Tomoyuki Kurioka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Tomoyuki Kurioka has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
- Tso-Fu Mark Chang
Materials and Structures Laboratory Institute of Integrated Research Institute of Science Tokyo Kanagawa Japan
23 shared publications - Masato Sone
Institute of Science Tokyo
16 shared publications - Chun-Yi Chen
Department of Materials and Engineering, Institute of Science Tokyo, Yokohama 226-8501, Japan
12 shared publications - Yung-Jung Hsu
National yang Ming Chiao Tung University
10 shared publications Masato Sone
Materials and Structures Laboratory Institute of Integrated Research Institute of Science Tokyo Yokohama Japan
9 shared publicationsChun-Yi Chen
8 shared publications
Latest Publications
- Open Access
- 13 August 2026
- Published by Wiley in Electrochemical Science Advances
- Vol. 6 (5) , e70040
Polyaniline Derivatives Decorated With Atomic‐Scale Gold Toward Electrochemical Non‐Enzymatic Glucose Sensing
This paper reports polyaniline derivatives, such as polyaniline, poly( o ‐toluidine) and poly( o ‐methoxyaniline), decorated with atomic‐scale gold clusters for electrochemical non‐enzymatic glucose sensing. Atomic‐scale gold clusters are deposited onto the electrodeposited polyaniline derivatives via cyclic electrodeposition. Their catalytic activity for glucose oxidation is evaluated by cyclic voltammetry measurements. The introduced functional groups affect their catalytic performance. All fabricated atomic‐scale gold cluster‐decorated polyaniline derivatives demonstrate a wide detection range, low detection limit, high tolerance to chloride ion poisoning and good operational stability. Among the prepared electrodes, using poly( o ‐methoxyaniline) as a supporting material results in the highest catalytic activity toward glucose oxidation with better selectivity. Au 2 /POMA electrode shows a sensitivity of 200.9 µA mM −1 cm −2 , and a limit of detection of 0.30 mM, as well as the best selectivity and stability. These results demonstrate that the introduction of functional groups onto the polyaniline main chains enhances electrode properties using atomic‐scale gold clusters toward non‐enzymatic glucose sensing applications.
- 13 August 2026
- Published by Wiley in Electrochemical Science Advances
- Vol. 6 (5) , e70040
Open AccessPolyaniline Derivatives Decorated With Atomic‐Scale Gold Toward Electrochemical Non‐Enzymatic Glucose Sensing
This paper reports polyaniline derivatives, such as polyaniline, poly( o ‐toluidine) and poly( o ‐methoxyaniline), decorated with atomic‐scale gold clusters for electrochemical non‐enzymatic glucose sensing. Atomic‐scale gold clusters are deposited onto the electrodeposited polyaniline derivatives via cyclic electrodeposition. Their catalytic activity for glucose oxidation is evaluated by cyclic voltammetry measurements. The introduced functional groups affect their catalytic performance. All fabricated atomic‐scale gold cluster‐decorated polyaniline derivatives demonstrate a wide detection range, low detection limit, high tolerance to chloride ion poisoning and good operational stability. Among the prepared electrodes, using poly( o ‐methoxyaniline) as a supporting material results in the highest catalytic activity toward glucose oxidation with better selectivity. Au 2 /POMA electrode shows a sensitivity of 200.9 µA mM −1 cm −2 , and a limit of detection of 0.30 mM, as well as the best selectivity and stability. These results demonstrate that the introduction of functional groups onto the polyaniline main chains enhances electrode properties using atomic‐scale gold clusters toward non‐enzymatic glucose sensing applications.
