DLDong Li

Dong Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dong Li has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Effect of Porosity on the Corrosion Behavior of FeCoNiMnCrx Porous High-Entropy Alloy in 3.5 Wt.% NaCl Solution

    by Ying Wang, Shuobin Chen, Yuhua Peng, Xijie Zheng, Dong Li, Cheng Nie, Pan Gong, Zhigang Hu, Ming Ma

    The effects of different Cr contents on the corrosion resistance of FeCoNiMnCrx (x = 0.5;1;1.5) porous high-entropy alloys (HEAs) in 3.5 wt.% NaCl solution on corrosion resistance was investigated. With the increase in Cr content, the total porosity and permeability of the porous HEA increased. The increase in porosity improves the interconnectivity between the pores and enhances the contact area with the corrosion solution. The pore-making mechanism is mainly a powder compaction, and Kirkendall holes are caused by different elements due to different diffusion rates. With the increase in Cr content, the icorr increases, and the Ecorr decreases in the porous HEAs of FeCoNiMnCrx (x = 0.5;1;1.5). The corrosion resistance of FeCoNiMnCrx (x = 0.5;1;1.5) porous HEAs decreases with the increase in the Cr element. With the increase in Cr content, the weight gain rate of FeCoNiMnCrx porous HEA increases gradually after immersion for 168 h, and the average pore size and permeability of the sample decrease gradually. The corrosion resistance of FeCoNiMnCrx porous HEA decreases with increasing Cr content.


  • Open Access

    Research Progress on the Wear Resistance of Key Components in Agricultural Machinery

    by Ying Wang, Dong Li, Cheng Nie, Pan Gong, Junsheng Yang, Zhigang Hu, Bin Li, Ming Ma

    Agricultural mechanization is crucial in enhancing production efficiency, alleviating labor demands, reducing costs, improving agricultural product quality, and promoting sustainable development. However, wear and tear are inevitable when using agricultural machinery. The failure of critical wear-resistant parts is responsible for over 50% of rural machinery breakdowns. For instance, a domestic combine harvester typically only operates trouble-free for 20 to 30 h, and the service life of a rotary plow knife is approximately 80 h. Investigating the wear performance of key farm machinery components reinforces machinery design and maintenance strategies, extends machinery lifespans, enhances agricultural production efficiency, and advances agrarian sustainability. This paper provides a comprehensive overview of the latest research on the wear resistance of crucial agricultural machinery components. It delves into the factors influencing the wear resistance of these components and explores current effective measures to address wear-related issues. Additionally, it also summarizes the challenges and opportunities in researching the wear performance of key components in agricultural machinery and future development directions.


  • Open Access

    Effect of Grain Size on the Tribological Behavior of CoCrFeMnNi High Entropy Alloy

    by Ying Wang, Dong Li, Junsheng Yang, Junsong Jin, Mao Zhang, Xinyun Wang, Bin Li, Zhigang Hu, Pan Gong

    The effect and mechanism of grain sizes on the tribological behavior of CoCrFeMnNi high entropy alloy (HEA) were studied by friction experiments and wear morphology analysis. Under normal low load and low sliding speed, the primary wear mechanism of the HEA samples is adhesive wear. With the increase in sliding speed, the wear mechanisms of the samples are adhesive wear and oxidation wear. The oxide layer formed under the action of friction heat of the coarse grain (CG) sample is easy to break due to the softening of the CG. With the increase of normal load and sliding speed, the wear mechanisms of the HEA samples are mainly adhesive wear, oxidation wear, and plastic deformation. The oxide layer of CG sample has many cracks, and the worn surface also has plastic deformation, which leads to the increase of friction coefficient and specific wear rate and the decrease of wear resistance. Therefore, the fine grain size HEA sample has better wear resistance than the CG sample due to its high surface strength.