Youhuan Ning
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Youhuan Ning has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Zhen Tian
Space Control and Inertial Technology Research Center, Harbin Institute of Technology, Harbin, China
5 shared publications - Wei Cheng
Space Control and Inertial Technology Research Center, Harbin Institute of Technology, Harbin, China
4 shared publications - Boqi Xi
Space Control and Inertial Technology Research Center, Harbin Institute of Technology, Harbin, China
3 shared publications Changhong Wang
3 shared publications- Changhong Wang
Space Control and Inertial Technology Research Center, Harbin Institute of Technology, Harbin, China
3 shared publications Zhen Tian
3 shared publications
Latest Publications
- 16 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 1-12
Modeling, Decoupling Identification, and Compensation of Imbalance Errors for Whole-Angle Hemispherical Resonator Gyroscopes
This paper developed a comprehensive error model for whole-angle hemispherical resonator gyroscopes (WA HRGs) based on an analysis of their fundamental structure and operating principles. This model elucidates the evolution rules of resonators' anisotropy, gain coupling errors, and phase errors, as well as the impact mechanism of their coupling effects on the performance of HRG. According to the analytical results of the model, a novel method for decoupling, identifying, and compensating errors was proposed. First, in the mode where only orthogonal control force was applied, decoupling and compensation for detection gain mis-match were achieved by analyzing the distribution characteristics of the ratio between vibration energy and its change rate in the control loop with respect to azimuth. Second, the excitation gain mismatch and phase error were identified and compensated by in-jecting a sinusoidal signal into the virtual precession loop, based on the coupling between the quadrature control force, amplitude control force, and virtual Coriolis force. Finally, damping anisot-ropy was identified and compensated for by analyzing the distri-bution characteristics of the amplitude control force with respect to angle. The effectiveness of the error model and calibration method was verified by simulation and experimentation. The re-sult indicates that after error compensation, the angular rate har-monic error decreased from 0.0375°/s to 0.0051°/s, the scaling fac-tor nonlinearity decreased from 7.465 ppm to 1.131 ppm, and the bias instability (BI) improved from 0.0560°/h to 0.0096°/h, signifi-cantly improving the gyroscope's performance.
- 16 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 75 (00189456) , 1-12
Modeling, Decoupling Identification, and Compensation of Imbalance Errors for Whole-Angle Hemispherical Resonator Gyroscopes
This paper developed a comprehensive error model for whole-angle hemispherical resonator gyroscopes (WA HRGs) based on an analysis of their fundamental structure and operating principles. This model elucidates the evolution rules of resonators' anisotropy, gain coupling errors, and phase errors, as well as the impact mechanism of their coupling effects on the performance of HRG. According to the analytical results of the model, a novel method for decoupling, identifying, and compensating errors was proposed. First, in the mode where only orthogonal control force was applied, decoupling and compensation for detection gain mis-match were achieved by analyzing the distribution characteristics of the ratio between vibration energy and its change rate in the control loop with respect to azimuth. Second, the excitation gain mismatch and phase error were identified and compensated by in-jecting a sinusoidal signal into the virtual precession loop, based on the coupling between the quadrature control force, amplitude control force, and virtual Coriolis force. Finally, damping anisot-ropy was identified and compensated for by analyzing the distri-bution characteristics of the amplitude control force with respect to angle. The effectiveness of the error model and calibration method was verified by simulation and experimentation. The re-sult indicates that after error compensation, the angular rate har-monic error decreased from 0.0375°/s to 0.0051°/s, the scaling fac-tor nonlinearity decreased from 7.465 ppm to 1.131 ppm, and the bias instability (BI) improved from 0.0560°/h to 0.0096°/h, signifi-cantly improving the gyroscope's performance.