- Open Access
- 3 August 2026
- Published by MDPI AG in Electrochem
- Vol. 7 (3) , 22
Poly(3,4-Ethylenedioxythiophene)-Centered TiO2 Hybrid Electrodes for HER- and OER-Relevant Photoelectrochemical Responses
Photoelectrochemical (PEC) energy conversion is a promising approach for solar-to-chemical fuel production, but its practical performance is limited by insufficient visible-light utilization and charge-carrier recombination. Here, poly(3,4-ethylenedioxythiophene) (PEDOT)-centered TiO2 hybrid electrodes were prepared by electropolymerizing PEDOT on FTO substrates, followed by electrochemical doping/dedoping treatment and coating with commercial TiO2 as a model oxide semiconductor. SEM, EDS, and LIBS analyses confirmed the successful deposition of TiO2 onto PEDOT-based films. Four-probe measurements showed that electrochemical doping reduced the apparent resistance of PEDOT-based electrodes, while UV–vis spectroscopy revealed enhanced long-wavelength absorption for doped PEDOT-containing films. PEC measurements using TiO2, PEDOT, and TiO2–PEDOT electrodes showed that PEDOT-containing electrodes exhibited much stronger photoresponses than commercial TiO2 alone under both HER- and OER-relevant conditions. The TiO2–PEDOT electrode showed stable photocurrent responses under chopped illumination and retained photoresponse under illumination transmitted through a 410 nm UV-cut filter, supporting the primary role of PEDOT in visible-light utilization. Long-term chronoamperometry further showed that TiO2–PEDOT retained approximately 99.0% of its cathodic current under HER-relevant conditions and 91.9% of its anodic current under OER-relevant conditions after 5200 s of continuous illumination. The improved response of TiO2–PEDOT compared with PEDOT alone suggests that TiO2/PEDOT physical contact may assist interfacial charge separation and transport. These findings demonstrate that PEDOT-centered metal oxide/conducting polymer hybrids provide a useful model platform for visible-light-responsive PEC energy-conversion applications.
- 3 August 2026
- Published by MDPI AG in Electrochem
- Vol. 7 (3) , 22
Open AccessPoly(3,4-Ethylenedioxythiophene)-Centered TiO2 Hybrid Electrodes for HER- and OER-Relevant Photoelectrochemical Responses
Photoelectrochemical (PEC) energy conversion is a promising approach for solar-to-chemical fuel production, but its practical performance is limited by insufficient visible-light utilization and charge-carrier recombination. Here, poly(3,4-ethylenedioxythiophene) (PEDOT)-centered TiO2 hybrid electrodes were prepared by electropolymerizing PEDOT on FTO substrates, followed by electrochemical doping/dedoping treatment and coating with commercial TiO2 as a model oxide semiconductor. SEM, EDS, and LIBS analyses confirmed the successful deposition of TiO2 onto PEDOT-based films. Four-probe measurements showed that electrochemical doping reduced the apparent resistance of PEDOT-based electrodes, while UV–vis spectroscopy revealed enhanced long-wavelength absorption for doped PEDOT-containing films. PEC measurements using TiO2, PEDOT, and TiO2–PEDOT electrodes showed that PEDOT-containing electrodes exhibited much stronger photoresponses than commercial TiO2 alone under both HER- and OER-relevant conditions. The TiO2–PEDOT electrode showed stable photocurrent responses under chopped illumination and retained photoresponse under illumination transmitted through a 410 nm UV-cut filter, supporting the primary role of PEDOT in visible-light utilization. Long-term chronoamperometry further showed that TiO2–PEDOT retained approximately 99.0% of its cathodic current under HER-relevant conditions and 91.9% of its anodic current under OER-relevant conditions after 5200 s of continuous illumination. The improved response of TiO2–PEDOT compared with PEDOT alone suggests that TiO2/PEDOT physical contact may assist interfacial charge separation and transport. These findings demonstrate that PEDOT-centered metal oxide/conducting polymer hybrids provide a useful model platform for visible-light-responsive PEC energy-conversion applications.
- Open Access
- 29 July 2026
- Published by Elsevier in SSRN Electronic Journal
Cu–EDTA-Assisted Electrodeposition of Cu/Polyaniline Composite Electrodes for Non-Enzymatic Electrochemical Glucose Sensing
Non-enzymatic electrochemical glucose sensors based on non-noble-metal catalysts are attracting increasing attention as a stable and low-cost alternative to enzyme-based systems. In this study, a Cu/polyaniline composite electrode was prepared by modifying copper nanoparticles (Cu NPs) on polyaniline (PANI) in order to achieve controllable metal nucleation and improved catalytic activity. To obtain uniformly dispersed Cu species, ethylenediaminetetraacetic acid (EDTA) was used to form a Cu–EDTA complex as the metal precursor for electrodeposition on the conductive PANI film. The coordination behavior of the Cu–EDTA complex and its pH-dependent reduction characteristics were systematically investigated to clarify its applicability for controlled Cu deposition. Structural and elemental analyses showed that adjusting the Cu2+/EDTA4− molar ratio enables uniform loading of Cu NPs on the PANI matrix, and that under weakly acidic conditions a ratio of 1:1 yields the most homogeneous Cu distribution. Electrochemical evaluation demonstrated that the resulting Cu/PANI electrode exhibits an enhanced catalytic response toward glucose oxidation, consistent with the increased electrocatalytic activity of the Cu species. These results confirm the effectiveness of Cu–EDTA complexes in controlling the deposition of non-precious Cu on conductive polymers and provide a practical strategy for low-cost, high-performance electrodes designed for non-enzymatic glucose sensing.
