Torsten Clemens
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Torsten Clemens has a total of 86 co-authors. Here are the top co-authors by number of shared publications:
- Rafael E. Hincapie
OMV Exploration & Production GmbH, 1020 Vienna, Austria
12 shared publications - Muhammad Tahir
OMV Exploration & Production GmbH, 1020 Vienna, Austria
8 shared publications - Ante Borovina
OMV Exploration and Production GmbH, 1020 Vienna, Austria
5 shared publications - Maria-Magdalena Chiotoroiu
OMV Exploration & Production GmbH
5 shared publications - Mukul Mani Sharma
The University of Texas at Austin
4 shared publications - Amir Farzaneh
OMV Exploration & Production GmbH, 1020 Vienna, Austria
3 shared publications
Latest Publications
- Open Access
Produced-Fluid Analytics and Polymer Response During Alkali–Polymer Flooding After Polymer Flooding: Laboratory and Field Observations
Alkali–polymer (AP) flooding is a complex enhanced oil recovery (EOR) technique whose performance depends on reservoir mineralogy, crude oil properties, and formation water chemistry. The interactions among these factors can result in inconsistent field performance and make reliable prediction of AP breakthrough a key challenge for commercial applications. Accurate identification of breakthrough is particularly important because it directly influences operational decisions, including inhibitor dosing and production optimization. This study investigates the limitations of using pH as a standalone breakthrough indicator and proposes a multi-parameter analytical approach incorporating divalent cation concentrations, polymer concentration, alkalinity, and ammonia generation. As part of an Austrian AP flooding pilot project, laboratory core-flooding experiments were conducted under representative reservoir conditions. Two-phase flooding experiments were performed using 30-cm-long crude-oil-saturated core samples. The cores were sequentially injected with polymer and AP solutions to simulate field operations. Effluent samples were analyzed for iodide tracer concentration, sodium, calcium, magnesium, pH, alkalinity, ammonia, and polymer concentration. To evaluate the reproducibility of the results, duplicate experiments were conducted. In addition, a third experiment without polymer pre-flushing was performed to isolate AP breakthrough behavior. Field production data were subsequently analyzed to validate the laboratory observations. The results demonstrate that pH alone is insufficient for reliable assessment of AP breakthrough. Polymer concentrations in the effluent reached up to 1.9 times the injected concentration following AP injection into polymer-preconditioned cores, suggesting release of polymer retained during the preceding polymer flood. Alkali-induced desorption is considered a plausible mechanism; however, the present experiments do not independently distinguish desorption from other retention-release mechanisms. The laboratory experiments showed reproducible analytical response sequences, with Ca2+ decline preceding the main pH response under the investigated conditions. Comparison with selected pilot data showed qualitative consistency in the relative sequence of the principal indicators, although absolute timing differed between laboratory and field scales. The results support a multi-parameter framework for interpreting AP breakthrough while highlighting the limitations of using pH as a standalone indicator.
Open AccessProduced-Fluid Analytics and Polymer Response During Alkali–Polymer Flooding After Polymer Flooding: Laboratory and Field Observations
Alkali–polymer (AP) flooding is a complex enhanced oil recovery (EOR) technique whose performance depends on reservoir mineralogy, crude oil properties, and formation water chemistry. The interactions among these factors can result in inconsistent field performance and make reliable prediction of AP breakthrough a key challenge for commercial applications. Accurate identification of breakthrough is particularly important because it directly influences operational decisions, including inhibitor dosing and production optimization. This study investigates the limitations of using pH as a standalone breakthrough indicator and proposes a multi-parameter analytical approach incorporating divalent cation concentrations, polymer concentration, alkalinity, and ammonia generation. As part of an Austrian AP flooding pilot project, laboratory core-flooding experiments were conducted under representative reservoir conditions. Two-phase flooding experiments were performed using 30-cm-long crude-oil-saturated core samples. The cores were sequentially injected with polymer and AP solutions to simulate field operations. Effluent samples were analyzed for iodide tracer concentration, sodium, calcium, magnesium, pH, alkalinity, ammonia, and polymer concentration. To evaluate the reproducibility of the results, duplicate experiments were conducted. In addition, a third experiment without polymer pre-flushing was performed to isolate AP breakthrough behavior. Field production data were subsequently analyzed to validate the laboratory observations. The results demonstrate that pH alone is insufficient for reliable assessment of AP breakthrough. Polymer concentrations in the effluent reached up to 1.9 times the injected concentration following AP injection into polymer-preconditioned cores, suggesting release of polymer retained during the preceding polymer flood. Alkali-induced desorption is considered a plausible mechanism; however, the present experiments do not independently distinguish desorption from other retention-release mechanisms. The laboratory experiments showed reproducible analytical response sequences, with Ca2+ decline preceding the main pH response under the investigated conditions. Comparison with selected pilot data showed qualitative consistency in the relative sequence of the principal indicators, although absolute timing differed between laboratory and field scales. The results support a multi-parameter framework for interpreting AP breakthrough while highlighting the limitations of using pH as a standalone indicator.
