Rispandi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Rispandi has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Cheng-Shane Chu
Ming Chi University of Technology
10 shared publications - Muhammad Imam Ammarullah
Department of Mechanical and Aerospace Engineering College of Engineering United Arab Emirates University Al Ain United Arab Emirates
4 shared publications Hernadewita
Post Graduate Industrial Engineering, University of Mercubuana Meruya Selatan Kembangan, West Jakarta 11650, Indonesia
3 shared publicationsA. Indriani
Electrical Engineering Department, University of Bengkulu W. R. Supratman, Kandang Limun, Bengkulu, Indonesia
2 shared publicationsCheng-Shane Chu
International Ph.D. Program in Innovative Technology of Biomedical Engineering and Medical Devices, Ming Chi University of Technology, New Taipei City, Taiwan
2 shared publicationsHendra
Mechanical Engineering Department, Faculty of Engineering University of Sultan Ageng Tirtayasa, Banten, Indonesia
2 shared publications
Latest Publications
- Open Access
- 31 May 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (6) , 301
Enhanced Crack Resistance Using Bamboo Fiber-Reinforced Polymer (FRP) Composite for Lightweight Structural Applications
Unsaturated polyester (UP) composites are widely utilized in engineering applications, including vehicle body structures, due to their ease of processing and good interfacial compatibility with natural fibers. However, the inherent brittleness of UP limits its performance under impact or tensile loading, as it exhibits minimal plastic deformation and is prone to crack initiation and propagation. In this study, bamboo fiber was incorporated into the UP matrix at various mixing ratios to enhance its crack resistance. After achieving uniform dispersion, the composites were subjected to a splitting tensile test to evaluate their crack resistance behavior. The results indicate that the composite containing 80% polyester exhibits the highest fracture toughness, with a crack resistance value of K1C = 1.396 MPa·m0.5. This value represents a 192.03% improvement compared with neat polyester (K1C = 0.713 MPa·m0.5). The enhanced crack resistance is attributed to the fiber bridging and energy-absorption mechanisms introduced by the bamboo fibers. These findings demonstrate the effectiveness of bamboo fiber reinforcement in improving the fracture performance of UP-based composites, highlighting their potential for use in lightweight structural applications.
- 31 May 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (6) , 301
Open AccessEnhanced Crack Resistance Using Bamboo Fiber-Reinforced Polymer (FRP) Composite for Lightweight Structural Applications
Unsaturated polyester (UP) composites are widely utilized in engineering applications, including vehicle body structures, due to their ease of processing and good interfacial compatibility with natural fibers. However, the inherent brittleness of UP limits its performance under impact or tensile loading, as it exhibits minimal plastic deformation and is prone to crack initiation and propagation. In this study, bamboo fiber was incorporated into the UP matrix at various mixing ratios to enhance its crack resistance. After achieving uniform dispersion, the composites were subjected to a splitting tensile test to evaluate their crack resistance behavior. The results indicate that the composite containing 80% polyester exhibits the highest fracture toughness, with a crack resistance value of K1C = 1.396 MPa·m0.5. This value represents a 192.03% improvement compared with neat polyester (K1C = 0.713 MPa·m0.5). The enhanced crack resistance is attributed to the fiber bridging and energy-absorption mechanisms introduced by the bamboo fibers. These findings demonstrate the effectiveness of bamboo fiber reinforcement in improving the fracture performance of UP-based composites, highlighting their potential for use in lightweight structural applications.
- Open Access
- 4 February 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (2) , 80
Flexural Performance of Unsaturated Polyester Composites Reinforced with Coconut Shell Charcoal Powder for Lightweight Structural Applications
Polymer-based composites have emerged as viable alternatives to metals for applications requiring reduced weight, corrosion resistance, and cost-effectiveness; however, their relatively low mechanical strength remains a significant limitation. This study evaluates the flexural performance of unsaturated polyester composites reinforced with coconut shell charcoal (CC) powder at filler contents of 0%, 10%, 20%, and 30% by weight, in accordance with ASTM D790. The incorporation of 20 wt% CC yielded the highest flexural strength of 132.43 MPa, representing a 153% improvement compared to pure polyester (52.10 MPa). Flexural modulus also increased substantially at this composition, indicating enhanced stiffness resulting from improved interfacial bonding and efficient stress transfer. In contrast, increasing the filler content beyond 20 wt% resulted in a reduction of up to 32% in strength, attributed to particle agglomeration and void formation. Overall, the results identify 20 wt% CC as the optimal reinforcement level, significantly improving energy absorption and bending resistance, thereby positioning this composite as a promising candidate for lightweight structural applications.
