Mingchen Lv
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mingchen Lv has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Xuye Zhuang
School of Mechanical Engineering, Shandong University of Technology, Zibo 255049, China
3 shared publications - Jiaqi Miao
College of Mechanical Engineering, Shandong University of Technology, Zibo 255000, China
2 shared publications - Pinghua Li
College of Mechanical Engineering, Shandong University of Technology, Zibo 255000, China
2 shared publications - Qi Qiao
College of Mechanical Engineering, Shandong University of Technology, Zibo 255000, China
2 shared publications - Ruimei Liang
College of Mechanical Engineering, Shandong University of Technology, Zibo 255000, China
2 shared publications - Gaolin Li
School of Mechanical Engineering, Shandong University of Technology, Zibo, Shandong, People’s Republic of China
1 shared publication
Latest Publications
- Open Access
- 18 August 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (8) , 1049
Resonant MEMS Accelerometer with Low Cross-Axis Sensitivity—Optimized Based on BP and NSGA-II Algorithms
This article proposes a low cross-axis sensitivity resonant MEMS(Micro-Electro-Mechanical Systems) accelerometer that is optimized based on the BP and NSGA-II algorithms. When resonant accelerometers are used in seismic monitoring, automotive safety systems, and navigation applications, high immunity and low cross-axis sensitivity are required. To improve the high immunity of the accelerometer, a coupling structure is introduced. This structure effectively separates the symmetric and antisymmetric mode frequencies of the DETF resonator and prevents mode coupling. To obtain higher detection accuracy and low cross-axis sensitivity, a decoupling structure is introduced. To find the optimal dimensional parameters of the decoupled structure, the BP and NSGA-II algorithms are used to optimize the dimensional parameters of the decoupled structure. The optimized decoupled structure has an axial stiffness of 6032.21 N/m and a transverse stiffness of 6.29 N/m. The finite element analysis results show that the sensitivity of the accelerometer is 59.1 Hz/g (Y-axis) and 59 Hz/g (X-axis). Cross-axis sensitivity is 0.508% (Y-axis) and 0.339% (X-axis), which is significantly lower than most resonant accelerometers. The coupling structure and optimization method proposed in this paper provide a new solution for designing resonant accelerometers with high interference immunity and low cross-axis sensitivity.
- 18 August 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (8) , 1049
Open AccessResonant MEMS Accelerometer with Low Cross-Axis Sensitivity—Optimized Based on BP and NSGA-II Algorithms
This article proposes a low cross-axis sensitivity resonant MEMS(Micro-Electro-Mechanical Systems) accelerometer that is optimized based on the BP and NSGA-II algorithms. When resonant accelerometers are used in seismic monitoring, automotive safety systems, and navigation applications, high immunity and low cross-axis sensitivity are required. To improve the high immunity of the accelerometer, a coupling structure is introduced. This structure effectively separates the symmetric and antisymmetric mode frequencies of the DETF resonator and prevents mode coupling. To obtain higher detection accuracy and low cross-axis sensitivity, a decoupling structure is introduced. To find the optimal dimensional parameters of the decoupled structure, the BP and NSGA-II algorithms are used to optimize the dimensional parameters of the decoupled structure. The optimized decoupled structure has an axial stiffness of 6032.21 N/m and a transverse stiffness of 6.29 N/m. The finite element analysis results show that the sensitivity of the accelerometer is 59.1 Hz/g (Y-axis) and 59 Hz/g (X-axis). Cross-axis sensitivity is 0.508% (Y-axis) and 0.339% (X-axis), which is significantly lower than most resonant accelerometers. The coupling structure and optimization method proposed in this paper provide a new solution for designing resonant accelerometers with high interference immunity and low cross-axis sensitivity.
- Open Access
- 10 April 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (4) , 509
Design and Optimization of MEMS Resonant Pressure Sensors with Wide Range and High Sensitivity Based on BP and NSGA-II
With the continuous progress of aerospace, military technology, and marine development, the MEMS resonance pressure sensor puts forward the requirements of not only a wide range but also high sensitivity. However, traditional resonators are hardly compatible with both. In response, we propose a new sensor structure. By arranging the resonant beam and the sensitive diaphragm vertically in space, the new structure improves the rigidity of the diaphragm without changing the thickness of the diaphragm and achieves the purpose of increasing the range without affecting the sensitivity. To find the optimal structural parameters for the sensor sensitivity and range, and to prevent the effects of modal disturbances, we propose a multi-objective optimization design scheme based on the BP and NSGA-II algorithms. The optimization of the structure parameters not only improved the sensitivity but also increased the interference frequency to solve the issue of mode interference. The optimized structure achieves a sensitivity and range of 4.23 Hz/kPa and 1–10 MPa, respectively. Its linear influence factor is 38.07, significantly higher than that of most resonant pressure sensors. The structural and algorithmic optimizations proposed in this paper provide a new method for designing resonant pressure sensors compatible with a wide range and high sensitivity.