- 14 September 2026
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 31 (11) , 7992-8009
Effects of Alkali on Polymer Propagation and Viscosity Retention in Porous Media: Insights From Coreflooding Experiments
Summary: Adsorption of alkali on rock surfaces is a well-established phenomenon in high total acid number (TAN) oil reservoirs, particularly noticeable during alkali-polymer (AP) flooding. Despite this, the influence of alkali on the degradation of polymers in these environments remains insufficiently understood. This study explores the role of alkali in enhancing the viscosity stability of polymers under shear stress conditions prevalent in porous media. Utilizing polyacrylamide polymer products supplied by two vendors, AP slugs were prepared for this work. Coreflooding experiments were conducted at injection velocities representative of field-scale operations to induce and study the degradation of polymer chains. These experiments were enabled to assess the rate of polymer degradation, for which viscosity measurements served as a primary metric. To encompass a range of field scenarios, injection velocities varied from 1 ft/day to 20 ft/day. Additionally, core plugs with both low and high permeability were used to replicate the diverse shear rates encountered in heterogeneous reservoirs. Our findings demonstrate that AP slugs exhibited lower viscosity loss during core flow, resulting from a combined effect of brine softening, reduced adsorption, and chemical aging at high pH. These changes are likely attributed to the increased anionicity caused by alkali. Another contributor could be the role of alkali as changing rock surfaces to be positively charged, which seems to reduce polymer adsorption, thereby helping to maintain the viscosity of the produced polymer solutions. Core plugs with lower permeability exhibited higher shear rates, leading to a marginally greater breakdown of polymer chains and consequently more significant viscosity reduction in effluents. As anticipated, higher injection velocities, which simulate the conditions near wells, resulted in greater viscosity losses. In comparing the two polymer products, the product from Vendor B showed superior viscosity control, whereas the product from Vendor A exhibited enhanced propagation in porous media. The injectivity outcomes for corefloods in the presence of crude oil (two-phase) align with those from single-phase corefloods when injecting polymer/AP slugs. The reported viscosity behavior reflects the combined effects of chemical aging, brine composition, and flow-induced stresses, and should not be interpreted as a direct measure of mechanical degradation. The enhanced recovery factor attributed to the AP slug injection (23% vs. 2%) is confirmed to the result not only from the in-situ saponification process but also from the increased viscosity retention of the AP slug. This study not only sheds light on the flow dynamics of polyacrylamide polymers but also underscores the importance of viscosity retention in situ. Such stability is a critical factor affecting both injectivity and mobility in porous media. Therefore, it is imperative to consider these findings as part of the screening criteria for field applications, especially where AP flooding is used. This research thus provides a pivotal step forward in understanding and optimizing polymer-based enhanced oil recovery (EOR) techniques in challenging reservoir conditions.
- 14 September 2026
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 31 (11) , 7992-8009
Effects of Alkali on Polymer Propagation and Viscosity Retention in Porous Media: Insights From Coreflooding Experiments
Summary: Adsorption of alkali on rock surfaces is a well-established phenomenon in high total acid number (TAN) oil reservoirs, particularly noticeable during alkali-polymer (AP) flooding. Despite this, the influence of alkali on the degradation of polymers in these environments remains insufficiently understood. This study explores the role of alkali in enhancing the viscosity stability of polymers under shear stress conditions prevalent in porous media. Utilizing polyacrylamide polymer products supplied by two vendors, AP slugs were prepared for this work. Coreflooding experiments were conducted at injection velocities representative of field-scale operations to induce and study the degradation of polymer chains. These experiments were enabled to assess the rate of polymer degradation, for which viscosity measurements served as a primary metric. To encompass a range of field scenarios, injection velocities varied from 1 ft/day to 20 ft/day. Additionally, core plugs with both low and high permeability were used to replicate the diverse shear rates encountered in heterogeneous reservoirs. Our findings demonstrate that AP slugs exhibited lower viscosity loss during core flow, resulting from a combined effect of brine softening, reduced adsorption, and chemical aging at high pH. These changes are likely attributed to the increased anionicity caused by alkali. Another contributor could be the role of alkali as changing rock surfaces to be positively charged, which seems to reduce polymer adsorption, thereby helping to maintain the viscosity of the produced polymer solutions. Core plugs with lower permeability exhibited higher shear rates, leading to a marginally greater breakdown of polymer chains and consequently more significant viscosity reduction in effluents. As anticipated, higher injection velocities, which simulate the conditions near wells, resulted in greater viscosity losses. In comparing the two polymer products, the product from Vendor B showed superior viscosity control, whereas the product from Vendor A exhibited enhanced propagation in porous media. The injectivity outcomes for corefloods in the presence of crude oil (two-phase) align with those from single-phase corefloods when injecting polymer/AP slugs. The reported viscosity behavior reflects the combined effects of chemical aging, brine composition, and flow-induced stresses, and should not be interpreted as a direct measure of mechanical degradation. The enhanced recovery factor attributed to the AP slug injection (23% vs. 2%) is confirmed to the result not only from the in-situ saponification process but also from the increased viscosity retention of the AP slug. This study not only sheds light on the flow dynamics of polyacrylamide polymers but also underscores the importance of viscosity retention in situ. Such stability is a critical factor affecting both injectivity and mobility in porous media. Therefore, it is imperative to consider these findings as part of the screening criteria for field applications, especially where AP flooding is used. This research thus provides a pivotal step forward in understanding and optimizing polymer-based enhanced oil recovery (EOR) techniques in challenging reservoir conditions.