- 4 February 2026
- Published by MDPI AG in Journal of Composites Science
- Vol. 10 (2) , 80
Open AccessFlexural Performance of Unsaturated Polyester Composites Reinforced with Coconut Shell Charcoal Powder for Lightweight Structural Applications
Polymer-based composites have emerged as viable alternatives to metals for applications requiring reduced weight, corrosion resistance, and cost-effectiveness; however, their relatively low mechanical strength remains a significant limitation. This study evaluates the flexural performance of unsaturated polyester composites reinforced with coconut shell charcoal (CC) powder at filler contents of 0%, 10%, 20%, and 30% by weight, in accordance with ASTM D790. The incorporation of 20 wt% CC yielded the highest flexural strength of 132.43 MPa, representing a 153% improvement compared to pure polyester (52.10 MPa). Flexural modulus also increased substantially at this composition, indicating enhanced stiffness resulting from improved interfacial bonding and efficient stress transfer. In contrast, increasing the filler content beyond 20 wt% resulted in a reduction of up to 32% in strength, attributed to particle agglomeration and void formation. Overall, the results identify 20 wt% CC as the optimal reinforcement level, significantly improving energy absorption and bending resistance, thereby positioning this composite as a promising candidate for lightweight structural applications.
- Open Access
- 11 September 2025
- Published by Elsevier in Next Materials
- Vol. 9
A review on the formation, recovery, and properties of coal fly ash (CFA)-derived microspheres for sustainable technologies and biomedical applications
- 11 September 2025
- Published by Elsevier in Next Materials
- Vol. 9
Open AccessA review on the formation, recovery, and properties of coal fly ash (CFA)-derived microspheres for sustainable technologies and biomedical applications
- Open Access
- 5 July 2025
- Published by Elsevier in Talanta Open
- Vol. 12
High-performance ratiometric optical oxygen sensor fabricated via 3Dprinted silicone for biomedical applications
- 5 July 2025
- Published by Elsevier in Talanta Open
- Vol. 12
Open AccessHigh-performance ratiometric optical oxygen sensor fabricated via 3Dprinted silicone for biomedical applications
- Open Access
Advanced Optimization of Optical Carbon Dioxide Sensor Through Sensitivity Enhancement in Anodic Aluminum Oxide Substrate
The current research developed an optical carbon dioxide (CO2) sensor using anodized aluminum oxide (AAO) as the substrate. We developed an optical carbon dioxide (CO2) sensor utilizing CdSe/ZnS quantum dots (QDs) as the fluorescent dye and Phenol Red as the pH indicator. The QDs acted as the CO2-responsive fluorophore and were embedded in a polyimide butyl methacrylate (polyIBM) matrix. This sensing solution was applied to an anodized aluminum oxide (AAO) substrate, which provided a porous and stable platform for sensor fabrication. Photoluminescence measurements were conducted using the coated AAO substrate, with excitation from a 405 nm LED light source. The sensor exhibited red fluorescence emission at 570 nm and could detect CO2 concentrations in the linear range of 0–100%. Experimental results showed that fluorescence intensity increased with CO2 concentration, achieving a sensitivity of 211. A wavelength shift of 0.1657 nm/% was observed, indicating strong interactions among CO2 molecules, Phenol Red, and the QDs within the AAO matrix. The sensor demonstrated a response time of 55 s and a recovery time of 120 s. These results confirm the effectiveness of this optical sensing approach in minimizing fluctuations from the excitation light source and highlight the potential of the AAO-supported QDs and Phenol Red composite as a reliable CO2 sensing material. This advancement holds promise for applications in both medical and industrial fields.