- 29 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCu–EDTA-Assisted Electrodeposition of Cu/Polyaniline Composite Electrodes for Non-Enzymatic Electrochemical Glucose Sensing
Non-enzymatic electrochemical glucose sensors based on non-noble-metal catalysts are attracting increasing attention as a stable and low-cost alternative to enzyme-based systems. In this study, a Cu/polyaniline composite electrode was prepared by modifying copper nanoparticles (Cu NPs) on polyaniline (PANI) in order to achieve controllable metal nucleation and improved catalytic activity. To obtain uniformly dispersed Cu species, ethylenediaminetetraacetic acid (EDTA) was used to form a Cu–EDTA complex as the metal precursor for electrodeposition on the conductive PANI film. The coordination behavior of the Cu–EDTA complex and its pH-dependent reduction characteristics were systematically investigated to clarify its applicability for controlled Cu deposition. Structural and elemental analyses showed that adjusting the Cu2+/EDTA4− molar ratio enables uniform loading of Cu NPs on the PANI matrix, and that under weakly acidic conditions a ratio of 1:1 yields the most homogeneous Cu distribution. Electrochemical evaluation demonstrated that the resulting Cu/PANI electrode exhibits an enhanced catalytic response toward glucose oxidation, consistent with the increased electrocatalytic activity of the Cu species. These results confirm the effectiveness of Cu–EDTA complexes in controlling the deposition of non-precious Cu on conductive polymers and provide a practical strategy for low-cost, high-performance electrodes designed for non-enzymatic glucose sensing.
- 11 June 2026
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 9 (24) , 11492-11501
Sodium-Containing Spinel NiFe 2 O 4 Nanoparticles for Enhanced Supercapacitor Performance
- 11 June 2026
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 9 (24) , 11492-11501
Sodium-Containing Spinel NiFe 2 O 4 Nanoparticles for Enhanced Supercapacitor Performance
- Open Access
- 5 May 2026
- Published by Elsevier in SSRN Electronic Journal
Cooling-Trajectory-Controlled Cation Redistribution in Spinel CoFe2O4 for Photooxidation and Peroxide-Assisted Oxidation
Solar-driven photooxidation is a promising route for sustainable chemical transformation, but its efficiency depends on the interplay among light harvesting, charge utilization, and surface redox activity. Spinel CoFe2O4 is an attractive multifunctional catalyst because its narrow band gap, ferrimagnetic recoverability, and multivalent Co/Fe redox chemistry support both photoinduced oxidation and peroxide-assisted Fenton-like pathways. Here, the post-annealing cooling trajectory is used as a thermal-processing parameter to regulate cation distribution within the CoFe2O4 spinel lattice. Structural and spectroscopic analyses show that nitrogen quenching, natural cooling, and oven cooling systematically modulate cation site occupancy, yielding apparent inversion degrees of approximately 61%, 68%, and 76%, respectively. Although the rapidly quenched sample shows slightly stronger visible-light absorption, it also exhibits higher photoluminescence intensity, indicating less efficient charge utilization. In contrast, the oven-cooled sample shows more favorable charge-separation behavior and superior activity in both photooxidation and peroxide-assisted dark oxidation. Using malachite green oxidation as a model probe reaction, we establish a processing–structure–activity relationship and show that charge utilization, rather than optical absorption alone, governs performance.