- 31 March 2026
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 31 (06) , 4106-4130
Performance of Inflow Control Devices in Horizontal Injection Wells with Injection-Induced Fractures
Summary: Inflow control devices (ICDs) have become important tools in managing the injection profile of wells. Their design is typically based on the initial condition of each injection zone. This paper, inspired by a Middle East offshore field study, explores the interaction between the ICD design and placement in horizontal injectors and how their performance is affected by the initiation and propagation of injection-induced fractures (IIFs) during the reservoir’s dynamic evolution. We use an advanced fully coupled reservoir-fracture-wellbore simulator that integrates ICD pressure drop modeling with dynamic IIF propagation under thermal and porous elastic stresses. This allows us to systematically investigate, for the first time, not only how ICDs redistribute injection flow, but also how IIFs alter ICD performance over time. This simulator integrates wellbore dynamics with ICD functionality, multiphase flow in the reservoir, solid mechanics, and energy balance, allowing for thermally induced fracture propagation and particle plugging. It accounts for the thermoporoelastic effects in the stress field during cold water injection, simulating fracture initiation and propagation driven by both internal and external filtration as well as thermal effects. The pressure drop across the ICDs is solved within a fully coupled nonlinear system of equations using the Newton-Raphson (NR) method, enabling the prediction of fracture initiation and growth at various sections of the well over time. The model allows us to assess the impact of ICD placement and characteristics on the long-term injection profile in the well. The model was validated through history matching field data and demonstrates that ICD placement and specifications can significantly influence long-term injection profiles. To demonstrate the impact of IIFs, we first focus on model results for a homogeneous reservoir setup. The setup is intentionally used as a benchmark, providing a unit-test style validation before extending the model to heterogeneous reservoirs. This avoids the complex effects associated with reservoir heterogeneity and clearly demonstrates important ICD-IIF interactions. The results indicate that the growth of IIFs significantly impacts ICD performance and governs the injection flow profile. In the absence of ICDs, the flow distribution can vary considerably over time due to the development of IIFs. Injector performance is analyzed for different ICD configurations, demonstrating that ICDs can effectively regulate flow distribution along the wellbore, enhancing conformance control even when fractures start and propagate. When designed appropriately, ICDs can mitigate the impact of potentially problematic “thief” fractured zones. Although ICDs introduce an additional pressure drop that may reduce injectivity, they promote a more uniform flow distribution, which can slow the decline in injectivity and improve reservoir sweep and oil recovery. Our findings suggest that, in many instances, optimizing the placement and specifications of ICDs can enhance the injection profile, leading to improved recovery rates and a reduced risk of out-of-zone fracture growth. Our results illustrate the dynamics of multiple fracture growth in segments of the injector wellbore separated by ICDs and their effect on flow distribution for the first time. These insights provide a foundation for the effective design and placement of ICDs in horizontal injectors.
- 31 March 2026
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 31 (06) , 4106-4130
Performance of Inflow Control Devices in Horizontal Injection Wells with Injection-Induced Fractures
Summary: Inflow control devices (ICDs) have become important tools in managing the injection profile of wells. Their design is typically based on the initial condition of each injection zone. This paper, inspired by a Middle East offshore field study, explores the interaction between the ICD design and placement in horizontal injectors and how their performance is affected by the initiation and propagation of injection-induced fractures (IIFs) during the reservoir’s dynamic evolution. We use an advanced fully coupled reservoir-fracture-wellbore simulator that integrates ICD pressure drop modeling with dynamic IIF propagation under thermal and porous elastic stresses. This allows us to systematically investigate, for the first time, not only how ICDs redistribute injection flow, but also how IIFs alter ICD performance over time. This simulator integrates wellbore dynamics with ICD functionality, multiphase flow in the reservoir, solid mechanics, and energy balance, allowing for thermally induced fracture propagation and particle plugging. It accounts for the thermoporoelastic effects in the stress field during cold water injection, simulating fracture initiation and propagation driven by both internal and external filtration as well as thermal effects. The pressure drop across the ICDs is solved within a fully coupled nonlinear system of equations using the Newton-Raphson (NR) method, enabling the prediction of fracture initiation and growth at various sections of the well over time. The model allows us to assess the impact of ICD placement and characteristics on the long-term injection profile in the well. The model was validated through history matching field data and demonstrates that ICD placement and specifications can significantly influence long-term injection profiles. To demonstrate the impact of IIFs, we first focus on model results for a homogeneous reservoir setup. The setup is intentionally used as a benchmark, providing a unit-test style validation before extending the model to heterogeneous reservoirs. This avoids the complex effects associated with reservoir heterogeneity and clearly demonstrates important ICD-IIF interactions. The results indicate that the growth of IIFs significantly impacts ICD performance and governs the injection flow profile. In the absence of ICDs, the flow distribution can vary considerably over time due to the development of IIFs. Injector performance is analyzed for different ICD configurations, demonstrating that ICDs can effectively regulate flow distribution along the wellbore, enhancing conformance control even when fractures start and propagate. When designed appropriately, ICDs can mitigate the impact of potentially problematic “thief” fractured zones. Although ICDs introduce an additional pressure drop that may reduce injectivity, they promote a more uniform flow distribution, which can slow the decline in injectivity and improve reservoir sweep and oil recovery. Our findings suggest that, in many instances, optimizing the placement and specifications of ICDs can enhance the injection profile, leading to improved recovery rates and a reduced risk of out-of-zone fracture growth. Our results illustrate the dynamics of multiple fracture growth in segments of the injector wellbore separated by ICDs and their effect on flow distribution for the first time. These insights provide a foundation for the effective design and placement of ICDs in horizontal injectors.