Open AccessAdvanced Optimization of Optical Carbon Dioxide Sensor Through Sensitivity Enhancement in Anodic Aluminum Oxide Substrate
The current research developed an optical carbon dioxide (CO2) sensor using anodized aluminum oxide (AAO) as the substrate. We developed an optical carbon dioxide (CO2) sensor utilizing CdSe/ZnS quantum dots (QDs) as the fluorescent dye and Phenol Red as the pH indicator. The QDs acted as the CO2-responsive fluorophore and were embedded in a polyimide butyl methacrylate (polyIBM) matrix. This sensing solution was applied to an anodized aluminum oxide (AAO) substrate, which provided a porous and stable platform for sensor fabrication. Photoluminescence measurements were conducted using the coated AAO substrate, with excitation from a 405 nm LED light source. The sensor exhibited red fluorescence emission at 570 nm and could detect CO2 concentrations in the linear range of 0–100%. Experimental results showed that fluorescence intensity increased with CO2 concentration, achieving a sensitivity of 211. A wavelength shift of 0.1657 nm/% was observed, indicating strong interactions among CO2 molecules, Phenol Red, and the QDs within the AAO matrix. The sensor demonstrated a response time of 55 s and a recovery time of 120 s. These results confirm the effectiveness of this optical sensing approach in minimizing fluctuations from the excitation light source and highlight the potential of the AAO-supported QDs and Phenol Red composite as a reliable CO2 sensing material. This advancement holds promise for applications in both medical and industrial fields.
- Open Access
- 11 February 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (4) , 273
Fabrication of an Optical Sensor Based on Eosin-Y-Doped Electrospun Fibers for Ammonia Detection via Wavelength Shifts
This research presents a simple and effective technique to fabricate an optical sensor for ammonia detection, leveraging emission wavelength shifts as the sensing mechanism. The sensor comprises a cellulose acetate matrix doped with Eosin-Y, which serves as the electrospinning material. Photoluminescent micro/nanofibers were successfully fabricated using electrospinning and were stimulated by a 380 nm central wavelength LED. The Eosin-Y-doped electrospun fiber membranes exhibited a red emission peak at 580 nm, allowing ammonia to be detected in the linear concentration range of 0–500 ppm. The experimental results demonstrated a high sensitivity of 8.11, with a wavelength shift sensitivity of 0.029 nm/ppm in response to ammonia concentration changes. This optical sensing method effectively mitigates the influence of fluctuations in excitation light intensity, offering improved reliability. The Eosin-Y-containing electrospun fibers show great potential as a practical sensing material for detecting ammonia gas concentrations with high precision, supporting diverse applications in medical diagnostics, environmental monitoring, and industrial processes.
- 11 February 2025
- Published by MDPI AG in Nanomaterials
- Vol. 15 (4) , 273
Open AccessFabrication of an Optical Sensor Based on Eosin-Y-Doped Electrospun Fibers for Ammonia Detection via Wavelength Shifts
This research presents a simple and effective technique to fabricate an optical sensor for ammonia detection, leveraging emission wavelength shifts as the sensing mechanism. The sensor comprises a cellulose acetate matrix doped with Eosin-Y, which serves as the electrospinning material. Photoluminescent micro/nanofibers were successfully fabricated using electrospinning and were stimulated by a 380 nm central wavelength LED. The Eosin-Y-doped electrospun fiber membranes exhibited a red emission peak at 580 nm, allowing ammonia to be detected in the linear concentration range of 0–500 ppm. The experimental results demonstrated a high sensitivity of 8.11, with a wavelength shift sensitivity of 0.029 nm/ppm in response to ammonia concentration changes. This optical sensing method effectively mitigates the influence of fluctuations in excitation light intensity, offering improved reliability. The Eosin-Y-containing electrospun fibers show great potential as a practical sensing material for detecting ammonia gas concentrations with high precision, supporting diverse applications in medical diagnostics, environmental monitoring, and industrial processes.
- Open Access
- 13 January 2025
- Published by Elsevier in Results in Optics
- Vol. 18
Optical dual gas sensor for biomedical monitoring of NO and O2 based on electrospun fibers containing CsPbBr3 QDs and PtTFPP
- 13 January 2025
- Published by Elsevier in Results in Optics
- Vol. 18
Open AccessOptical dual gas sensor for biomedical monitoring of NO and O2 based on electrospun fibers containing CsPbBr3 QDs and PtTFPP
- Open Access
- 25 November 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (51) , 38135-38145
Ratiometric optical dual gas sensor for simultaneous detection of nitric oxide and oxygen intended for healthcare, biological, and biomedical applications
Developing efficient and reliable gas sensors for the simultaneous detection of multiple gases is paramount in various fields, specifically healthcare, biological, and biomedical applications. In this study, we present a novel ratiometric optical dual gas sensor based on perovskite quantum dots (PQDs) to detect nitric oxide and oxygen simultaneously. All dye molecules were excited using a 405 nm LED in the experimental setup. The results obtained from the experiments reveal that both the optical NO and O2 sensors exhibit linear Stern–Volmer plots, and the sensitivities observed for NO and O2 sensors were approximately 2.4 and 2.8, respectively. The response and recovery times of the optical NO sensor are 67 s and 69 s, respectively. O2 sensor response and recovery times are 66 s and 68 s, respectively. In this work, the ratiometric optical dual gas sensing approach suppressed the effects of spurious fluctuations in the intensity of external and excitation sources.
