JLJun Li

Jun Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jun Li has a total of 22 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Research Progress and Prospect of Solid Electrolyte Garnet-Type Li7La3Zr2O12

    by Peizhuang Wang, Lipeng Xu, Xiantao Li, Renyi Yang, Jun Li

    At present, lithium lanthanum zirconate (LLZO) is regarded as one of the most promising solid-state electrolyte materials due to its high ionic conductivity (about 10−3 S/cm at room temperature), high chemical stability, and excellent chemical stability toward cathode materials and lithium metal anodes. However, there are several problems, such as poor interface contact with the lithium metal anode resulting in high interface impedance, a high sintering densification temperature (usually >1200 °C), a complex preparation process, and high cost. In recent years, researchers have conducted extensive studies on LLZO and achieved remarkable progress and results. This paper systematically reviews the research progress of LLZO’s structural characteristics, conductive mechanism, preparation methods, improvement strategies, and so on.

  • Open Access

    Electrodeposition and Corrosion Resistance of Ni-Mo Alloy Coating: Effect of Electroplating Bath pH Values

    by Xi Shi, Shiyuan Zhu, Qiongyu Zhou, Bo Liang, Jun Li, Guangji Li, Longquan Chen, Peijun Xu

    Ni-Mo alloy coating has shown exciting potential as a candidate to replace chromium coating. In this paper, Ni-Mo alloy coatings were successfully electrodeposited from a citrate/ammonia bath, and the effect of the bath pH values over a wide range (4–10) on the characteristics and corrosion resistance of Ni-Mo alloy coating was studied in detail. Results show that all the deposited Ni-Mo alloy coatings consist of a crystalline solid-solution Ni(Mo) fcc structure. An increase in bath pH values could facilitate the deposition of Mo, thereby increasing the Mo content and decreasing the crystallite size of Ni-Mo alloy coatings. However, there are subtle gaps between the coarse grains on the surface of the Ni-Mo alloy coating deposited at pH 10. These subtle gaps tend to form between the coarse grains on the surface of the electrodeposited Ni-Mo alloy coating because of the relatively high Mo content, refined grains, and appropriate morphology. The Ni-Mo alloy coating deposited at pH 9 exhibits optimal corrosion resistance, attributed to its lowest corrosion current density icorr (7.31 × 10−6 A cm−2), the strongest polarization resistance (11.13 kΩ·cm−2), and impedance value, which are mainly contributed to by the coating resistance and charge-transfer resistance.


  • Open Access

    Structure and Ionic Conductivity of Ga and Nb Dual Doped LLZO Synthesized by Sol-Gel Method

    by Jun Li, Fuzhong Wang, Leichao Meng, Tao Gao, Bo Liang, Hang Zhang, Meili Cui, Xinxin Lu, Ying Cao, Jiyong Chen

    More and more attention has been focused on Li7La3Zr2O12 (LLZO) because of the high ionic conductivity and excellent chemical stability. It is great significance to find suitable dopants for locking cubic LLZO and improving the conductivity of Li+ ions. The uniform nano powder can be obtained by the sol gel synthetic method, which is conducive to maintaining high sintering activity. In this work, Ga and Nb dual doped LLZO solid electrolyte powders were synthesized via sol gel method, and Ga and Nb dual doped LLZO solid electrolyte ceramic were obtained via traditional solid state sintering method. The phase and microstructure of Ga and Nb co-doped LLZO solid electrolyte were analyzed by combine X-ray diffraction with scanning electron microscope. The impedance of Ga and Nb dual doped LLZO (Li6.8-3xGaxLa3Zr1.8Nb0.2O12 (0≤x≤0.3)) solid electrolyte was measured by the electrochemical workstation, and then the conductivity was calculated. The results show that when the doping amount of Ga is x=0.2, it is a pure cubic LLZO structure with the highest conductivity value of 3.7×10-4 S cm-1 (tested at room temperature) due to the sample has a high relative density and reaches the optimal Li+ vacancy concentration.


  • Open Access

    The Modification of WO3 for Lithium Batteries with Nickel-Rich Ternary Cathode Materials

    by Lipeng Xu, Chunjiang Bao, Haobing Zhou, Jun Li

    Nickel-rich ternary cathode materials (NRTCMs) have high energy density and a long cycle life, making them one of the cathode materials of LIB that are currently receiving much attention. However, it has shortcomings such as poor cycling performance (CP) and a high-capacity decay rate. Because of this, the study analyzed the modification effect of WO3 on NRTCM lithium batteries by preparing WO3-modified poly-crystal and single-crystal NCM622 materials under the existing conditions of better original cathode materials as reference samples. The results showed that in the morphology and structure testing, with the increase of WO3 addition, the c/a values of all NCM622-WO3 samples were greater than 4.95. In the analysis of cycling and rate performance (CRP), as W increased, the rate performance (RP) of the NCM622-W4.0 sample had a discharge specific capacity ratio of 86.2% at 10.0 C/1.0 C. In cyclic voltammetry testing, when the addition amount of WO3 was 1.0%, the polarization degree of SC-NCM622 sample was the weakest. In the AC impedance test, after six cycles, compared with the original sample, the Ret and R + Rct values of the NCM622-W sample modified with WO3 showed a significant downward trend. The above results prove that WO3 modification can lower the polarization of the material, effectively raising the CRP of the battery. It provides a reference path for the further progress of high capacity and stability ternary cathode materials.