- 11 March 2026
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 31 (05) , 3440-3456
Alkali-Polymer Flooding after Polymer Flooding: Field Test Results
Summary: Polymer flooding has matured into a commercially viable enhanced oil recovery (EOR) method. Yet, substantial volumes of oil often remain trapped post-polymer injection, and economically feasible solutions for further recovery are limited—with no widely reported successful field implementations to date. With this study, we present field results from alkali-polymer (AP) injection following long-term polymer flooding. In this approach, alkali reacts with reactive crude oil to generate in-situ soaps that mobilize residual oil, while polymers maintain sweep efficiency and enhance microscopic displacement. The oil exhibited a total acid number (TAN) of 2.14 mg/L, indicating its high chemical reactivity with alkali. Before field implementation, a comprehensive laboratory program was conducted to optimize alkali and polymer selection, concentrations, and rheological properties—while addressing interactions with reservoir rock, near-wellbore area effects, geomechanics, and reservoir architecture. Scale inhibition strategies and water quality controls were also developed to mitigate operational risks. Initial field pilot results indicate that AP injection using the selected alkali and polymer achieves additional oil recovery, even after previous polymer flooding. The simplified chemistry of alkali and polymer compared with more complex alkali/surfactant/polymer (ASP) formulations reduces surface facility complexity and operating expenditures (OPEX). It should be noted that for AP flooding to be effective, sufficient soaps must be produced through the reaction of alkali with oil, and these soaps should not be overly hydrophobic, as this would prevent achieving low interfacial tension (IFT). Scaling was prevented in injection wells using softened water and managed in producer wells through targeted inhibitor dosing. Economic evaluation reveals that AP injection post-polymer flooding can achieve unit technical costs below EUR 30/bbl, with further cost reduction and performance optimization possible through chemical and operational refinement. Additionally, direct AP injection—without preceding polymer flooding—shows promise for oil reservoirs containing reactive oils, potentially leading to higher net present value (NPV) through higher incremental oil recovery and accelerated revenue realization compared with AP after polymer flooding.
- 11 March 2026
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 31 (05) , 3440-3456
Alkali-Polymer Flooding after Polymer Flooding: Field Test Results
Summary: Polymer flooding has matured into a commercially viable enhanced oil recovery (EOR) method. Yet, substantial volumes of oil often remain trapped post-polymer injection, and economically feasible solutions for further recovery are limited—with no widely reported successful field implementations to date. With this study, we present field results from alkali-polymer (AP) injection following long-term polymer flooding. In this approach, alkali reacts with reactive crude oil to generate in-situ soaps that mobilize residual oil, while polymers maintain sweep efficiency and enhance microscopic displacement. The oil exhibited a total acid number (TAN) of 2.14 mg/L, indicating its high chemical reactivity with alkali. Before field implementation, a comprehensive laboratory program was conducted to optimize alkali and polymer selection, concentrations, and rheological properties—while addressing interactions with reservoir rock, near-wellbore area effects, geomechanics, and reservoir architecture. Scale inhibition strategies and water quality controls were also developed to mitigate operational risks. Initial field pilot results indicate that AP injection using the selected alkali and polymer achieves additional oil recovery, even after previous polymer flooding. The simplified chemistry of alkali and polymer compared with more complex alkali/surfactant/polymer (ASP) formulations reduces surface facility complexity and operating expenditures (OPEX). It should be noted that for AP flooding to be effective, sufficient soaps must be produced through the reaction of alkali with oil, and these soaps should not be overly hydrophobic, as this would prevent achieving low interfacial tension (IFT). Scaling was prevented in injection wells using softened water and managed in producer wells through targeted inhibitor dosing. Economic evaluation reveals that AP injection post-polymer flooding can achieve unit technical costs below EUR 30/bbl, with further cost reduction and performance optimization possible through chemical and operational refinement. Additionally, direct AP injection—without preceding polymer flooding—shows promise for oil reservoirs containing reactive oils, potentially leading to higher net present value (NPV) through higher incremental oil recovery and accelerated revenue realization compared with AP after polymer flooding.
