Alina Mustatea
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alina Mustatea has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Bogdan Trica
National Institute for Research & Development in Chemistry and Petrochemistry—ICECHIM Bucharest, 202 Splaiul Independenței, 060021 Bucharest, Romania
2 shared publications - Doina Dimonie
Faculty of Chemical Engineering and Biotechnologies-Doctoral School, National University of Science and Technology POLITEHNICA, 011061 Bucharest, Romania
2 shared publications - Cristian Andi Nicolae
National Institute for Research & Development in Chemistry and Petrochemistry—ICECHIM, 202 Splaiul Independentei, 060021 Bucharest, Romania
1 shared publication - Florentina Miu
PROMATERIS SA, Bucharest-Targoviste Street, no.1, 070000 Buftea, Romania
1 shared publication - Florentina Monica Raduly
National Institute for Research & Development in Chemistry and Petrochemistry—ICECHIM, 202 Splaiul Independentei, 060021 Bucharest, Romania
1 shared publication - Laurentiu Soare
PROMATERIS SA, Bucharest-Targoviste Street, no.1, 070000 Buftea, Romania
1 shared publication
Latest Publications
- Open Access
- 31 August 2023
- Published by MDPI AG in Chemistry Proceedings
- Vol. 13 (1) , 4
XRD Studies of the Morphological Changes Generated by Interface Agents for Obtaining New Scalable Sustainable Blends Based on Starch and PCL
The starch–PCL blends are important from a practical point of view. Due to the hydrophobic nature of PCL, its blends with starch are immiscible. Therefore, these blends must be compatibilized to control the interface’s properties and the thermodynamic stability over time. A physical compatibilization solution, easier to scale up in industrial conditions, was attempted. The results showed better compatibility between the two tested polymers because of the grafted olefin polymer that eliminates the net difference between the in-contact phases, by creating an interface area, strengthening the multicomponent system and reducing the morphological defects as voids.
- 31 August 2023
- Published by MDPI AG in Chemistry Proceedings
- Vol. 13 (1) , 4
Open AccessXRD Studies of the Morphological Changes Generated by Interface Agents for Obtaining New Scalable Sustainable Blends Based on Starch and PCL
The starch–PCL blends are important from a practical point of view. Due to the hydrophobic nature of PCL, its blends with starch are immiscible. Therefore, these blends must be compatibilized to control the interface’s properties and the thermodynamic stability over time. A physical compatibilization solution, easier to scale up in industrial conditions, was attempted. The results showed better compatibility between the two tested polymers because of the grafted olefin polymer that eliminates the net difference between the in-contact phases, by creating an interface area, strengthening the multicomponent system and reducing the morphological defects as voids.
- Open Access
New Biodegradable Materials for Re-Thought Packaging from Pre-Consumer Wastes by Controlling the Storage Time as Method to Increase the Mechanical Recycling Efficiency
The influence of storage conditions on the mechanical recycling of pre-consumer waste (PRE-CW) from the manufacture of multilayer packaging films starting from starch compounds using a renewable-based polymer with PCL and PBAT, which are biodegradable conventional-based polyesters, was studied. It was found that, unlike materials based on conventional-origin polymers that accumulate in the environment for hundreds of years, the studied compounds degraded, even in the solid state, duringstorage in unventilated spaces and during the rainy hot summers with alternatingheat and rain. The degradation of the mechanically recycled compounds obtained from PRE-CW stored in such conditions was highlighted by the comparative analysis with the primary compounds, which proved the following: specific FTIR spectra changes; 2–3-times higher melt fluidity than for primary compounds; melting in successive processes over the entire positive temperatures range, up to 115 °C, such as in cases of compositional de-mixing of incompatible blends, faced to a single melting endotherm with a maximum at around 120 °C for the primar thermal degradation with the movement of the main destruction stages towards higher temperatures; a high quantity residue at 750 °C in air; dispersed mechanical resistance properties y compounds; crystallization at temperatures 10 °C–15 °C higher. The elimination of storage before the mechanical recycling of the pre-consumer waste from this type of polymeric compound fabrication is a way to increase the mechanical recycling efficiency while obtaining new materials with functional properties required by the applications.
Open AccessNew Biodegradable Materials for Re-Thought Packaging from Pre-Consumer Wastes by Controlling the Storage Time as Method to Increase the Mechanical Recycling Efficiency
The influence of storage conditions on the mechanical recycling of pre-consumer waste (PRE-CW) from the manufacture of multilayer packaging films starting from starch compounds using a renewable-based polymer with PCL and PBAT, which are biodegradable conventional-based polyesters, was studied. It was found that, unlike materials based on conventional-origin polymers that accumulate in the environment for hundreds of years, the studied compounds degraded, even in the solid state, duringstorage in unventilated spaces and during the rainy hot summers with alternatingheat and rain. The degradation of the mechanically recycled compounds obtained from PRE-CW stored in such conditions was highlighted by the comparative analysis with the primary compounds, which proved the following: specific FTIR spectra changes; 2–3-times higher melt fluidity than for primary compounds; melting in successive processes over the entire positive temperatures range, up to 115 °C, such as in cases of compositional de-mixing of incompatible blends, faced to a single melting endotherm with a maximum at around 120 °C for the primar thermal degradation with the movement of the main destruction stages towards higher temperatures; a high quantity residue at 750 °C in air; dispersed mechanical resistance properties y compounds; crystallization at temperatures 10 °C–15 °C higher. The elimination of storage before the mechanical recycling of the pre-consumer waste from this type of polymeric compound fabrication is a way to increase the mechanical recycling efficiency while obtaining new materials with functional properties required by the applications.