- 5 July 2025
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 302
Trimming of the unbalanced mass in resonators with ion beams
- 5 July 2025
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 302
Trimming of the unbalanced mass in resonators with ion beams
- 30 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (13) , 23899-23912
Dynamic Modeling and Coupling Error Analysis of Imperfect Hemispherical Resonators
Hemispherical Resonator Gyroscope (HRG) represents a new type of inertial sensor. The vibrational properties of the hemispherical resonator, a core component of the HRG, significantly influence the output accuracy of the gyroscope. This paper is the first to integrate the effects of residual stress nonuniformity and mass nonuniformity in a unified model for hemispherical resonator. Firstly, the equation of motion for the resonator with these nonuniformities are derived based on the thin shell theory and the Lagrange equation. Then, two important vibration parameters, including the frequency split and the azimuth of stiffness axis, are calculated by a novel method based on the unified model. Next, the detailed simulations are conducted, which reveals that the frequency split is directly proportional to the fourth harmonic magnitude of mass or residual stress nonuniformity alone, with the azimuth of stiffness axis aligning with their initial phase (or differing by 22.5° for shear stress). However, under coupled nonuniformities, the frequency split depends nonlinearly on both fourth harmonics, while the azimuth of stiffness axis exhibits complex nonlinear behavior, with coupling strength critically influenced by their phase difference. Finally, based on the least squares method, an identification scheme for the error parameters associated with residual stress nonuniformity is designed. The experimental results show good consistency with the theoretical predictions, which confirms the correctness of the dynamic model and error analysis. This study addresses practical limitations of existing models and provides a theoretical foundation and experimental guidance for the optimization of the manufacturing processes of high-precision HRG.
- 30 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (13) , 23899-23912
Dynamic Modeling and Coupling Error Analysis of Imperfect Hemispherical Resonators
Hemispherical Resonator Gyroscope (HRG) represents a new type of inertial sensor. The vibrational properties of the hemispherical resonator, a core component of the HRG, significantly influence the output accuracy of the gyroscope. This paper is the first to integrate the effects of residual stress nonuniformity and mass nonuniformity in a unified model for hemispherical resonator. Firstly, the equation of motion for the resonator with these nonuniformities are derived based on the thin shell theory and the Lagrange equation. Then, two important vibration parameters, including the frequency split and the azimuth of stiffness axis, are calculated by a novel method based on the unified model. Next, the detailed simulations are conducted, which reveals that the frequency split is directly proportional to the fourth harmonic magnitude of mass or residual stress nonuniformity alone, with the azimuth of stiffness axis aligning with their initial phase (or differing by 22.5° for shear stress). However, under coupled nonuniformities, the frequency split depends nonlinearly on both fourth harmonics, while the azimuth of stiffness axis exhibits complex nonlinear behavior, with coupling strength critically influenced by their phase difference. Finally, based on the least squares method, an identification scheme for the error parameters associated with residual stress nonuniformity is designed. The experimental results show good consistency with the theoretical predictions, which confirms the correctness of the dynamic model and error analysis. This study addresses practical limitations of existing models and provides a theoretical foundation and experimental guidance for the optimization of the manufacturing processes of high-precision HRG.
- 28 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (13) , 23888-23898
Suppression and Compensation of Damping Asymmetry Errors in Whole-Angle Hemispherical Resonator Gyroscope
This paper studied the primary sources, evolution rules, and influence mechanisms of the damping anisotropy of the whole-angle hemispherical resonator gyroscope from the perspective of the fabrication process and analyzed the influence of temperature change on the damping anisotropy. An error identification and compensation method is proposed to suppress the effect of the damping anisotropy error on the gyroscope's bias error. According to the energy controller's output, this method involves applying the recursive least squares method to identify the damping anisotropy error and the damping axis angle in real time. Subsequently, a compensation signal is synthesized based on the identification results and applied to the angular rate control loop to compensate for the damping asymmetry error online. The experimental results show that the peak-to-peak value of the angular rate output harmonic error of the gyroscope is reduced from 0.023°/s to 0.005°/s after the error compensation, which is an improvement of about 5 times. In addition, the peak-to-peak value of the gyroscope angular dependent bias error decreases from 0.7072° to 0.08268°, which improves by 8.55 times, and the linearity of the angular measurements is also significantly improved. This methodology can be widely applied to gyroscopes operating in whole-angle mode, which is essential for fundamentally reducing the bias errors of the gyroscope induced by damping asymmetry.