- Open Access
- 7 December 2025
- Published by Springer Nature in Geothermal Energy
- Vol. 13 (1)
Incorporating risk in geothermal field development planning: applying decision-theoretic agents
Geothermal field development requires decisions about data acquisition and the selection of an optimal development scenario (DS) under uncertainty. Effective planning must address two distinct types of risk: systematic risk, which affects the broader market, and unsystematic (idiosyncratic) risk, which is asset-specific. The inherent complexity of these decisions often leads to prolonged appraisal phases and suboptimal outcomes—particularly when it comes to incorporating risk into planning. This study applies decision-theoretic agents to assess the impact of explicitly incorporating both systematic and unsystematic risk into the development of low-enthalpy geothermal projects. We explore common practices, such as embedding unsystematic risk into discount rates—evaluating three rates: 7% (cost of capital), 10% (3% risk premium), and 13% (6% risk premium)—to examine their influence on project economics, data acquisition strategies, and DS selection. Our results show that including unsystematic risk in discount rates significantly reduces Expected Monetary Value (EMV), increases exploration costs, and impairs the ability to choose the most appropriate DS or to walk away when warranted. Crucially, this approach fails to meaningfully reduce expected losses. To overcome these limitations, we propose a more robust framework that integrates physical numerical models with probabilistic economic evaluations. This approach enables more accurate handling of both systematic and unsystematic risks, leading to better-informed decisions in geothermal field development.
- 7 December 2025
- Published by Springer Nature in Geothermal Energy
- Vol. 13 (1)
Open AccessIncorporating risk in geothermal field development planning: applying decision-theoretic agents
Geothermal field development requires decisions about data acquisition and the selection of an optimal development scenario (DS) under uncertainty. Effective planning must address two distinct types of risk: systematic risk, which affects the broader market, and unsystematic (idiosyncratic) risk, which is asset-specific. The inherent complexity of these decisions often leads to prolonged appraisal phases and suboptimal outcomes—particularly when it comes to incorporating risk into planning. This study applies decision-theoretic agents to assess the impact of explicitly incorporating both systematic and unsystematic risk into the development of low-enthalpy geothermal projects. We explore common practices, such as embedding unsystematic risk into discount rates—evaluating three rates: 7% (cost of capital), 10% (3% risk premium), and 13% (6% risk premium)—to examine their influence on project economics, data acquisition strategies, and DS selection. Our results show that including unsystematic risk in discount rates significantly reduces Expected Monetary Value (EMV), increases exploration costs, and impairs the ability to choose the most appropriate DS or to walk away when warranted. Crucially, this approach fails to meaningfully reduce expected losses. To overcome these limitations, we propose a more robust framework that integrates physical numerical models with probabilistic economic evaluations. This approach enables more accurate handling of both systematic and unsystematic risks, leading to better-informed decisions in geothermal field development.
- Open Access
Polymer Flooding in Space-Constrained Reservoirs: Technical and Economic Assessment of Liquid vs. Powder Polymers
This study evaluates the technical and economic feasibility of liquid polymer emulsions as substitutes for powder polymers in polymer flooding applications, particularly in space-constrained, low-permeability reservoirs in Austria. Rheological tests determined that target viscosities of 20 mPa·s at 20 °C and a shear rate of 7.94 s−1 were achieved using concentrations of 1200 ppm for liquid polymer 1 (LP1), 2250 ppm for liquid polymer 2 (LP2), and 1200–1400 ppm for powder polymers. Injectivity tests revealed that liquid polymers encountered challenges in 60 mD and 300 mD core plugs, with pressure stabilization not achieved at injection rates of 1–2.5 ft/day. Powder polymers demonstrated stable injectivity, with powder polymer 1 (PP1) showing an optimal performance at 10 ft/day and a low residual resistance factor (RRF). Two-phase core floods using PP1 and powder polymer 2 (PP2) at 1 ft/day yielded incremental oil recovery factors of approximately 5%, with a maximum of 8% observed for higher viscosity slugs. Economic analysis indicated that over a 3-year horizon, liquid polymers are 30% cheaper than powder polymer Option 1 but 100% more expensive than Option 2. Over a 10-year horizon, liquid polymers are 50% more expensive than both powder polymer options. Although liquid polymers offer logistical advantages, they are unsuitable for low-permeability reservoirs. Powdered polymers, particularly PP1, are recommended for pilot implementation due to superior injectivity, mechanical stability, and recovery performance.
Open AccessPolymer Flooding in Space-Constrained Reservoirs: Technical and Economic Assessment of Liquid vs. Powder Polymers
This study evaluates the technical and economic feasibility of liquid polymer emulsions as substitutes for powder polymers in polymer flooding applications, particularly in space-constrained, low-permeability reservoirs in Austria. Rheological tests determined that target viscosities of 20 mPa·s at 20 °C and a shear rate of 7.94 s−1 were achieved using concentrations of 1200 ppm for liquid polymer 1 (LP1), 2250 ppm for liquid polymer 2 (LP2), and 1200–1400 ppm for powder polymers. Injectivity tests revealed that liquid polymers encountered challenges in 60 mD and 300 mD core plugs, with pressure stabilization not achieved at injection rates of 1–2.5 ft/day. Powder polymers demonstrated stable injectivity, with powder polymer 1 (PP1) showing an optimal performance at 10 ft/day and a low residual resistance factor (RRF). Two-phase core floods using PP1 and powder polymer 2 (PP2) at 1 ft/day yielded incremental oil recovery factors of approximately 5%, with a maximum of 8% observed for higher viscosity slugs. Economic analysis indicated that over a 3-year horizon, liquid polymers are 30% cheaper than powder polymer Option 1 but 100% more expensive than Option 2. Over a 10-year horizon, liquid polymers are 50% more expensive than both powder polymer options. Although liquid polymers offer logistical advantages, they are unsuitable for low-permeability reservoirs. Powdered polymers, particularly PP1, are recommended for pilot implementation due to superior injectivity, mechanical stability, and recovery performance.