- 5 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCooling-Trajectory-Controlled Cation Redistribution in Spinel CoFe2O4 for Photooxidation and Peroxide-Assisted Oxidation
Solar-driven photooxidation is a promising route for sustainable chemical transformation, but its efficiency depends on the interplay among light harvesting, charge utilization, and surface redox activity. Spinel CoFe2O4 is an attractive multifunctional catalyst because its narrow band gap, ferrimagnetic recoverability, and multivalent Co/Fe redox chemistry support both photoinduced oxidation and peroxide-assisted Fenton-like pathways. Here, the post-annealing cooling trajectory is used as a thermal-processing parameter to regulate cation distribution within the CoFe2O4 spinel lattice. Structural and spectroscopic analyses show that nitrogen quenching, natural cooling, and oven cooling systematically modulate cation site occupancy, yielding apparent inversion degrees of approximately 61%, 68%, and 76%, respectively. Although the rapidly quenched sample shows slightly stronger visible-light absorption, it also exhibits higher photoluminescence intensity, indicating less efficient charge utilization. In contrast, the oven-cooled sample shows more favorable charge-separation behavior and superior activity in both photooxidation and peroxide-assisted dark oxidation. Using malachite green oxidation as a model probe reaction, we establish a processing–structure–activity relationship and show that charge utilization, rather than optical absorption alone, governs performance.
- Open Access
- 6 March 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (5) , 05SP18
Single-axis gold micro-electro-mechanical-systems capacitive accelerometer with circular proof-mass for suppressing warpage
This paper describes the structural stability and device characteristics of a single-axis gold proof-mass micro-electro-mechanical-systems (MEMS) capacitive accelerometer fabricated using Ti/Au multilayer metal technology. We propose a circular proof-mass structure to suppress warping deformation of the proof-mass caused by the mismatch in thermal expansion coefficients between Ti and Au. The measured warpage of the fabricated device is less than 1% related to the proof-mass radius. The MEMS capacitive accelerometer shows a valid capacitance–voltage ( C – V ) response characteristic due to warpage suppression. The experimental measurements determine its sensitivity and Brownian noise at 2.3 pF g −1 and 0.17 μ g Hz −1/2 , respectively. These values satisfy the specification for the detection of μ g -level acceleration. It is confirmed that the use of the circular proof-mass structure for the MEMS capacitive accelerometers realizes its structural stability with high sensitivity.
- 6 March 2026
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 65 (5) , 05SP18
Open AccessSingle-axis gold micro-electro-mechanical-systems capacitive accelerometer with circular proof-mass for suppressing warpage
This paper describes the structural stability and device characteristics of a single-axis gold proof-mass micro-electro-mechanical-systems (MEMS) capacitive accelerometer fabricated using Ti/Au multilayer metal technology. We propose a circular proof-mass structure to suppress warping deformation of the proof-mass caused by the mismatch in thermal expansion coefficients between Ti and Au. The measured warpage of the fabricated device is less than 1% related to the proof-mass radius. The MEMS capacitive accelerometer shows a valid capacitance–voltage ( C – V ) response characteristic due to warpage suppression. The experimental measurements determine its sensitivity and Brownian noise at 2.3 pF g −1 and 0.17 μ g Hz −1/2 , respectively. These values satisfy the specification for the detection of μ g -level acceleration. It is confirmed that the use of the circular proof-mass structure for the MEMS capacitive accelerometers realizes its structural stability with high sensitivity.
- 23 February 2026
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 9 (9) , 4302-4314
Effect of Calcination Temperature on Photocatalytic and Fenton-like Dye Degradation over Spinel CoCr 2 O 4 Nanomaterials
- 23 February 2026
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 9 (9) , 4302-4314
Effect of Calcination Temperature on Photocatalytic and Fenton-like Dye Degradation over Spinel CoCr 2 O 4 Nanomaterials
- 20 January 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (3)
Effect of Supercritical Carbon Dioxide Emulsification on Nickel Electroplating in Sulfamate Baths at Various CO₂ Volume Fractions
This study examines nickel electroplating in supercritical carbon dioxide (scCO₂)-emulsified nickel sulfamate baths, focusing on the effects of CO₂ volume fractions (10–80 vol.%) at a current density of 0.12 A/cm². The inclusion of scCO₂ significantly enhanced film quality, even at high CO₂ concentrations. However, Faradaic efficiency (FE) decreased from 95% to 75% as CO₂ volume fractions increased, attributed to intensified hydrogen evolution reactions (HER) caused by more negative deposition potentials and the insulating scCO₂ dispersed phase. Electrochemical analysis revealed pronounced potential fluctuations at higher CO₂ fractions due to intermittent electrode contact with the dispersed phase, which amplified HER and reduced the effective plating area. The conductivity of the scCO₂-emulsified bath followed the Maxwell–Garnett model, indicating isolated scCO₂ dispersed phases in a conductive medium. Despite reductions in FE and Vickers hardness (from 750 to 580 Hv), the films maintained smooth surfaces and fine grain sizes (~10 nm). These results demonstrate the potential of scCO₂ emulsification to produce high-quality nickel coatings and provide a framework for advancing electroplating in complex multiphase electrolytes.