- 25 November 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (51) , 38135-38145
Open AccessRatiometric optical dual gas sensor for simultaneous detection of nitric oxide and oxygen intended for healthcare, biological, and biomedical applications
Developing efficient and reliable gas sensors for the simultaneous detection of multiple gases is paramount in various fields, specifically healthcare, biological, and biomedical applications. In this study, we present a novel ratiometric optical dual gas sensor based on perovskite quantum dots (PQDs) to detect nitric oxide and oxygen simultaneously. All dye molecules were excited using a 405 nm LED in the experimental setup. The results obtained from the experiments reveal that both the optical NO and O2 sensors exhibit linear Stern–Volmer plots, and the sensitivities observed for NO and O2 sensors were approximately 2.4 and 2.8, respectively. The response and recovery times of the optical NO sensor are 67 s and 69 s, respectively. O2 sensor response and recovery times are 66 s and 68 s, respectively. In this work, the ratiometric optical dual gas sensing approach suppressed the effects of spurious fluctuations in the intensity of external and excitation sources.
- Open Access
- 14 August 2023
- Published by MDPI AG in Chemosensors
- Vol. 11 (8) , 454
Optical Dual Gas Sensor for Simultaneous Detection of Nitric Oxide and Oxygen
This work presents a new optical dual sensor based on PtTFPP-containing electrospun fibers and CsPbBr3 perovskite quantum dots (PQDs) for simultaneous detection of oxygen (O2) and nitric oxide (NO) gases, wherein PtTFPP-containing electrospun fibers for O2 sensing was based on electrospinning process fabricated by platinum(II) meso-tetrakis (pentafluorophenyl) porphyrin (PtTFPP) complex immobilized in cellulose acetate (CA) matrix. CsPbBr3 PQDs were used as NO-sensitive material and coated on the surface of PtTFPP-containing electrospun fibers. Both materials were excited by a UV LED with a central wavelength of 380 nm, and the fluorescence intensities of sensing materials were recorded and analyzed with a spectrometer. The experiment results show that the optical NO and O2 sensors have linear Stern–Volmer plots, and the sensitivities are around 2.7 and 10.7, respectively. The response and recovery times of the optical NO sensor are 71 and 109 s, respectively. For optical O2, response and recovery times are 60 and 65 s, respectively. The optical dual sensor with a new method based on fluorescent dye containing electrospun fibers and coated with CsPbBr3 PQDs has been successfully developed to detect NO and O2 gases simultaneously. The optical dual gas sensor provides great potential for practical applications with low cost and ease of fabrication.
- 14 August 2023
- Published by MDPI AG in Chemosensors
- Vol. 11 (8) , 454
Open AccessOptical Dual Gas Sensor for Simultaneous Detection of Nitric Oxide and Oxygen
This work presents a new optical dual sensor based on PtTFPP-containing electrospun fibers and CsPbBr3 perovskite quantum dots (PQDs) for simultaneous detection of oxygen (O2) and nitric oxide (NO) gases, wherein PtTFPP-containing electrospun fibers for O2 sensing was based on electrospinning process fabricated by platinum(II) meso-tetrakis (pentafluorophenyl) porphyrin (PtTFPP) complex immobilized in cellulose acetate (CA) matrix. CsPbBr3 PQDs were used as NO-sensitive material and coated on the surface of PtTFPP-containing electrospun fibers. Both materials were excited by a UV LED with a central wavelength of 380 nm, and the fluorescence intensities of sensing materials were recorded and analyzed with a spectrometer. The experiment results show that the optical NO and O2 sensors have linear Stern–Volmer plots, and the sensitivities are around 2.7 and 10.7, respectively. The response and recovery times of the optical NO sensor are 71 and 109 s, respectively. For optical O2, response and recovery times are 60 and 65 s, respectively. The optical dual sensor with a new method based on fluorescent dye containing electrospun fibers and coated with CsPbBr3 PQDs has been successfully developed to detect NO and O2 gases simultaneously. The optical dual gas sensor provides great potential for practical applications with low cost and ease of fabrication.