- 20 March 2025
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 30 (05) , 3104-3121
Temperature and Water Saturation Influence on Effective Hydrogen-Methane Diffusion in Reservoir Rocks: Estimation of Hydrogen Diffusive Losses
Summary: When hydrogen is stored underground in porous media, mixing of remaining hydrocarbon gas with hydrogen occurs. One of the major processes enhancing gas mixing is molecular diffusion, which depends on subsurface conditions (pressure and temperature), phase saturation, gas composition, and rock properties (porosity and tortuosity). Also, molecular diffusion of hydrogen through water-saturated caprock might lead to hydrogen losses during underground storage. Limited data is available describing the hydrogen-methane diffusion through reservoir rocks. Moreover, minor attention was given to the influence of temperature and water saturation on effective diffusion. To evaluate these effects, a series of experiments were carried out using an unsteady state method with fixed volumes. In this experimental setup, methane diffusing into a hydrogen-filled view cell is measured using infrared light spectroscopy. Diffusion through 100% water-saturated rock was measured using the pressure decay method. In this experiment, the partial pressure of the gas diffusing into saturated rock was measured and converted to concentration change. 3D numerical models were constructed to determine the diffusion coefficients by matching observed concentration changes. The measured bulk and effective hydrogen-methane diffusion coefficients within the temperature range of 28–100°C follow the kinetic gas theory. In both sets of experiments, the diffusion coefficient is proportional to temperature to the power of 3/2. Deviations from predicted diffusion coefficient values are smaller than 5%. Diffusion of gases (nitrogen, hydrogen, and methane) in water and formation brine was measured and found to be several orders of magnitude smaller than gas-gas diffusion. Hydrogen diffusion in 100% water-saturated Berea rock revealed a slow diffusion process. This indicates minor diffusive transport of hydrogen through water-saturated rocks (e.g., caprock shales). The results of effective hydrogen-methane diffusion measurements through partially saturated rock samples (40% and 60% water saturation) prove that water reduces effective pore space for gas mixing and, thus, the diffusion coefficient reduces with increasing water saturation. The data show that the effective tortuosity needs to increase with water saturation increase. Also, it was found that gas diffusivity is affected by saturation hysteresis. Several experiments were performed with a core sample saturated with the imbibition process revealing slower diffusion through a core plug in comparison to the drainage saturation process. Having obtained reliable hydrogen effective diffusion coefficients through saturated rock samples, the analytical equations and numerical models were developed to quantify diffusive hydrogen losses into the caprock. It is estimated that the amount of hydrogen losses due to diffusion accounts for 0.09% of cushion gas volume for case-study reservoirs during 30 years of underground hydrogen storage (UHS) operations. It was also shown that the introduction of hydrogen diffusion into the full-field simulation model might not be plausible due to the requirement of small grid sizes to minimize numerical dispersion effects. The study contributes a high-quality data set of effective diffusion coefficients with temperature, pressure, and water saturation. It is crucial to assess hydrogen losses through caprock and hydrogen-hydrocarbon gas mixing within the reservoir between high- and low-permeability layers. We also show an example of hydrogen loss assessment and point out the slow process of diffusion into caprock.
- 20 March 2025
- Published by Society of Petroleum Engineers (SPE) in SPE Journal
- Vol. 30 (05) , 3104-3121
Temperature and Water Saturation Influence on Effective Hydrogen-Methane Diffusion in Reservoir Rocks: Estimation of Hydrogen Diffusive Losses
Summary: When hydrogen is stored underground in porous media, mixing of remaining hydrocarbon gas with hydrogen occurs. One of the major processes enhancing gas mixing is molecular diffusion, which depends on subsurface conditions (pressure and temperature), phase saturation, gas composition, and rock properties (porosity and tortuosity). Also, molecular diffusion of hydrogen through water-saturated caprock might lead to hydrogen losses during underground storage. Limited data is available describing the hydrogen-methane diffusion through reservoir rocks. Moreover, minor attention was given to the influence of temperature and water saturation on effective diffusion. To evaluate these effects, a series of experiments were carried out using an unsteady state method with fixed volumes. In this experimental setup, methane diffusing into a hydrogen-filled view cell is measured using infrared light spectroscopy. Diffusion through 100% water-saturated rock was measured using the pressure decay method. In this experiment, the partial pressure of the gas diffusing into saturated rock was measured and converted to concentration change. 3D numerical models were constructed to determine the diffusion coefficients by matching observed concentration changes. The measured bulk and effective hydrogen-methane diffusion coefficients within the temperature range of 28–100°C follow the kinetic gas theory. In both sets of experiments, the diffusion coefficient is proportional to temperature to the power of 3/2. Deviations from predicted diffusion coefficient values are smaller than 5%. Diffusion of gases (nitrogen, hydrogen, and methane) in water and formation brine was measured and found to be several orders of magnitude smaller than gas-gas diffusion. Hydrogen diffusion in 100% water-saturated Berea rock revealed a slow diffusion process. This indicates minor diffusive transport of hydrogen through water-saturated rocks (e.g., caprock shales). The results of effective hydrogen-methane diffusion measurements through partially saturated rock samples (40% and 60% water saturation) prove that water reduces effective pore space for gas mixing and, thus, the diffusion coefficient reduces with increasing water saturation. The data show that the effective tortuosity needs to increase with water saturation increase. Also, it was found that gas diffusivity is affected by saturation hysteresis. Several experiments were performed with a core sample saturated with the imbibition process revealing slower diffusion through a core plug in comparison to the drainage saturation process. Having obtained reliable hydrogen effective diffusion coefficients through saturated rock samples, the analytical equations and numerical models were developed to quantify diffusive hydrogen losses into the caprock. It is estimated that the amount of hydrogen losses due to diffusion accounts for 0.09% of cushion gas volume for case-study reservoirs during 30 years of underground hydrogen storage (UHS) operations. It was also shown that the introduction of hydrogen diffusion into the full-field simulation model might not be plausible due to the requirement of small grid sizes to minimize numerical dispersion effects. The study contributes a high-quality data set of effective diffusion coefficients with temperature, pressure, and water saturation. It is crucial to assess hydrogen losses through caprock and hydrogen-hydrocarbon gas mixing within the reservoir between high- and low-permeability layers. We also show an example of hydrogen loss assessment and point out the slow process of diffusion into caprock.