- 28 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (13) , 23888-23898
Suppression and Compensation of Damping Asymmetry Errors in Whole-Angle Hemispherical Resonator Gyroscope
This paper studied the primary sources, evolution rules, and influence mechanisms of the damping anisotropy of the whole-angle hemispherical resonator gyroscope from the perspective of the fabrication process and analyzed the influence of temperature change on the damping anisotropy. An error identification and compensation method is proposed to suppress the effect of the damping anisotropy error on the gyroscope's bias error. According to the energy controller's output, this method involves applying the recursive least squares method to identify the damping anisotropy error and the damping axis angle in real time. Subsequently, a compensation signal is synthesized based on the identification results and applied to the angular rate control loop to compensate for the damping asymmetry error online. The experimental results show that the peak-to-peak value of the angular rate output harmonic error of the gyroscope is reduced from 0.023°/s to 0.005°/s after the error compensation, which is an improvement of about 5 times. In addition, the peak-to-peak value of the gyroscope angular dependent bias error decreases from 0.7072° to 0.08268°, which improves by 8.55 times, and the linearity of the angular measurements is also significantly improved. This methodology can be widely applied to gyroscopes operating in whole-angle mode, which is essential for fundamentally reducing the bias errors of the gyroscope induced by damping asymmetry.
- 3 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-12
Analysis, Identification, and Compensation of Damping Asymmetry for Whole-Angle Mode Hemispherical Resonator Gyro
This article studies a parameter identification and compensation method to improve the effect of damping asymmetry for the whole-angle mode hemispherical resonator gyro. First, the reason for damping asymmetry is analyzed from the process point of view and a motion equation containing the damping asymmetry is established based on the existing formulas. This sets the foundation for the subsequent analysis and compensation. Second, the equations of gyro drift are derived to clarify the effect of damping asymmetry on the standing wave parameters and key control indicators. The relationship between the output angular rate fluctuation and the damping asymmetry is also obtained. Third, a method of parameter identification and compensation is proposed based on the similarity of the angular rate compensation force and the harmonic components of the amplitude control force. The feasibility of the method is proved in simulation. Finally, the experimental results show that after compensation, the output angular rate fluctuation range is reduced to 29.77% of that before compensation, and the scale factor nonlinearity is dramatically decreased by about 7 times from 103.629 ppm to 15.063 ppm, significantly improving the hemispherical resonator gyro’s performance. Besides, the experiments prove that the effect of mode-matching errors and quadrature errors on the compensation method is extremely limited, verifying the reliability of the method.
- 3 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-12
Analysis, Identification, and Compensation of Damping Asymmetry for Whole-Angle Mode Hemispherical Resonator Gyro
This article studies a parameter identification and compensation method to improve the effect of damping asymmetry for the whole-angle mode hemispherical resonator gyro. First, the reason for damping asymmetry is analyzed from the process point of view and a motion equation containing the damping asymmetry is established based on the existing formulas. This sets the foundation for the subsequent analysis and compensation. Second, the equations of gyro drift are derived to clarify the effect of damping asymmetry on the standing wave parameters and key control indicators. The relationship between the output angular rate fluctuation and the damping asymmetry is also obtained. Third, a method of parameter identification and compensation is proposed based on the similarity of the angular rate compensation force and the harmonic components of the amplitude control force. The feasibility of the method is proved in simulation. Finally, the experimental results show that after compensation, the output angular rate fluctuation range is reduced to 29.77% of that before compensation, and the scale factor nonlinearity is dramatically decreased by about 7 times from 103.629 ppm to 15.063 ppm, significantly improving the hemispherical resonator gyro’s performance. Besides, the experiments prove that the effect of mode-matching errors and quadrature errors on the compensation method is extremely limited, verifying the reliability of the method.
- 22 May 2024
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 277
Anchor loss improvement in hemispherical resonators with ion beams
- 22 May 2024
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 277
Anchor loss improvement in hemispherical resonators with ion beams
- 12 August 2023
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 261
Frequency splitting of hemispherical resonators trimmed with focused ion beams
- 12 August 2023
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 261
Frequency splitting of hemispherical resonators trimmed with focused ion beams