- 10 April 2024
- Published by MDPI AG in Micromachines
- Vol. 15 (4) , 509
Open AccessDesign and Optimization of MEMS Resonant Pressure Sensors with Wide Range and High Sensitivity Based on BP and NSGA-II
With the continuous progress of aerospace, military technology, and marine development, the MEMS resonance pressure sensor puts forward the requirements of not only a wide range but also high sensitivity. However, traditional resonators are hardly compatible with both. In response, we propose a new sensor structure. By arranging the resonant beam and the sensitive diaphragm vertically in space, the new structure improves the rigidity of the diaphragm without changing the thickness of the diaphragm and achieves the purpose of increasing the range without affecting the sensitivity. To find the optimal structural parameters for the sensor sensitivity and range, and to prevent the effects of modal disturbances, we propose a multi-objective optimization design scheme based on the BP and NSGA-II algorithms. The optimization of the structure parameters not only improved the sensitivity but also increased the interference frequency to solve the issue of mode interference. The optimized structure achieves a sensitivity and range of 4.23 Hz/kPa and 1–10 MPa, respectively. Its linear influence factor is 38.07, significantly higher than that of most resonant pressure sensors. The structural and algorithmic optimizations proposed in this paper provide a new method for designing resonant pressure sensors compatible with a wide range and high sensitivity.
- Open Access
- 16 May 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (5) , 1054
Design and Optimization of Hemispherical Resonators Based on PSO-BP and NSGA-II
Although one of the poster children of high-performance MEMS (Micro Electro Mechanical Systems) gyroscopes, the MEMS hemispherical resonator gyroscope (HRG) is faced with the barrier of technical and process limits, which makes it unable to form a resonator with the best structure. How to obtain the best resonator under specific technical and process limits is a significant topic for us. In this paper, the optimization of a MEMS polysilicon hemispherical resonator, designed by patterns based on PSO-BP and NSGA-II, was introduced. Firstly, the geometric parameters that significantly contribute to the performance of the resonator were determined via a thermoelastic model and process characteristics. Variety regulation between its performance parameters and geometric characteristics was discovered preliminarily using finite element simulation under a specified range. Then, the mapping between performance parameters and structure parameters was determined and stored in the BP neural network, which was optimized via PSO. Finally, the structure parameters in a specific numerical range corresponding to the best performance were obtained via the selection, heredity, and variation of NSGAII. Additionally, it was demonstrated using commercial finite element soft analysis that the output of the NSGAII, which corresponded to the Q factor of 42,454 and frequency difference of 8539, was a better structure for the resonator (generated by polysilicon under this process within a selected range) than the original. Instead of experimental processing, this study provides an effective and economical alternative for the design and optimization of high-performance HRGs under specific technical and process limits.
- 16 May 2023
- Published by MDPI AG in Micromachines
- Vol. 14 (5) , 1054
Open AccessDesign and Optimization of Hemispherical Resonators Based on PSO-BP and NSGA-II
Although one of the poster children of high-performance MEMS (Micro Electro Mechanical Systems) gyroscopes, the MEMS hemispherical resonator gyroscope (HRG) is faced with the barrier of technical and process limits, which makes it unable to form a resonator with the best structure. How to obtain the best resonator under specific technical and process limits is a significant topic for us. In this paper, the optimization of a MEMS polysilicon hemispherical resonator, designed by patterns based on PSO-BP and NSGA-II, was introduced. Firstly, the geometric parameters that significantly contribute to the performance of the resonator were determined via a thermoelastic model and process characteristics. Variety regulation between its performance parameters and geometric characteristics was discovered preliminarily using finite element simulation under a specified range. Then, the mapping between performance parameters and structure parameters was determined and stored in the BP neural network, which was optimized via PSO. Finally, the structure parameters in a specific numerical range corresponding to the best performance were obtained via the selection, heredity, and variation of NSGAII. Additionally, it was demonstrated using commercial finite element soft analysis that the output of the NSGAII, which corresponded to the Q factor of 42,454 and frequency difference of 8539, was a better structure for the resonator (generated by polysilicon under this process within a selected range) than the original. Instead of experimental processing, this study provides an effective and economical alternative for the design and optimization of high-performance HRGs under specific technical and process limits.