- Open Access
Agrivoltaics, Opportunities for Hydrogen Generation, and Market Developments
To achieve deep decarbonization, renewable energy generation must be substantially increased. The technologies with the lowest levelized cost of electricity (LCOE) are land-based photovoltaics (PVs) and wind energy. Agri-PVs offer the potential for dual land use, combining energy generation with agricultural activities. However, the costs of agri-PVs are higher than those of ground-mounted PV. To enhance the competitiveness of agri-PV, we investigate the synergies between agri-PVs and hydrogen electrolysis through process simulation. Additionally, we analyse current technological developments in agri-PVs based on a market analysis of start-up companies. Our results indicate that the levelized cost of hydrogen (LCOH) can be comparable for agri-PVs and ground-mounted PVs due to the somewhat smoother electricity generation for the same installed capacity. The market analysis reveals the emergence of a technology ecosystem that integrates agri-PVs with next-generation agricultural technologies, such as sensors, robotics, and artificial intelligence (AI) agents, along with localized electricity generation forecasting. The integrated agri-PV and hydrogen generation system has significant global scaling potential for renewable energy generation. Furthermore, it positively impacts local economies and energy resilience, may reduce water scarcity in agriculture, and leverages advancements in AI, robotics, PV, and hydrogen generation technologies.
Open AccessAgrivoltaics, Opportunities for Hydrogen Generation, and Market Developments
To achieve deep decarbonization, renewable energy generation must be substantially increased. The technologies with the lowest levelized cost of electricity (LCOE) are land-based photovoltaics (PVs) and wind energy. Agri-PVs offer the potential for dual land use, combining energy generation with agricultural activities. However, the costs of agri-PVs are higher than those of ground-mounted PV. To enhance the competitiveness of agri-PV, we investigate the synergies between agri-PVs and hydrogen electrolysis through process simulation. Additionally, we analyse current technological developments in agri-PVs based on a market analysis of start-up companies. Our results indicate that the levelized cost of hydrogen (LCOH) can be comparable for agri-PVs and ground-mounted PVs due to the somewhat smoother electricity generation for the same installed capacity. The market analysis reveals the emergence of a technology ecosystem that integrates agri-PVs with next-generation agricultural technologies, such as sensors, robotics, and artificial intelligence (AI) agents, along with localized electricity generation forecasting. The integrated agri-PV and hydrogen generation system has significant global scaling potential for renewable energy generation. Furthermore, it positively impacts local economies and energy resilience, may reduce water scarcity in agriculture, and leverages advancements in AI, robotics, PV, and hydrogen generation technologies.
- Open Access
Alkali-Polymer Flooding in an Austrian Brownfield: From Laboratory to Field—Insights
We focus on optimizing oil displacement in brownfields using alkali polymers (AP) flooding. The goal is to enhance rock–fluid and fluid–fluid interactions to improve oil recovery. The evaluation includes detailed screening of AP mixtures to ensure cost-effectiveness and maximize chemical slug efficiency, using an AP pilot project in Austria as a case study. Key aspects of the study involve assessing fluid properties to select appropriate chemical concentrations. Important parameters include the stability of produced emulsions, interfacial tension (IFT) measurements, and rheological analyses. Rock–fluid interactions were examined through core flooding experiments on both low- and high-permeability core plugs to understand fluid dynamics in heterogeneous reservoirs. A novel part of the research involved simulating the in situ aging of the AP slug, which increases its anionicity over time. Two-phase core flooding with aged chemicals provided insights into the evolution of chemical effectiveness and interactions. We found that an alkali concentration of 7500 ppm was optimal for the AP slug, particularly in its interaction with dead oil with a high total acid number (TAN), leading to emulsions with microscopic instability. Single-phase core flooding showed that the AP slug from Vendor B outperformed that from Vendor A despite mechanical stability issues. However, the additional recovery factor (RF) for polymer A-based slugs was higher in both high- and low-permeability core plugs. The findings suggest that in situ aging of the AP slug could reduce costs and enhance injection performance.
