dimensional (2D) nanomaterial with excellent electronic properties, has been favored in this field. In this work, Ti3C2Tx MXene was annealed under an inert gas (N2, Ar and CO2) atmosphere to design the crystal structure and interface of the nanosheets, and then the modified nanosheets with specific changes in dielectric properties were obtained. Among them, the key temperature points (100 °C, 300 °C, 500 °C and 800 °C) in the thermogravimetric (TG) test under an air atmosphere were used as the annealing temperature. When annealing under an air atmosphere, with the increase in temperature, the Ti layer gradually oxidized and evaporated, and the original two-dimensional structure was partly destroyed with some of the C atoms reacting with O2 to form CO2. In the inert gas atmosphere, however, the 2D structure is preserved, except that the surface end groups and layer spacing are changed. In addition, some N element doping was introduced into the nanosheets after N2 atmosphere treatment, which changed the original lattice structure. After the Ar atmosphere treatment, some Ti atoms on the surface were oxidized in situ to form TiO2 grains with different crystal forms, which increased the interfacial area. The C-TiO2 structure of the nanosheets was more complete after treatment with the CO2 atmosphere. All the nanosheets after heat treatment with an inert gas atmosphere retained the characteristic morphology of 2D materials, and different changes in the micro-structure caused changes in dielectric properties, thereby meeting the needs of 2D nanomaterials Ti3C2Tx MXene in different scenarios.