- 20 January 2026
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 173 (3)
Effect of Supercritical Carbon Dioxide Emulsification on Nickel Electroplating in Sulfamate Baths at Various CO₂ Volume Fractions
This study examines nickel electroplating in supercritical carbon dioxide (scCO₂)-emulsified nickel sulfamate baths, focusing on the effects of CO₂ volume fractions (10–80 vol.%) at a current density of 0.12 A/cm². The inclusion of scCO₂ significantly enhanced film quality, even at high CO₂ concentrations. However, Faradaic efficiency (FE) decreased from 95% to 75% as CO₂ volume fractions increased, attributed to intensified hydrogen evolution reactions (HER) caused by more negative deposition potentials and the insulating scCO₂ dispersed phase. Electrochemical analysis revealed pronounced potential fluctuations at higher CO₂ fractions due to intermittent electrode contact with the dispersed phase, which amplified HER and reduced the effective plating area. The conductivity of the scCO₂-emulsified bath followed the Maxwell–Garnett model, indicating isolated scCO₂ dispersed phases in a conductive medium. Despite reductions in FE and Vickers hardness (from 750 to 580 Hv), the films maintained smooth surfaces and fine grain sizes (~10 nm). These results demonstrate the potential of scCO₂ emulsification to produce high-quality nickel coatings and provide a framework for advancing electroplating in complex multiphase electrolytes.
- 20 October 2025
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 8 (43) , 20952-20960
Piezoelectricity Induced by Na-Doping in NiFe 2 O 4 Nanoparticles for Piezocatalytic Dye Degradation
- 20 October 2025
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 8 (43) , 20952-20960
Piezoelectricity Induced by Na-Doping in NiFe 2 O 4 Nanoparticles for Piezocatalytic Dye Degradation
- 1 October 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (10) , 102508
Evaluation of the Annealing Induced Warpage of an Electrodeposited-Au Octagonal Proof Mass with a Ti/Au Multi-Layered Structure toward MEMS Capacitive Accelerometers
This paper reports the effects of annealing on the concave warpage deformation of an electrodeposited-Au octagonal proof mass with a Ti/Au multi-layered structure. The octagonal proof mass is fabricated by using multi-layer metal technology, which consists of the gold electrodeposition and sacrificial film formation. The annealing at and below 150 °C hardly deforms the octagonal proof mass, whereas the annealing at 200 °C induces its concave warpage deformation, and the increase in the annealing temperature causes greater deformation. On the other hand, even after the annealing at 300 °C, the warpage of the octagonal proof mass remains only 1% of the length from the center to the periphery of the octagonal proof mass. Also, the measured warpage is found to be approximately one-seventh that of the electrodeposited-Au square proof mass with the almost same size. These results reveal that the change in the proof mass structures from the square shape to the octagonal shape is significantly advantageous in suppressing its warpage deformation.
- 1 October 2025
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 172 (10) , 102508
Evaluation of the Annealing Induced Warpage of an Electrodeposited-Au Octagonal Proof Mass with a Ti/Au Multi-Layered Structure toward MEMS Capacitive Accelerometers
This paper reports the effects of annealing on the concave warpage deformation of an electrodeposited-Au octagonal proof mass with a Ti/Au multi-layered structure. The octagonal proof mass is fabricated by using multi-layer metal technology, which consists of the gold electrodeposition and sacrificial film formation. The annealing at and below 150 °C hardly deforms the octagonal proof mass, whereas the annealing at 200 °C induces its concave warpage deformation, and the increase in the annealing temperature causes greater deformation. On the other hand, even after the annealing at 300 °C, the warpage of the octagonal proof mass remains only 1% of the length from the center to the periphery of the octagonal proof mass. Also, the measured warpage is found to be approximately one-seventh that of the electrodeposited-Au square proof mass with the almost same size. These results reveal that the change in the proof mass structures from the square shape to the octagonal shape is significantly advantageous in suppressing its warpage deformation.