Open AccessAlkali-Polymer Flooding in an Austrian Brownfield: From Laboratory to Field—Insights
We focus on optimizing oil displacement in brownfields using alkali polymers (AP) flooding. The goal is to enhance rock–fluid and fluid–fluid interactions to improve oil recovery. The evaluation includes detailed screening of AP mixtures to ensure cost-effectiveness and maximize chemical slug efficiency, using an AP pilot project in Austria as a case study. Key aspects of the study involve assessing fluid properties to select appropriate chemical concentrations. Important parameters include the stability of produced emulsions, interfacial tension (IFT) measurements, and rheological analyses. Rock–fluid interactions were examined through core flooding experiments on both low- and high-permeability core plugs to understand fluid dynamics in heterogeneous reservoirs. A novel part of the research involved simulating the in situ aging of the AP slug, which increases its anionicity over time. Two-phase core flooding with aged chemicals provided insights into the evolution of chemical effectiveness and interactions. We found that an alkali concentration of 7500 ppm was optimal for the AP slug, particularly in its interaction with dead oil with a high total acid number (TAN), leading to emulsions with microscopic instability. Single-phase core flooding showed that the AP slug from Vendor B outperformed that from Vendor A despite mechanical stability issues. However, the additional recovery factor (RF) for polymer A-based slugs was higher in both high- and low-permeability core plugs. The findings suggest that in situ aging of the AP slug could reduce costs and enhance injection performance.
- Open Access
Wind–Photovoltaic–Electrolyzer-Underground Hydrogen Storage System for Cost-Effective Seasonal Energy Storage
Photovoltaic (PV) and wind energy generation result in low greenhouse gas footprints and can supply electricity to the grid or generate hydrogen for various applications, including seasonal energy storage. Designing integrated wind–PV–electrolyzer underground hydrogen storage (UHS) projects is complex due to the interactions between components. Additionally, the capacities of PV and wind relative to the electrolyzer capacity and fluctuating electricity prices must be considered in the project design. To address these challenges, process modelling was applied using cost components and parameters from a project in Austria. The hydrogen storage part was derived from an Austrian hydrocarbon gas field considered for UHS. The results highlight the impact of the renewable energy source (RES) sizing relative to the electrolyzer capacity, the influence of different wind-to-PV ratios, and the benefits of selling electricity and hydrogen. For the case study, the levelized cost of hydrogen (LCOH) is EUR 6.26/kg for a RES-to-electrolyzer capacity ratio of 0.88. Oversizing reduces the LCOH to 2.61 €/kg when including electricity sales revenues, or EUR 4.40/kg when excluding them. Introducing annually fluctuating electricity prices linked to RES generation results in an optimal RES-to-electrolyzer capacity ratio. The RES-to-electrolyzer capacity can be dynamically adjusted in response to market developments. UHS provides seasonal energy storage in areas with mismatches between RES production and consumption. The main cost components are compression, gas conditioning, wells, and cushion gas. For the Austrian project, the levelized cost of underground hydrogen storage (LCHS) is 0.80 €/kg, with facilities contributing EUR 0.33/kg, wells EUR 0.09/kg, cushion gas EUR 0.23/kg, and OPEX EUR 0.16/kg. Overall, the analysis demonstrates the feasibility of integrated RES–hydrogen generation-seasonal energy storage projects in regions like Austria, with systems that can be dynamically adjusted to market conditions.
Open AccessWind–Photovoltaic–Electrolyzer-Underground Hydrogen Storage System for Cost-Effective Seasonal Energy Storage
Photovoltaic (PV) and wind energy generation result in low greenhouse gas footprints and can supply electricity to the grid or generate hydrogen for various applications, including seasonal energy storage. Designing integrated wind–PV–electrolyzer underground hydrogen storage (UHS) projects is complex due to the interactions between components. Additionally, the capacities of PV and wind relative to the electrolyzer capacity and fluctuating electricity prices must be considered in the project design. To address these challenges, process modelling was applied using cost components and parameters from a project in Austria. The hydrogen storage part was derived from an Austrian hydrocarbon gas field considered for UHS. The results highlight the impact of the renewable energy source (RES) sizing relative to the electrolyzer capacity, the influence of different wind-to-PV ratios, and the benefits of selling electricity and hydrogen. For the case study, the levelized cost of hydrogen (LCOH) is EUR 6.26/kg for a RES-to-electrolyzer capacity ratio of 0.88. Oversizing reduces the LCOH to 2.61 €/kg when including electricity sales revenues, or EUR 4.40/kg when excluding them. Introducing annually fluctuating electricity prices linked to RES generation results in an optimal RES-to-electrolyzer capacity ratio. The RES-to-electrolyzer capacity can be dynamically adjusted in response to market developments. UHS provides seasonal energy storage in areas with mismatches between RES production and consumption. The main cost components are compression, gas conditioning, wells, and cushion gas. For the Austrian project, the levelized cost of underground hydrogen storage (LCHS) is 0.80 €/kg, with facilities contributing EUR 0.33/kg, wells EUR 0.09/kg, cushion gas EUR 0.23/kg, and OPEX EUR 0.16/kg. Overall, the analysis demonstrates the feasibility of integrated RES–hydrogen generation-seasonal energy storage projects in regions like Austria, with systems that can be dynamically adjusted to market conditions.